Enhanced Visible-Light Absorption of Fe2O3 Covered by Activated Carbon for Multifunctional Purposes: Tuning the Structural, Electronic, Optical, and Magnetic Properties

From colors to currents: a hybrid electrochemical and colorimetric sensor for real-time detection of emerging pollutants and pH monitoring

The development of new tools for detecting and monitoring emerging pollutants is highly desired in the environmental field. Here, we report a hybrid multiplexed sensor for colorimetric detection of nitrite (NO2-) and pH, along with simultaneous electrochemical detection of methylparaben (MP) and bisphenol A (BPA) in tap, lake and natural water. Through a portable potentiostat and a smartphone, our device provides relevant environmental parameters within two minutes. The colorimetric sensors were fabricated through spot tests, detecting NO2- at a concentration ranging from 1 to 200 μmol L-1, with a limit of detection (LOD) of 3.0 μmol L-1. The electrochemical sensors for MP and BPA were fabricated using the laser-scribed graphene (LSG) technique on a polyamide (PI) substrate. We achieved LODs of 0.22 μmol L-1 (MP) and 0.057 μmol L-1 (BPA), ranging from 1 to 100 μmol L-1 for both, and reproducibility with relative standard deviations (RSDs) of 2.5% (MP) and 4.8% (BPA). As a proof-of-concept, our device was tested using real samples of lake, tap and natural water, achieving recoveries from 93% to 120%, demonstrating its suitability for in-field applications for environmental analyses.

Adsorption and photocatalytic degradation of 2,4-dicholrophenol using surgical mask derived SMAC-Fe2O3 composite; adsorption isotherms, kinetics, thermodynamics

Hybrid material of surgical mask activated carbon (SMAC) and Fe2O3 (SMAC-Fe2O3) composite was prepared by simple co-precipitation method and used as potential material for the remediation of 2,4-dicholrophenol (2,4-DCP). The XRD patterns exhibited the presence of SMAC and Fe2O3, FTIR spectrum showed the FeO-carbon stretching at the wavenumber from 400 to 550 cm-1. UV-Vis DRS results showed the band gap was 1.97 eV and 2.05 eV for SMAC-Fe2O3 and Fe2O3, respectively. The SEM images revealed that the Fe2O3 doped onto the fiber morphology of SMAC. The outcomes of the BET examination exhibited a surface area of 195 m2/g and a pore volume of 0.2062 cm3/g for the SMAC/Fe2O3 composite. The batch mode study shows the maximum adsorption and photocatalytic degradation efficacies which were 97% and 78%, respectively. The experimental data was studied with both linear and nonlinear adsorption isotherm and kinetics models. The nonlinear Langmuir isotherm and pseudo-second-order kinetics (PSOK) models have well fit compared with other models. The Langmuir maximum adsorption capacity (qmax) was found 161.60 mg/g. Thermodynamic analysis shows that the 2,4-DCP adsorption onto SMAC-Fe2O3 was a spontaneous and exothermic process. The PSOK assumes that the adsorption process was chemisorption. The photocatalytic degradation rate constant of 2,4-DCP was calculated using pseudo-first-order kinetics (PFOK) and the rate constant for SMAC-Fe2O3 and Fe2O3 were 0.859 × 10-2 min-1 and 0.616 × 10-2 min-1, correspondingly. In addition, the obtained composite exhibited good reusability after a few cycles. These results confirmed that SMAC-Fe2O3 composite is an effective adsorbent and photocatalyst for removing 2,4-DCP pollutants.

Lightweight ZnO/Carbonated Cotton Fiber Nanocomposites for Electromagnetic Interference Applications: Preparation and Properties

Electromagnetic wave pollution has become a significant harm posed to human health and precision instruments. To shelter such instruments from electromagnetic radiation, high-frequency electromagnetic interference (EMI) shielding materials are extremely desirable. The focus of this research is lightweight, high-absorption EMI shielding composites. Simple aqueous dispersion and drying procedures were used to prepare cotton fiber (CF)-based sheets combined with various zinc oxide (ZnO) contents. These composites were carbonated in a high-temperature furnace at 800 °C for two hours. The obtained CF/ZnO samples have densities of 1.02-1.08 g/cm3. The EMI shielding effectiveness of CF-30% ZnO, CF-50% ZnO, and CF-70% ZnO reached 32.06, 38.08, and 34.69 dB, respectively, to which more than 80% of absorption is attributed. The synergetic effects of carbon networks and surface structures are responsible for the high EMI shielding performance; various reflections inside the interconnected networks may also help in improving their EMI shielding performance.

Nickel Slag/Laterite Soil and Nickel Slag/Iron Sand Nanocomposites: Structural, Optical, and Electromagnetic Absorption Properties

Efforts to produce microwave absorber materials that are inexpensive and environmentally friendly have become a means of greening the environment. The breakthrough can be focused on industrial waste and natural materials for functional purposes and how to enhance their performance. We successfully synthesized nickel slag/laterite soil (NS/LS) and nickel slag/iron sand (NS/IS) nanocomposites using a simple mechanical alloying technique, and the electromagnetic (EM) wave absorption capacities of the nanocomposites were measured using a vector network analyzer. The structural properties of the nanocomposites were analyzed by X-ray diffraction spectroscopy, where the results of the analysis showed that NS/IS has the largest crystallite size (15.69 nm) and the highest EM wave absorption performance. The optical properties of the nanocomposites were determined from their Fourier transform infrared spectra using the Kramers-Kronig relation. As determined through a quantitative analysis of the optical properties, the distance between the longitudinal and transversal optical phonon wavenumber positions (Δ(LO - TO) = 65 cm^-1) is inversely proportional to the reflection loss. The surface morphologies of the nanocomposites were analyzed by scanning electron microscopy, and the particle diameters were observed by binary image and Gaussian distribution analyses. The nanocomposite surface exhibits a graded-like morphology, which indicates multiple reflections of the EM radiation, consequently reducing the EM interference. The best nanocomposite for an attenuated EM wave achieved a reflection loss of -39.14 dB at 5-8 GHz. A low penetration depth has implications for the electrical charge tuning of the storage and composite magnets. Finally, the EM absorption properties of NS/IS and NS/LS indicate a 2-mm-thick environmentally friendly nanocomposite for EM absorption.

Magnetic activated carbon synthesized using rubber fig tree leaves for adsorptive removal of tetracycline from aqueous solutions

The current study emphasizes the activated carbon fabrication from rubber fig leaves, the establishment of its composite with iron oxide nanoparticles (RFAC@Fe₂O₃), and its relevance in the adsorptive elimination of tetracycline. The physical and functional properties of RFAC@Fe₂O₃ nanocomposite were uncovered by multiple approaches. Elemental analysis portrayed the existence of carbon, oxygen, and iron, while FESEM analysis revealed that Fe₂O₃ nanoparticle agglomerates were entrenched in the activated carbon matrix rendering it a rough abrasive texture. FT-IR analysis reported the presence of functional groups attributing to CC, -OH, crystalline iron oxide, and Fe-O stretching vibrations, and XRD corroborated graphitic crystalline structure, oxygenated functional groups attached to carbon accompanied by crystalline plane corresponding to Fe₂O₃ nanoparticles. XPS spectra depicted signature peaks for C, O, and Fe, while VSM studies designated its superparamagnetic nature. The high surface area (662.73 m²/g), pore size (3.12 nm), and mesoporous nature of RFAC@Fe₂O₃ make it apt for the adsorption of pollutants from contaminated samples. The adsorption of tetracycline (50 ppm) by RFAC@Fe₂O₃ was maximum at pH 4.0. As the nanocomposite dosage and stirring speed increased to 2.0 g/L and 150 rpm, maximum adsorption was observed due to more active binding sites and improved mixing. Freundlich isotherm along with pseudo-second-order model well described adsorption process divulging that tetracycline was adsorbed onto RFAC@Fe₂O₃ composite in multi-layers by chemisorption. Thermodynamic analysis signified negative values for ΔG°, while positive values for ΔH° and ΔS were obtained, indicating spontaneous feasible endothermic adsorption.

Adsorptive removal of tetracycline from aqueous solutions using magnetic Fe2O3 / activated carbon prepared from Cynometra ramiflora fruit waste

Herein, the sustainable fabrication of magnetic iron oxide nanoadsorbent prepared with activated carbon of inedible Cynometra ramiflora fruit has been investigated. Activated carbon was obtained from phosphoric acid-treated C. ramiflora fruit, which was then utilized for the synthesis of magnetic nanocomposite (CRAC@Fe₂O₃). The formed nanocomposite was a porous irregular dense matrix of amorphous evenly sized spherical nanoparticles, as visualized by FESEM, and also contained carbon, oxygen, iron, and phosphorous in its elemental composition. FT-IR spectrum depicted characteristic bands attributing to Fe-O, C-OH, C-N, CC, and -OH bonds. VSM and XRD results proved that CRAC@Fe₂O₃ was superparamagnetic with a moderate degree of crystallinity and high saturation magnetization value (1.66 emu/g). Superior surface area, pore size, and pore volume of 766.75 m²/g, 2.11 nm, and 0.4050 cm³/g respectively were measured on BET analysis of CRAC@Fe₂O₃ nanocomposite, indicating their suitability for use as an adsorbent. On application of this nanocomposite for adsorption of tetracycline, maximum removal of 95.78% of 50 ppm TC at pH 4, CRAC@Fe₂O₃ 0.4 g/L in 240 min. The adsorption of TC by CRAC@Fe₂O₃ was confirmed as monolayer sorption by ionic interaction (R² = 0.9999) as it followed pseudo-second-order kinetics and Langmuir isotherm (R² = 0.9801). CRAC@Fe₂O₃ showed a maximum adsorption capacity of 312.5 mg/g towards TC antibiotics indicating its potential for the treatment of antibiotic-contaminated samples. Since negative ΔG^o and positive ΔH^o and ΔS^o values were obtained at all tested temperatures during the thermodynamic studies, the adsorption was confirmed to be endothermic, spontaneous, and feasible with an enhanced degree of randomness.