Solventless Preparation of Thoria and Its Inclusion into SiO2 and TiO2: A Luminescence and Photocatalysis Study

Color tunable luminescence in ThO2:Er3+,Yb3+ nanocrystals: a promising new platform for upconversion

Lanthanide-doped luminescent nanoparticles are an appealing system for many applications in the area of biomedical, solar cell, thermometry, anti-counterfeiting, etc. due to their sensitivity, reliability, high photochemical stability, and high optical transparency in the visible-NIR range. A color-tunable upconversion-luminescence (UCL) in a new low phonon energy ThO2 host based on modulating sensitizer concentration has been realized in this work and it may work as a potential candidate to replace corrosive and toxic fluoride based hosts in the future. Er3+-Yb3+ co-doped thoria nanoparticles were prepared using a gel combustion route and their structural and luminescence properties were determined as a function of the Yb3+ concentration. Phonon dispersion measurements have established the dynamic structural stability of the thoria nanoparticles. Density functional theory (DFT) was used to calculate the defect formation energy, highlighting the feasibility of dual ion (Er3+ and Yb3+) doping in thoria. The morphology and average size of the doped thoria was studied using high resolution transmission electron microscopy (HRTEM), and any defects evolving as a result of aliovalent doping were probed using positron annihilation lifetime spectroscopy (PALS). With 980 nm laser excitation, the nanothoria emits green and near-red light. A significant enhancement of the red-to-green intensity ratio of Er3+ ions in nanothoria was observed with an increase in Yb3+ concentration which resulted in beautiful color tunability from green to yellow light in going from lower (up to ∼5 mol%) to higher (10 and 15 mol%) Yb3+ concentration. The power dependence and the dynamics of the upconverted emission confirm the existence of two-photon upconversion processes for the green and red emissions.

Solid-State Preparation of Metal and Metal Oxides Nanostructures and Their Application in Environmental Remediation

Nanomaterials have attracted much attention over the last decades due to their very different properties compared to those of bulk equivalents, such as a large surface-to-volume ratio, the size-dependent optical, physical, and magnetic properties. A number of solution fabrication methods have been developed for the synthesis of metal and metal oxides nanoparticles, but few solid-state methods have been reported. The application of nanostructured materials to electronic solid-state devices or to high-temperature technology requires, however, adequate solid-state methods for obtaining nanostructured materials. In this review, we discuss some of the main current methods of obtaining nanomaterials in solid state, and also we summarize the obtaining of nanomaterials using a new general method in solid state. This new solid-state method to prepare metals and metallic oxides nanostructures start with the preparation of the macromolecular complexes chitosan·Xn and PS-co-4-PVP·MXn as precursors (X = anion accompanying the cationic metal, n = is the subscript, which indicates the number of anions in the formula of the metal salt and PS-co-4-PVP = poly(styrene-co-4-vinylpyridine)). Then, the solid-state pyrolysis under air and at 800 °C affords nanoparticles of M°, M_xO_y depending on the nature of the metal. Metallic nanoparticles are obtained for noble metals such as Au, while the respective metal oxide is obtained for transition, representative, and lanthanide metals. Size and morphology depend on the nature of the polymer as well as on the spacing of the metals within the polymeric chain. Noticeably in the case of TiO₂, anatase or rutile phases can be tuned by the nature of the Ti salts coordinated in the macromolecular polymer. A mechanism for the formation of nanoparticles is outlined on the basis of TG/DSC data. Some applications such as photocatalytic degradation of methylene by different metal oxides obtained by the presented solid-state method are also described. A brief review of the main solid-state methods to prepare nanoparticles is also outlined in the introduction. Some challenges to further development of these materials and methods are finally discussed.