Revealing the Effects of Microarc Oxidation on the Mechanical and Degradation Properties of Mg-Based Biodegradable Composites

Tribological properties of MAO ceramic coatings with annulus array texture on disposable surgical gloves

Introduction: In recent research, the expansion in the use of Mg alloys for biomedical applications has been approached by modifying their surfaces in conjunction with micro-arc oxidation (MAO) techniques which enhance their abrasion and corrosion resistance. Methods: In this study, combining laser texturing and MAO techniques to produce the dense ceramic coatings with microstructures. On the surface of the AZ31 Mg alloy, a micro-raised annulus array texture has been designed in order to increase the surface friction under liquid lubrication and to improve the operator's grip when holding the tool. For this work, the micro-morphology of the coatings was characterised, and the friction properties of the commonly used scalpel shank material 316 L, the untextured surface and the textured surface were comparatively analysed against disposable surgical gloves. Results and discussion: The results show that the Laser-MAO ceramic coating grows homogenous, the porosity decreases from 14.3% to 7.8%, and the morphology after friction indicates that the coating has good wear resistance. More specifically, the average coefficient of friction (COF) of the three types of gloves coated with Laser-MAO ceramic was higher than that of the 316 L and MAO ceramic coatings under the action of the annulus-integrated texture under the lubrication conditions of physiological saline and defatted sheep blood, which achieved the goal of increasing friction for the purpose of helping to prevent the problem of tool slippage from the hand.

Bioabsorbable WE43 Mg alloy wires modified by continuous plasma-electrolytic oxidation for implant applications. Part I: Processing, microstructure and mechanical properties

In our work, a novel processing strategy for the continuous fabrication and surface modification of wires from Magnesium alloy WE43 by means of plasma-electrolytic oxidation (PEO) is presented. In the first step, wires with a strong basal texture and small grain size (≈ 1 μm) were manufactured by combined cold drawing and in-line stress-relief heat treatment steps that optimized the mechanical properties (in terms of strength and ductility) by means of annealing. In a second step, and to the best of our knowledge for the first time ever, the wires were continuously surface-modified with a novel plasma electrolytic oxidation process, which was able to create a homogeneous porous oxide layer made of MgO and Mg₃(PO₄)₂ on the wire surface. While the oxide layer slightly diminished the tensile properties, the strength of the surface-modified wires could be maintained close to 300 MPa with a strain-to-failure ≈ 8 %. Furthermore, the thickness of the oxide layer could be controlled by immersion time within the electrolytic bath and was adjusted to realize a thicknesses of ≈ 8 μm, which could be obtained in <20 s. Our experiments showed that the chemical composition, morphology and porosity of the oxide layer could be tailored by changing electrical parameters. The combined cold drawing and heat treatment process with additional continuous plasma electrolytic oxidation processing can be upscaled to produce a novel generation of bioabsorbable Mg wires with optimized mechanical, degradation and biological performance for use in biomedical applications.

Progress in bioactive surface coatings on biodegradable Mg alloys: A critical review towards clinical translation

Mg and its alloys evince strong candidature for biodegradable bone implants, cardiovascular stents, and wound closing devices. However, their rapid degradation rate causes premature implant failure, constraining clinical applications. Bio-functional surface coatings have emerged as the most competent strategy to fulfill the diverse clinical requirements, besides yielding effective corrosion resistance. This article reviews the progress of biodegradable and advanced surface coatings on Mg alloys investigated in recent years, aiming to build up a comprehensive knowledge framework of coating techniques, processing parameters, performance measures in terms of corrosion resistance, adhesion strength, and biocompatibility. Recently developed conversion and deposition type surface coatings are thoroughly discussed by reporting their essential therapeutic responses like osteogenesis, angiogenesis, cytocompatibility, hemocompatibility, anti-bacterial, and controlled drug release towards in-vitro and in-vivo study models. The challenges associated with metallic, ceramic and polymeric coatings along with merits and demerits of various coatings have been illustrated. The use of multilayered hybrid coating comprising a unique combination of organic and inorganic components has been emphasized with future perspectives to obtain diverse bio-functionalities in a facile single coating system for orthopedic implant applications.

•

The challenges and current status of coatings are reviewed in light of clinical requirements.

•

Multilayered hybrid coatings have been emphasized to obtain diverse bio-functionalities.

•

The future developments and research directions on coatings for biodegradable implants are highlighted.