Interfacial Liquid Water on Graphite, Graphene, and 2D Materials

Two-dimensional ice-like water adlayers on a mica surface with and without a graphene coating under ambient conditions

Water tends to wet all hydrophilic surfaces under ambient conditions, and the first water adlayers on solids are important for a broad range of physicochemical phenomena and technological processes, including corrosion, wetting, lubrication, anti-icing, catalysis, and electrochemistry. Unfortunately, challenges in characterizing the first water adlayer in the laboratory have hampered molecular-level understanding of the contact water structure. Herein, we present the first ab initio molecular dynamics simulation evidence of a previously unreported ice-like adlayer structure (named as Ice-AL-II) on a prototype mica surface under ambient conditions. Calculation showed that the newly identified Ice-AL-II structure is more stable than the widely recognized ice-adlayer structure on mica surfaces (named as Ice-AL-I). Ice-AL-II exhibited a face-centered corner-cut tetragon (or a face-centered irregular pentagon) pattern of a hydrogen-bonded network. The center of the corner-cut tetragon was occupied by either a K+ cation or a water molecule with two H atoms pinned by the mica (100) via double hydrogen bonds. Our simulation also suggested that bilayer Ice-AL-II favors AA stacking rather than AB stacking. Interestingly, when a graphene sheet was coated on top of the ice-like adlayer, the stability of Ice-AL-II was further enhanced. In contrast, due to its strongly puckered structure, the Ice-AL-I structure could be crushed into a near-Ice-AL-II structure by the graphene coating. Ice-AL-II is thus proposed as a promising candidate for the ice-like structure on a mica surface detected by scanning polarization force microscopy and by atomic force microscopy between a graphene coating and a mica surface.

Interfacial water on collagen nanoribbons by 3D AFM

Collagen is the most abundant structural protein in mammals. Type I collagen in its fibril form has a characteristic pattern structure that alternates two regions called gap and overlap. The structure and properties of collagens are highly dependent on the water and mineral content of the environment. Here, we apply 3D AFM to characterize at angstrom-scale resolution the interfacial water structure of collagen nanoribbons. For a neutral tip, the interfacial water structure is characterized by the oscillation of the water particle density distribution with a value of 0.3 nm (hydration layers). The interfacial structure does not depend on the collagen region. For a negatively charged tip, the interfacial structure might depend on the collagen region. Hydration layers are observed in overlap regions, while in gap regions, the interfacial solvent structure is dominated by electrostatic interactions. These interactions generate interlayer distances of 0.2 nm.

Open-[60]fullerenols with water adsorbed both inside and outside

The water affinity on [60]fullerenols was found to be governed by surface electrostatic potential while water aggregation is initiated by the hydroxy groups attached on the carbon surface. The molecular water adsorption at the internal sphere caused a significnat inhibition of water adsorption at the external carbon surface.

Exploring the Surface Oxidation and Environmental Instability of 2H-/1T'-MoTe2 Using Field Emission-Based Scanning Probe Lithography

An unconventional approach for the resistless nanopatterning 2H- and 1T'-MoTe2 by means of scanning probe lithography is presented. A Fowler-Nordheim tunneling current of low energetic electrons (E = 30-60 eV) emitted from the tip of an atomic force microscopy (AFM) cantilever is utilized to induce a nanoscale oxidation on a MoTe2 nanosheet surface under ambient conditions. Due to the water solubility of the generated oxide, a direct pattern transfer into the MoTe2 surface can be achieved by a simple immersion of the sample in deionized water. The tip-grown oxide is characterized using Auger electron and Raman spectroscopy, revealing it consists of amorphous MoO3 /MoOx as well as TeO2 /TeOx . With the presented technology in combination with subsequent AFM imaging it is possible to demonstrate a strong anisotropic sensitivity of 1T'-/(Td )-MoTe2 to aqueous environments. Finally the discussed approach is used to structure a nanoribbon field effect transistor out of a few-layer 2H-MoTe2 nanosheet.

Effect of terahertz electromagnetic field on single-file water transport through a carbon nanotube

With the advancement in terahertz technology, the terahertz electromagnetic field has been proven to be an effective strategy to tune the nanofluidic transport. In this study, we utilize molecular dynamics simulations to systematically analyze the transport of single-file water through a carbon nanotube (CNT) under terahertz electromagnetic fields, focusing on the CNT length, field strength, polarization direction and frequency. Strikingly, with the increase in field strength, the water flow exhibits a transition from normal to super permeation states because of the resonance effect, and the threshold field shifts to low values for long CNTs. The field component parallel to the CNT axis contributes to the resonance effect and increasing water flow, but the vertical component maintains the structure of the single-file water chain and even impedes the water flow. As a result, for a continuous change of field direction, the water flow changes from super permeation to normal states. With the increase in field frequency, the water flow also changes from super permeation to normal or even frozen states, where a higher frequency is required to trigger the super permeation states for lower field strength. Our results provide a comprehensive insight into the effect of terahertz electromagnetic field on the transport of single-file water chains and should have great implications for designing novel nanofluidic devices.

Ion and water adsorption to graphene and graphene oxide surfaces

Graphene and graphene oxide (GO) are two particularly promising nanomaterials for a range of applications including energy storage, catalysis, and separations. Understanding the nanoscale interactions between ions and water near graphene and GO surfaces is critical for advancing our fundamental knowledge of these systems and downstream application success. This minireview highlights the necessity of using surface-specific experimental probes and computational techniques to fully characterize these interfaces, including the nanomaterial, surrounding water, and any adsorbed ions, if present. Key experimental and simulation studies considering water and ion structures near both graphene and GO are discussed. The major findings are: water forms 1-3 hydration layers near graphene; ions adsorb electrostatically to graphene under an applied potential; the chemical and physical properties of GO vary considerably depending on the synthesis route; and these variations influence water and ion adsorption to GO. Lastly, we offer outlooks and perspectives for these research areas.