Large scale and orientation-controllable nanotip structures on CuInS₂, Cu(In,Ga)S₂, CuInSe₂, and Cu(In,Ga)Se₂ by low energy ion beam bombardment process: growth and characterization

Sodium Incorporation for Performance Improvement of Solution-Processed Submicron CuIn(S,Se)2 Thin Film Solar Cells

Low-cost solution-processed CuIn(S,Se)2 (CISSe) has great potential for large-scale production of photovoltaics (PV). However, low power conversion efficiency caused by poor crystallinity is one of the main drawbacks compared to vacuum-processed CISSe solar cells. In this work, three strategies for sodium (Na) incorporation into solution-processed CISSe by soaking in sodium chloride (NaCl) aqueous-ethanol solution [1 molarity (M) for 10 minutes (min)], either prior to absorber deposition (pre-deposition treatment, Pre-DT), before selenization (pre-selenization treatment, Pre-ST), or after selenization (post-selenization treatment, PST) are researched. The Pre-ST CISSe solar cells achieve a better PV performance than those from the other two strategies of Na incorporation. For optimization, soaking times (5, 10, and 15 min) and NaCl concentrations (from 0.2 to 1.2 m) of the Pre-ST are researched. The highest efficiency achieved is 9.6% with an open-circuit voltage (Voc ) of 464.5 mV, a short-circuit current density (jsc ) of 33.4 mA cm-2 , and a fill factor (FF) of 62.0%. Compared to the reference CISSe solar cell, Voc , jsc , FF, and efficiency of the champion Pre-ST CISSe device are improved absolutely by 61.0 mV, 6.5 mA cm-2 , 9%, and 3.8%, respectively. Simultaneously, the open-circuit voltage deficit, the back contact barrier, and the bulk recombination are found to be reduced for Pre-ST CISSe.

An indoor light-activated 3D cone-shaped MoS2 bilayer-based NO gas sensor with PPb-level detection at room-temperature

Utilization of light to boost the performance of gas sensors allows us to operate sensor devices at room temperature. Here, we, for the first time, demonstrated an indoor light-activated 3D cone-shaped MoS2 bilayer-based NO gas sensor with ppb-level detection operated at room-temperature. Large-area cone-shaped (CS)-MoS2 bilayers were grown by depositing 2 nm-thick MoO3 layers on a 2'' three-dimensional (3D) cone-patterned sapphire substrate (CPSS) followed by a sulfurization process via chemical vapor deposition. Because the exposed area of MoS2 bilayers is increased by 30%, the CS-MoS2 gas sensor (GS) demonstrated excellent performance with a response of ∼470% and a fast response time of ∼25 s after exposure to 1 ppm of NO gas illuminated by ultraviolet (UV) light with a wavelength of 365 nm. Such extraordinary performance at room temperature is attributed to the enhanced light absorption because of the light scattering effect caused by the 3D configuration and photo-desorption induced by UV illumination. For NO concentrations ranging from 2 ppm down to 0.06 ppm, the CS-MoS2 GS demonstrated a stable sensing behavior with a high response and fast response time (470% and 25 s at 2 ppm NO) because of the light absorption enhanced by the 3D structure and photo-desorption under constant UV illumination. The CS-MoS2 GS exhibits a high sensitivity (∼189.2 R% ppm-1), allowing the detection of NO gas at 0.06 ppm in 130 s. In addition, the 3D cone-shaped structure prolonged the presence of sulfur vapor around MoO3, allowing MoO3 to react with sulfur completely. Furthermore, the CS-MoS2 GS using an indoor lighting to detect NO gas at room temperature was demonstrated for the first time where the CS-MoS2 GS exhibits a stable cycling behavior with a high response (165% at 1 ppm NO) in 50 s; for concentration as low as ∼0.06 ppm, the response of ∼75% in 150 s can be achieved.

Recent developments in the synthesis of nanostructured chalcopyrite materials and their applications: a review

Nanostructured chalcopyrites: synthesis and applications.