Self-Powered Potentiometric Sensor Transduction to a Capacitive Electronic Component for Later Readout

Self-Powered Potentiometric Sensor with Relational Operation Function to Capture Concentration Excursions

Self-powered potentiometric sensors spontaneously respond to activity changes of target species without the need for an external power source. Here, a self-powered potentiometric sensing approach is described that may store concentration perturbations that occur before the sensor readout through a combination of capacitors and diodes. Two channels, termed "more than" and "less than" operators, are utilized as memory modules in the sensor circuit to record positive and negative concentration excursions, respectively. Each channel is constructed with a capacitor-diode pair in which each diode is connected to a capacitor in the opposite direction to prevent unwanted capacitor discharge. With this design, only potential variations that agree with the polarity of the diode may pass and be stored in the capacitor. A limitation of the principle is that the conductivity of the diode is very small if the voltage across it diminishes over time as it approaches the equilibrium value. To address this, the forward voltage is increased by about 1 V by switching from an initial Ag/AgCl reference electrode (RE) to a Zn/Zn2+ element. The device may be used to monitor whether a concentration excursion has occurred in the time leading up to the signal readout in a semiquantitative manner. The approach also differentiates pH excursions of different durations (20, 40, 60 min). As an example, four different pH excursions of 20 min duration were successfully distinguished in river water samples with amplitudes of 1 to 4 pH units relative to the case without pH perturbation.

Towards a REASSURED reality: A less-is-more electronic design strategy for self-powered glucose test

Sensing strategies adopting minimal electronic systems help in realizing REASSURED diagnostic tests. However, the challenge in developing such strategies escalates with demand in power and electronics during pursuit of reliable and accurate sensing. Herein, we present an electronic design strategy using a smart strip, operating with power generated from 3.5 μL of serum sample, to reveal glucose concentration through a response preserved in a capacitor. Further, by integrating an NFC tag alongside the strip, we devised a self-powered glucose measuring card, mobile-glucocard (or mGlucocard) for retrieving this stored digital response using smartphone, enabling 'connected mobile-health diagnostics'. The response from our device relates linearly to glucose concentration offering a sensitivity of 11.3 mV/mM and good correlation (R = 0.974) with colorimetric reference method. Interestingly, the design strategy uses only four components - two resistors, diode, and capacitor - of simple architecture likely transferable to printed technologies to deliver advanced self-powered sustainable devices.

Self-Powered Potentiometric Sensor Based on a Passive Signal Amplifier with Electronic Paper Display

Self-powered potentiometric sensors are attractive because of their simple operation, low cost, fast response, and ability to be integrated with electronic components. Self-powered potentiometric sensors that give a direct colorimetric output are especially interesting, because no power supply is needed, which dramatically reduces waste. Recently reported work from our group using an electronic paper display, however, exhibits limitations, because the visualization of small pH changes is difficult. A self-powered ion-selective potentiometric sensor is introduced here that may amplify the e-paper pixel sensitivity by improving the self-powered circuit. The voltage is amplified by changing the circuit from incorporating parallel to incorporating serial capacitors. With three such capacitors, a greatly improved sensitivity is observed, amplifying the absorbance 3-fold. A portable device is realized that changes the position of the capacitors from parallel to serial through a simple mechanical sliding action. As a result, the pH information on the sample is more easily visualized with a pH uncertainty of about 0.1 when comparing the e-paper output to a color card.

Novel Approaches to Enzyme-Based Electrochemical Nanobiosensors

Electrochemistry is a genuinely interdisciplinary science that may be used in various physical, chemical, and biological domains. Moreover, using biosensors to quantify biological or biochemical processes is critical in medical, biological, and biotechnological applications. Nowadays, there are several electrochemical biosensors for various healthcare applications, such as for the determination of glucose, lactate, catecholamines, nucleic acid, uric acid, and so on. Enzyme-based analytical techniques rely on detecting the co-substrate or, more precisely, the products of a catalyzed reaction. The glucose oxidase enzyme is generally used in enzyme-based biosensors to measure glucose in tears, blood, etc. Moreover, among all nanomaterials, carbon-based nanomaterials have generally been utilized thanks to the unique properties of carbon. The sensitivity can be up to pM levels using enzyme-based nanobiosensor, and these sensors are very selective, as all enzymes are specific for their substrates. Furthermore, enzyme-based biosensors frequently have fast reaction times, allowing for real-time monitoring and analyses. These biosensors, however, have several drawbacks. Changes in temperature, pH, and other environmental factors can influence the stability and activity of the enzymes, affecting the reliability and repeatability of the readings. Additionally, the cost of the enzymes and their immobilization onto appropriate transducer surfaces might be prohibitively expensive, impeding the large-scale commercialization and widespread use of biosensors. This review discusses the design, detection, and immobilization techniques for enzyme-based electrochemical nanobiosensors, and recent applications in enzyme-based electrochemical studies are evaluated and tabulated.

Capacitance-Based Biosensor for the Measurement of Total Loss of L-Amino Acids in Human Serum during Hemodialysis

In this paper, we present a biosensor based on a gold nanoparticle (AuNP)-modified Pt electrode with an adjusted membrane containing cross-linked L-amino acid oxidase for the detection and quantification of total L-amino acids. The designed biosensor was tested and characterized using the capacitance-based principle, capacitance measurements after electrode polarization, disconnection from the circuit, and addition of the respective amount of the analyte. The method was implemented using the capacitive and catalytic properties of the Pt/AuNP electrode; nanostructures were able to store electric charge while at the same time catalyzing the oxidation of the redox reaction intermediate H₂O₂. In this way, the Pt/AuNP layer was charged after the addition of analytes, allowing for much more accurate measurements for samples with low amino acid concentrations. The combined biosensor electrode with the capacitance-based measurement method resulted in high sensitivity and a low limit of detection (LOD) for hydrogen peroxide (4.15 μC/μM and 0.86 μM, respectively) and high sensitivity, a low LOD, and a wide linear range for L-amino acids (0.73 μC/μM, 5.5 μM and 25-1500 μM, respectively). The designed biosensor was applied to measure the relative loss of amino acids in patients undergoing renal replacement therapy by analyzing amino acid levels in diluted serum samples before and after entering/leaving the hemodialysis apparatus. In general, the designed biosensor in conjunction with the proposed capacitance-based method was clinically tested and could also be applied for the detection of other analytes using analyte-specific oxidases.

Self-Powered Signal Transduction of Ion-Selective Electrodes to an Electronic Paper Display

Mobile integrated electrochemical sensors normally require a power supply for operation. Unfortunately, the practice of discarding batteries associated with these devices runs counter to our desire for a sustainable world. Self-powered sensing concepts that draw the energy directly from the measurement itself would overcome this limitation. Potentiometric sensors for the measurement of pH, many electrolytes, and gases are ubiquitous in analytical practice. However, in potentiometry, the voltage is acquired in the absence of current flow, making it seemingly impossible to draw power. Fortunately, it has been recently established that transient currents may be tolerated across potentiometric measurement cells to charge a capacitive or electrochromic element such as Prussian blue integrated in the measurement cell and whose absorbance then directly follows the potential changes in a reversible manner. We have shown here that commercial electronic paper (e-paper), widely used to make electronic ink and ebook readers, can directly be driven by a potentiometric measurement cell in a reversible manner at mild potentials of >100 mV typical for such sensors. The capacitance of the e-paper pixel studied here was found to be 0.53 μF mm^-2, 30 times smaller than that of Prussian blue films. The colorimetric absorbance of the e-paper was also more stable (observed drift over 2 h corresponding to 0.76 mV h^-1) and reproducible (corresponding to 1 mV standard deviation). The e-paper pixel was directly driven by a polymeric pH electrode as a model system. Choosing a basic inner solution (pH 12.9) behind the membrane gave sufficiently positive cell potentials for driving visible absorbance change in a sample pH range of 4-10, while a more acidic pH of 3.4 and alternating the connections to the e-paper were more suited for more basic samples of pH > 10. This convenient and cost-effective approach makes it possible to directly drive an optical display from the potentiometric measurement itself and should be suitable for moderate sensing membrane resistances of less than about 100 kΩ, depending on the area of the chosen pixel.

Engineering Self-Powered Electrochemical Sensors Using Analyzed Liquid Sample as the Sole Energy Source

Many healthcare and environmental monitoring devices use electrochemical techniques to detect and quantify analytes. With sensors progressively becoming smaller-particularly in point-of-care (POC) devices and wearable platforms-it creates the opportunity to operate them using less energy than their predecessors. In fact, they may require so little power that can be extracted from the analyzed fluids themselves, for example, blood or sweat in case of physiological sensors and sources like river water in the case of environmental monitoring. Self-powered electrochemical sensors (SPES) can generate a response by utilizing the available chemical species in the analyzed liquid sample. Though SPESs generate relatively low power, capable devices can be engineered by combining suitable reactions, miniaturized cell designs, and effective sensing approaches for deciphering analyte information. This review details various such sensing and engineering approaches adopted in different categories of SPES systems that solely use the power available in liquid sample for their operation. Specifically, the categories discussed in this review cover enzyme-based systems, battery-based systems, and ion-selective electrode-based systems. The review details the benefits and drawbacks with these approaches, as well as prospects of and challenges to accomplishing them.

Point-of-care and self-testing for potassium: recent advances

Potassium is an important bodily electrolyte which is kept within tight limits in health. Many medical conditions as well as commonly-used drugs either raise or lower blood potassium levels, which can be dangerous or even fatal. For at-risk patients, frequent monitoring of potassium can improve safety and lifestyle, but conventional venous blood draws are inconvenient, don't provide a timely result and may be inaccurate. This review summarises current solutions and recent developments in point-of-care and self-testing potassium measurement technologies, which include devices for measurement of potassium in venous blood, devices for home blood collection and remote measurement, devices for rapid home measurement of potassium, wearable sensors for potassium in interstitial fluid, in sweat, in urine, as well as non-invasive potassium detection. We discuss the practical and clinical applicability of these technologies and provide future outlooks.

Direct Energy Transfer from a pH Glass Electrode to a Liquid Crystal Display

Self-powered sensors are attractive because the lack of a dedicated battery makes them environmentally friendly and allows them to be more easily miniaturized. Unfortunately, the development of self-powered potentiometric sensors is challenging because only very limited energy can be harvested from this measurement principle. For the first time, the potential of a high impedance glass pH electrode (130 M Ω) is shown here to be directly read out optically. This is accomplished by a liquid crystal display (LCD) as the electrochromic transducer, which changes its transmission upon imposing an external voltage in the range of 2-3 V. Importantly, owing to its low capacitance of about 50 pF, this process requires a very small transient charge on the order of 100 pC, which may be spontaneously imposable even across pH glass electrodes. For the LCD to be turned on, the cell voltage is boosted by additional Zn²⁺/Zn elements placed in series. The LCD is found to give a time-dependent absorbance decrease, which is mitigated by adding a high resistance element to attenuate the associated decay. The approach gives repeatable LCD absorbance values that allows one to directly visualize pH with a precision of about 0.01 pH units. The absorbance value depends inversely on pH in a much wider range (pH 1-13) than what is normally observed with optical sensors while based on the same underlying measurement as a potentiometric pH probe.

Self-Powered Potentiometric Sensors with Memory

Potentiometric sensors induce a spontaneous voltage that indicates ion activity in real time. We present here an advanced self-powered potentiometric sensor with memory. Specifically, the approach allows for one to record a deviation from the analyte's original concentration or determine whether the analyte concentration has surpassed a threshold in a predefined time interval. The sensor achieves this by harvesting energy in a capacitor and preserving it with the help of a diode. While the analyte concentration is allowed to return to an original value following a perturbation over time, this may not influence the sensor readout. To achieve the diode function, the sensor utilizes an additional pair of driving electrodes to move the potentiometric signal to a sufficiently high base voltage that is required for operating the diode placed in series with the capacitor and between the sensing probes. A single voltage measurement across the capacitor at the end of a chosen time interval is sufficient to reveal any altered ion activity occurring during that period. We demonstrate the applicability of the sensor to identify incurred pH changes in a river water sample during an interval of 2 h. This approach is promising for achieving deployable sensors to monitor ion activity relative to a defined threshold during a time interval with minimal electronic components in a self-powered design.

Self-Powered Electrochromic Readout of Potentiometric pH Electrodes

An absorbance-based colorimetric sensor array that is self-powered by an ion-selective electrode (ISE) in a short-circuited cell is presented. As the cell voltage is maintained at zero, the potential at the ISE serves as the power generator to directly transfer its power to a potential-dependent Prussian blue (PB) film in contact with an electrolyte solution in a separate detection compartment. This allows one to activate the color change of the PB film without the need for an external power supply. The potential of the PB detection element is optimized to change color between 50 and 250 mV (vs Ag/AgCl). Because the potential originates at the ISE, it is proportional to the ion activity in the sample in agreement with the Nernst equation. In this way, a higher cation activity in the sample generates a more positive potential, which enhances the PB absorbance that serves as the analytical signal. A self-powered optical sensor array coupled to poly(vinyl-chloride)-based pH electrodes based on two different ionophores is utilized here as a model. The measuring range is tuned chemically by varying the pH of the inner filling solution of each ISE, giving a measuring range from pH 2 to 10.5. As the optical sensor is driven by a potentiometric probe, the sensor output is independent of solution ionic strength. It is successfully applied for quantitative analysis in unmodified turbid/colored samples that included red wine, coke, coffee, baking soda, and antacid. The colorimetric output correlates well with the reference method, a calibrated pH electrode. Compared to earlier systems where the cell potential is dictated by an external power source, the PB film exhibits excellent reproducibility and a rapid response time of about 44 s.