Dominant Effect of Support Wettability on the Reaction Pathway for Catalytic Wet Air Oxidation over Pt and Ru Nanoparticle Catalysts

Catalytic wet air oxidation of toxic containments over highly dispersed Cu(II)/Cu(I)-N species in the framework of g-C3N4

Catalytic wet air oxidation (CWAO) is a harmless, cheap and effective technology for the degradation of toxic containments directly to CO₂ and H₂O. In this work, highly dispersed Cu(II)/Cu(I)-N that embedded in the framework of g-C₃N₄ (Cu_x-g-C₃N₄) were synthesized in a facile thermal polymerization method and used in the CWAO of phenols, antibiotics and vitamins. Characterization results confirmed that g-C₃N₄ formed in the prepared catalyst and copper was chemically coordinated with N in g-C₃N₄, which inhibited the aggregation of copper. Meanwhile, Cu(II) or Cu(I) in the framework of g-C₃N₄ was more effective for the degradation of phenol than Cu(0) and CuO, and more than 23 toxic containments could be degraded under mild conditions. The prominent performance of Cu_0.1-g-C₃N₄ for CWAO reaction was discussed on the base of these experiments and it was disclosed that in-situ formed H₂O₂ might be contributed to the highly activity.

Monodisperse thiourea functionalized graphene oxide-based PtRu nanocatalysts for alcohol oxidation

Addressed herein, thiourea functionalized graphene oxide-based PtRu nanocatalysts (PtRu@T/GO) has been synthesized and characterized by several techniques and performed for methanol oxidation reactions as novel catalysts. In this study, graphene oxide (GO) was functionalized with thiourea (T/GO) in order to obtain monothiol functionalized graphene and increase the stability and activity of the nanocatalysts. Raman spectroscopy, X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), TEM (transmission electron microscopy) and high-resolution transmission electron microscopy (HR-TEM) were used for characterization of the prepared nanocatalysts. The results obtained from these techniques showed that the prepared nanocatalysts were in a highly crystalline form, well dispersed on T/GO, very small in size and colloidally stable. The average size of the synthesized nanocatalysts determined by TEM analysis was found to be 3.86 ± 0.59 nm. With HR-TEM analysis, the atomic lattice fringes of the nanocatalysts were calculated to be 0.23 nm. After the full characterization of the prepared nanocatalysts, they were tried for the methanol oxidation reaction (MOR) and it was observed that 97.3% of the initial performance was maintained even after 1000 cycles while exhibiting great catalytic activity and stability with the help of T/GO. Thus, the arranged nanocatalysts displayed great heterogeneous catalyst characteristics for the methanol oxidation response.

Room-temperature air oxidation of organic pollutants via electrocatalysis by nanoscaled Co-CoO on graphite felt anode

Oxygen (O₂) in air is an eco-friendly and economical oxidant. However, its activation is an energy-intensive process requiring high operation temperature. Herein, we report the synthesis of nanoscaled Co-CoO on a graphite felt (GF) as an anode material for electrocatalytic wet air oxidation (ECWAO) of water contaminants at room temperature. Such an ECWAO process shows extensive effectiveness in mineralizing a variety of biorefractory organic pollutants. A probe pollutant, bisphenol A (BPA), is rapidly degraded in 180 min with mineralization efficiencies higher than 85% over a wide pH range from 3.0 to 11.0. The Co-CoO/GF electrode exhibits excellent stability in the ECWAO process, without loss of activity and leaching of metal. The ECWAO process is confirmed to be initiated by the electrochemical activation of O₂ through a non-radical pathway. The CoO on the surface of Co nanoparticle is identified as the catalytically active site, at which O₂ molecules are first converted to chemisorbed oxygen species and then electrochemically oxidized to their activated states. The ECWAO process with the Co-CoO/GF electrode presents the merits of high efficiency, low energy input and environmental friendliness, and has a great potential for practical wastewater treatment.

Ternary semiconductor metal oxide blends grafted Ag@AgCl hybrid as dimensionally stable anode active layer for photoelectrochemical oxidation of organic compounds: Design strategies and photoelectric synergistic mechanism

The development of ultra-efficient, sustainable, and easily accessible anode with relative non-precious semiconducting metal oxides is highly significant for application in the practical treatment of organically polluted water. Herein, we report SnO₂, TiO₂, and Ag₂O ternary semiconductor metal oxide blend grafted Ag@AgCl hybrids, prepared with the one-step sol-gel method and applied as a dimensionally stable anode (DSA)-active layer on a SnO₂-Sb/Ti electrode. Factors affecting crystal formation, including the presence or absence of O₂ during calcination, the calcination temperature, and Ag@AgCl additive dosage were discussed. The micromorphology, phase composition, and photoelectrochemical activity of the newly designed anode were comprehensively characterized. The optimized preparation, which yielded a solid-solution structure with flat and smooth surface and well-crystallized lattice configuration, occurred in the absence of O₂ during calcination at 550 ℃ with an Ag@AgCl additive dosage of 0.2 g in the sol-gel precursor. The newly designed DSA displayed improved electrocatalysis (EC) and photoelectrical catalysis (PEC) capacity. The phenol and its TOC removal efficiency reached 90.65% and 58.17% for 10 mA/cm² current density with a metal halide lamp in 3 h. The lifespan was four times that of SnO₂-Sb/Ti electrode. This proposed DSA construction strategy may support improved EC and PEC reactivities toward the decomposition of organic pollutants.