Highly Efficient Proton Conduction in the Metal-Organic Framework Material MFM-300(Cr)·SO4(H3O)2

Enhanced Proton Conduction in Metal-Organic Frameworks through Single-Crystal to Single-Crystal Transformation

In this work, an anionic framework Co-MOF (1) was elaborately constructed, which underwent single-crystal-to-single-crystal (SC-SC) transformation to produce 1-Cr and 1-Fe after immersion in a CrCl3 or FeCl3 solution. Despite the similar crystal structure, the significantly enhanced proton conductivities of 1-Cr and 1-Fe far exceed that of 1 at all humidity and temperature conditions. Even at 30 °C and 98% RH, the proton conductivity of 1-Cr and 1-Fe can reach up to high values of 1.49 × 10-2 and 6.39 × 10-3 S cm-1, respectively, surpassing that of 1 by over 5000 times under identical conditions. The partial alteration of the proton-conducting carriers from metal-water cluster [Co(H2O)6]·6H2O] (1) to metal-hydroxyl-water clusters [Cr(OH)4(H2O)2]·6H2O] (1-Cr) and [Fe(OH)4(H2O)2]·6H2O] (1-Fe) can be attributed for the above-mentioned enhanced performance. The introduction of hydroxyl by SC-SC transformation can establish interconnected proton conduction pathways within the proton channels, which greatly facilitate proton conduction, affording much lower activation energies (0.12 eV for 1-Cr, 0.18 eV for 1-Fe, and 0.28 eV for 1). This research demonstrated that SC-SC transformation not only achieved significantly improved proton conduction but also contributed to a deeper understanding of the structure-property relationships, providing new insights into the design of advanced materials with enhanced proton conductivity.

Proton-conducting copper-based MOFs for fuel cells

Metal-organic frameworks (MOFs) are emerging as promising alternatives for proton-conductive materials due to their high porosity, large surface area, stability, and relatively low cost. Among these, copper-based MOFs (Cu-MOFs) stand out with unique advantages, including open metal sites, variable valence states, and strongly electrophilic Cu centers. In this review, we discuss recent advances and developments in the use of Cu-MOFs as proton-conductive materials, with a particular focus on their application as proton exchange membranes (PEMs). We introduce the most common strategies employed to date and review the key features that have contributed to the construction of efficient proton transport pathways in Cu-MOFs. Additionally, we review PEMs fabricated via direct thin-film deposition or as mixed-matrix membranes (MMMs) incorporating Cu-MOF fillers. Finally, we address the challenges that must be overcome in the coming years to develop more robust Cu-MOFs and to create more efficient thin films and Cu-MOF-based MMMs.

Fabricating MOF-GO Composites by Modulating Graphene Oxide Content to Achieve Superprotonic Conductivity

Metal-organic frameworks (MOFs) have emerged as crucial materials for proton conductivity, especially in the context of the growing need for alternative energy sources. Enhancing the proton conductivity of MOFs has been a major focus with one effective approach involving the integration of MOFs with graphene oxide (GO) to form composite materials. In this study, Cr-MIL-101 MOF is selected, and its growth on GO sheets has been achieved through in situ crystallization, leading to the formation of MOF-GO composites with varying GO content, MIL-101/GO(x%), (x = 1%, 2%, and 5%). The oxygen functional groups on the 2D-GO layer e.g., carboxyl, hydroxyl, and epoxy groups improve both the acidity and hydrophilicity of the composite, which directly contributes to improved proton conductivity. All the composites, fabricated in this work, exhibit higher conductivity than that of the parent MOF due to the additional acidic functional groups introduced by GO. Among the different composites, the MIL-101/GO(2%) composite exhibits the highest proton conductivity, achieving superprotonic conductivity value of 0.105 S cm-1 at 80 °C and 98% relative humidity (RH). These results highlight the potential of MOF-GO composites for their application as nanofillers in proton exchange membranes for proton exchange membrane fuel cells (PEMFCs) and other energy-related technologies.

Synergistic effect promoting proton transport in metal-organic framework aerogels

One of the significant challenges encountered by metal-organic frameworks (MOFs) in proton conduction is their limited processability. In this study, we successfully synthesized UiO-66-COOH aerogel and UiO-66-2COOH aerogel, which exhibit high proton conductivities and remarkable temperature cycling stability in terms of performance and structural integrity.

Metal Effect on the Proton Conduction of Three Isostructural Metal-Organic Frameworks and Pseudo-Capacitance Behavior of the Cobalt Analogue

Three isostructural transition metal-organic frameworks, [M(bta)0.5(bpt)(H2O)2]·2H2O (M = Co (1), Ni (2), Zn (3), H4bta = 1,2,4,5-benzenetetracarboxylic acid, bpt = 4-amino-3,5-bis(4-pyridyl)-1,2,4-triazole), were successfully constructed using different metal cations. These frameworks exhibit a three-dimensional network structure with multiple coordinated and lattice water molecules within the framework, contributing to high stability and a rich hydrogen-bond network. Proton conduction studies revealed that, at 333 K and 98% relative humidity, the proton conductivities (σ) of MOFs 1-3 reached 1.42 × 10-2, 1.02 × 10-2, and 6.82 × 10-3 S cm-1, respectively. Compared to the proton conductivity of the initial ligands, the σ values of the complexes increased by 2 orders of magnitude, with the activation energies decreasing from 0.36 to 0.18 eV for 1, 0.09 eV for 2, and 0.12 eV for 3. An in-depth analysis of the correlation between different metal centers and proton conduction performance indicated that the varying coordination abilities of the metal cations and the water absorption capacities of the frameworks might account for the differences in conductivity. Additionally, the potential of 1 as a supercapacitor electrode material was assessed. 1 exhibited a specific capacitance of 61.13 F g-1 at a current density of 0.5 A g-1, with a capacitance retention of 82.4% after 5000 cycles, making it a promising candidate for energy storage applications.

Cooperative defect engineering and ligand modification in UiO-66 to achieve high proton conductivity

D-UiO-66-NIM with high proton conductivity has been synthesized through the dual strategy of defect engineering and ligand modification. Moreover, D-UiO-66-NIM exhibits good temperature cycling stability and durability in proton conductivity. This work has developed a new method to obtain efficient MOF-based proton conductors.

Vitrification-enabled enhancement of proton conductivity in hydrogen-bonded organic frameworks

Hydrogen-bonded organic frameworks (HOFs) are versatile materials with potential applications in proton conduction. Traditional approaches involve incorporating humidity control to address grain boundary challenges for proton conduction. This study finds vitrification as an alternative strategy to eliminate grain boundary effect in HOFs by rapidly melt quenching the kinetically stable HOF-SXU-8 to glassy state HOF-g. Notably, a remarkable enhancement in proton conductivity without humidity was achieved after vitrification, from 1.31 × 10-7 S cm-1 to 5.62× 10-2 S cm-1 at 100 °C. Long term stability test showed negligible performance degradation, and even at 30 °C, the proton conductivity remained at high level of 1.2 × 10-2 S cm-1. Molecule dynamics (MD) simulations and X-ray total scattering experiments reveal the HOF-g system is consisted of three kinds of clusters, i.e., 1,5-Naphthalenedisulfonic acid (1,5-NSA) anion clusters, N,N-dimethylformamide (DMF) molecule clusters, and H+-H2O clusters. In which, the H+ plays an important role to bridge these clusters and the high conductivity is mainly related to the H+ on H3O+. These findings provide valuable insights for optimizing HOFs, enabling efficient proton conduction, and advancing energy conversion and storage devices.

Imparting Stable and Ultrahigh Proton Conductivity to a Layered Rare Earth Hydroxide via Ion Exchange

Proton conductors are essential functional materials with a wide variety of potential applications in energy storage and conversion. In order to address the issues of low proton conductivity and poor stability in conventional proton conductors, a simple and valid ion-exchange method was proposed in this study for the introduction of stable and ultrahigh proton conductivity in layered rare earth hydroxides (LRHs). Test analyses by solid-state nuclear magnetic resonance, Fourier transform infrared spectroscopy, and powder X-ray diffraction revealed that the exchange of H2PO4- not only does not disrupt the layered structure of LRHs, but also creates more active proton sites and channels necessary for proton transport, thereby creating a high-performance proton conductor (LRH-H2PO4-). By utilizing this ion-exchange method, the proton conductivity of LRHs can be significantly enhanced from a low level to an ultrahigh level (>10-2 S·cm-1), while maintaining excellent long-term stability. Moreover, through methodically manipulating the guest ions and molecules housed within the interlayers of LRHs, a comprehensive explanation has been presented regarding the proficient mechanism of proton conduction in LRH-H2PO4-. As a result, this investigation presents a feasible and available approach for advancing proton conductor.

Comprehensive Understandings of Hydrogen Bond Chemistry in Aqueous Batteries

Aqueous batteries are emerging as highly promising contenders for large-scale grid energy storage because of uncomplicated assembly, exceptional safety, and cost-effectiveness. The unique aqueous electrolyte with a rich hydrogen bond (HB) environment inevitably has a significant impact on the electrode materials and electrochemical processes. While numerous reviews have focused on the materials design and assembly of aqueous batteries, the utilization of HB chemistry is overlooked. Herein, instead of merely compiling recent advancements, this review presents a comprehensive summary and analysis of the profound implication exerted by HB on all components of the aqueous batteries. Intricate links between the novel HB chemistry and various aqueous batteries are ingeniously constructed within the critical aspects, such as self-discharge, structural stability of electrode materials, pulverization, solvation structures, charge carrier diffusion, corrosion reactions, pH sensitivity, water splitting, polysulfides shuttle, and H2 S evolution. By adopting a vantage point that encompasses material design, binder and separator functionalization, electrolyte regulation, and HB optimization, a critical examination of the key factors that impede electrochemical performance in diverse aqueous batteries is conducted. Finally, insights are rendered properly based on HB chemistry, with the aim of propelling the advancement of state-of-the-art aqueous batteries.

A dual-functional cuprum coordination framework for high proton conduction and electrochemical dopamine detection

The present study selected 5, 5'-((6-(ethylamino)-1, 3, 5-triazine-2, 4-diyl) bis(azanediyl))diisophthalic acid (H4EATDIA) as ligand and an amino-functionalized cuprum-based MOF (EA-JUC-1000), successfully synthesized by microwave-assisted method, for proton conduction and dopamine sensing applications. In order to enhance the proton-conducting potential of EA-JUC-1000, the Brönsted acid (BA) encapsulated composites (BA@EA-JUC-1000) are dopped into chitosan (CS) to form a series of hybrid membranes (BA@EA-JUC-1000/CS). The impedance results display that the best proton conductivity of CF3SO3H@EA-JUC-1000/CS-8% reaches up to 1.23 × 10-3 S∙cm-1 at 338 K and ~ 98% RH, 2.6-fold than that of CS. Moreover, the EA-JUC-1000 is in-situ combined with reduced graphene oxide (rGO) (rGO/EA-JUC-1000), which makes EA-JUC-1000 have a wide detection range (0.1 ~ 500 μM) and a low limit of detection (50 nM), together with good anti-interference performance, reproducibility and repeatability. In addition, the electrochemical sensing method has been successfully applied to detect DA in bovine serum samples. The dual-functional MOF-based hybrid membrane and composites including proton conduction and DA sensing would provide an example of practical application for MOFs.

Ultrafast Proton Conduction in an Aqueous Electrolyte Confined in Adamantane-like Micropores of a Sulfonated, Aromatic Framework

Sulfonated, cross-linked porous polymers are promising frameworks for aqueous high-performance electrolyte-host systems for electrochemical energy storage and conversion. The systems offer high proton conductivities, excellent chemical and mechanical stabilities, and straightforward water management. However, little is known about mass transport mechanisms in such nanostructured hosts. We report on the synthesis and postsynthetic sulfonation of an aromatic framework (SPAF-2) with a 3D-interconnected nanoporosity and varying sulfonation degrees. Water adsorption produces the system SPAF-2H20. It features proton exchange capacities up to 6 mequiv g-1 and exceptional proton conductivities of about 1 S cm-1. Two contributions are essential for the highly efficient transport. First, the nanometer-sized pores link the charge transport to the diffusion of adsorbed water molecules, which is almost as fast as bulk water. Second, continuous exchange between interface-bound and mobile species enhances the conductivities at elevated temperatures. SPAF-2H20 showcases how to tailor nanostructured electrolyte-host systems with liquid-like conductivities.

A Multifunctional Co-Based Metal-Organic Framework as a Platform for Proton Conduction and Ni trophenols Reduction

The design and development of proton conduction materials for clean energy-related applications is obviously important and highly desired but challenging. An ultrastable cobalt-based metal-organic framework Co-MOF, formulated as [Co2(btzip)2(μ2-OH2)] (namely, LCUH-103, H2btzip = 4, 6-bis(triazol-1-yl)-isophthalic acid) had been successfully synthesized via the hydrothermal method. LCUH-103 exhibits a three-dimensional framework and a one-dimensional microporous channel structure with scu topology based on the binuclear metallic cluster {Co2}. LCUH-103 indicated excellent chemical and thermal stability; peculiarly, it can retain its entire framework in acid and alkali solutions with different pH values for 24 h. The excellent stability is a prerequisite for studying its proton conductivity, and its proton conductivity σ can reach up to 1.25 × 10-3 S·cm-1 at 80 °C and 100% relative humidity (RH). In order to enhance its proton conductivity, the proton-conducting material Im@LCUH-103 had been prepared by encapsulating imidazole molecules into the channels of LCUH-103. Im@LCUH-103 indicated an excellent proton conductivity of 3.18 × 10-2 S·cm-1 at 80 °C and 100% RH, which is 1 order of magnitude higher than that of original LCUH-103. The proton conduction mechanism was systematically studied by various detection means and theoretical calculations. Meanwhile, LCUH-103 is also an excellent carrier for palladium nanoparticles (Pd NPs) via a wetness impregnation strategy, and the nitrophenols (4/3/2-NP) reduction in aqueous solution by Pd@LCUH-103 indicated an outstanding conversion efficiency, high rate constant (k), and exceptional cycling stability. Specifically, the k value of 4-NP reduction by Pd@LCUH-103 is superior to many other reported catalysts, and its k value is as high as 1.34 min-1 and the cycling stability can reach up to 6 cycles. Notably, its turnover frequency (TOF) value is nearly 196.88 times more than that of Pd/C (wt 5%) in the reaction, indicating its excellent stability and catalytic activity.

Synthesis of Phosphovanadate-Based Porous Inorganic Frameworks with High Proton Conductivity

Materials with high proton conductivity have attracted significant attention for their wide-ranging applications in proton exchange membrane fuel cells. However, the design of new and efficient porous proton-conducting materials remains a challenging task. The structure-controllable and highly stable metal phosphates can be synthesized into layer or frame networks to provide proton transport capabilities. Herein, we have successfully synthesized three isomorphic metal phosphovanadates, namely, H2(C2H10N2)2[MII(H2O)2(VIVO)8(OH)4(PO4)4(HPO4)4] (C2H8N2 = 1,2-ethylenediamine; M = Co, Ni, and Cu), by the hydrothermal method employing ethylenediamine as a template. These pure inorganic open frameworks exhibit a cavity width ranging from 6.4 to 7.5 Å. Remarkably, the proton conductivity of compounds 1-3 can reach 1 × 10-2 S·cm-1 at 85 °C and 97% relative humidity (RH), and they can remain stable at high temperatures as well as long-term stability. This work provides a novel strategy for the development and design of porous proton-conducting materials.

Photomodulation of Proton Conductivity by Nitro-Nitroso Transformation in a Metal-Organic Framework

The design of a highly and photomodulated proton conductor is important for advanced potential applications in chemical sensors and bioionic functions. In this work, a metal-organic framework (MOF; Gd-NO2) with high proton conductivity is synthesized with a photosensitive ligand of 5-nitroisophthalic acid (BDC-NO2), and it provides remote-control photomodulated proton-conducting behavior. The proton conduction of Gd-NO2 reaches 3.66 × 10-2 S cm-1 at 98% relative humidity (RH) and 25 °C, while it decreases by ∼400 times after irradiation with a 355 nm laser. The newly generated and disappearing FT-IR characteristic peaks reveal that this photomodulated process is realized by the photoinduced transformation from BDC-NO2 to 5-nitroso-isophthalic acid (BDC-NO). According to density functional theory, the smaller electronegativity of the -NO group, the longer distance of the hydrogen bond between BDC-NO and H2O molecules, and the lower water adsorption energy of BDC-NO indicate that the irradiated sample possesses a poorer hydrophilicity and has difficulty forming rich hydrogen-bonded networks, which results in the remarkable decrease of proton conductivity.

MOF-Based Solid-State Proton Conductors Obtained by Intertwining Protic Ionic Liquid Polymers with MIL-101

Solid-state proton conductors based on the use of metal-organic framework (MOF) materials as proton exchange membranes are being investigated as alternatives to the current state of the art. This study reports a new family of proton conductors based on MIL-101 and protic ionic liquid polymers (PILPs) containing different anions. By first installing protic ionic liquid (PIL) monomers inside the hierarchical pores of a highly stable MOF, MIL-101, then carrying out polymerization in situ, a series of PILP@MIL-101 composites was synthesized. The resulting PILP@MIL-101 composites not only maintain the nanoporous cavities and water stability of MIL-101, but the intertwined PILPs provide a number of opportunities for much-improved proton transport compared to MIL-101. The PILP@MIL-101 composite with HSO4 - anions shows superprotonic conductivity (6.3 × 10-2  S cm-1 ) at 85 °C and 98% relative humidity. The mechanism of proton conduction is proposed. In addition, the structures of the PIL monomers were determined by single crystal X-ray analysis, which reveals many strong hydrogen bonding interactions with O/NH···O distances below 2.6 Å.

Ultra-fast Proton Conduction and Photocatalytic Water Splitting in a Pillared Metal-Organic Framework

Proton-exchange membrane fuel cells enable the portable utilization of hydrogen (H2) as an energy resource. Current electrolytic materials have limitation, and there is an urgent need to develop new materials showing especially high proton conductivity. Here, we report the ultra-fast proton conduction in a novel metal-organic framework, MFM-808, which adopts an unprecedented topology and a unique structure consisting of two-dimensional layers of {Zr6}-clusters. By replacing the bridging formate with sulfate ligands within {Zr6}-layers, the modified MFM-808-SO4 exhibits an exceptional proton conductivity of 0.21 S·cm-1 at 85 °C and 99% relative humidity. Modeling by molecular dynamics confirms that proton transfer is promoted by an efficient two-dimensional conducting network assembled by sulfate-{Zr6}-layers. MFM-808-SO4 also possesses excellent photocatalytic activity for water splitting to produce H2, paving a new pathway to achieve a renewable hydrogen-energy cycle.

Synthesis and In Situ Monitoring of Mechanochemical Preparation of Highly Proton Conductive Hydrogen-Bonded Metal Phosphonates

Crystalline porous materials are recognized as promising proton conductors for the proton exchange membrane (PEM) in fuel cell technology owing to their tunable framework structure. However, it is still a challenging bulk synthesis for real-world applications of these materials. Herein, we report the mechanochemical gram-scale synthesis of two isostructural metal hydrogen-bonded organic frameworks (MHOFs) of Co(II) and Ni(II) based on 1-hydroxyethylidenediphosphonic acid (HEDPH₄) with 2,2'-bipyridine (2,2'-bipy): Co(HEDPH₃)₂(2,2'-bipy)·H₂O (1) and Ni(HEDPH₃)₂(2,2'-bipy)·H₂O (2). In situ monitoring of the mechanochemical synthesis using different synchrotron-based techniques revealed a one-step mechanism - the starting materials are directly converted to the product. With the existence of extensive hydrogen bonds with amphiprotic uncoordinated phosphonate hydroxyl and oxygen atoms, both frameworks exhibited proton conduction in the range of 10^-4 S cm^-1 at room temperature under humid conditions. This study demonstrates the potential of green mechanosynthesis for bulk material preparation of framework-based solid-state proton conductors.

Sulfonic-Pendent Vinylene-Linked Covalent Organic Frameworks Enabling Benchmark Potential in Advanced Energy

Both proton exchange membrane fuel cells and uranium-based nuclear techniques represent two green and advanced energies. However, both of them still face some intractable scientific and industrial problems. For the former, established proton-conduction materials always suffer one or another defect such as low proton conductivity, high activation energy, bad durability, or just small-scale product; while for the later, there still lacks available adsorbent to selectively recover of UO₂ ²⁺ from concentrated nitric acid (>1 M) during the spent fuel reprocessing due to the deactivation of the adsorption site or the decomposition of adsorbent under such rigorous conditions. It is found that the above two issues can be well solved by the construction of sulfonic-pendent vinylene-linked covalent organic frameworks (COFs), since these COFs contain abundant sulfonic units for both intrinsic proton conduction and UO₂ ²⁺ capture through strong coordination fixation and vinylene linkage that enhances the stability up to 12 M nitric acid (one of the best materials surviving in 12 M HNO₃ ).

Anhydrous Superprotonic Conductivity in the Zirconium Acid Triphosphate ZrH5 (PO4 )3

The development of solid-state proton conductors with high proton conductivity at low temperatures is crucial for the implementation of hydrogen-based technologies for portable and automotive applications. Here, we report on the discovery of a new crystalline metal acid triphosphate, ZrH₅ (PO₄ )₃ (ZP3), which exhibits record-high proton conductivity of 0.5-3.1×10^-2  S cm^-1 in the range 25-110 °C in anhydrous conditions. This is the highest anhydrous proton conductivity ever reported in a crystalline solid proton conductor in the range 25-110 °C. Superprotonic conductivity in ZP3 is enabled by extended defective frustrated hydrogen bond chains, where the protons are dynamically disordered over two oxygen centers. The high proton conductivity and stability in anhydrous conditions make ZP3 an excellent candidate for innovative applications in fuel cells without the need for complex water management systems, and in other energy technologies requiring fast proton transfer.

Electronic Effect-Modulated Enhancements of Proton Conductivity in Porous Organic Polymers

We proposed a new strategy to maximize the density of acidic groups by modulating the electronic effects of the substituents for high-performance proton conductors. The conductivity of the sulfonated 1-MeL40-S with methyl group corresponds to 2.29×10^-1  S cm^-1 at 80 °C and 90 % relative humidity, remarkably an 22100-fold enhancement over the nonsulfonated 1-MeL40. 1-MeL40-S maintains long-term conductivity for one month. We confirm that this synthetic method is generalized to the extended version POPs, 2-MeL40-S and 3-MeL40-S. In particular, the conductivities of the POPs compete with those of top-level porous organic conductors. Moreover, the activation energy of the POPs is lower than that of the top-performing materials. This study demonstrates that systematic alteration of the electronic effects of substituents is a useful route to improve the conductivity and long-term durability of proton-conducting materials.

Two Stable Cd-MOFs as Dual-Functional Materials with Luminescent Sensing of Antibiotics and Proton Conduction

Construction and investigation of dual-functional metal-organic frameworks (MOFs) with luminescent sensing and proton conduction provide widespread applications in clean energy and environmental monitoring fields. By selecting a phosphonic acid ligand 4-pyridyl-CH₂N(CH₂PO₃H₂)₂ (H₄L) and coligand 2,2'-biimidazole (H₂biim), two cadmium-based MOFs [Cd_1.5(HL)(H₂biim)_0.5] (1) and (H₄biim)_0.5·[Cd₂(L)(H₂biim)Cl] (2) with different structures and properties have been hydrothermally synthesized by controlling reaction temperature. Based on the excellent thermal and chemical stabilities, and good luminescent stabilities in water solution, 1 and 2 can serve as luminescent sensors of chloramphenicol (CAP) with different quenching constant (K_SV) values and detection limits (LODs) in water, simulated environmental system, and real fish water system. Meanwhile, different sensing effects and possible sensing mechanisms are analyzed in detail. Moreover, 1 and 2 can also serve as good proton-conducting materials. The proton conductivities can reach up to 1.41 × 10^-4 S cm^-1 for 1 and 1.02 × 10^-3 S cm^-1 for 2 at 368 K and 95% relative humidity (RH). Among them, 2 shows better luminescent sensing and proton conduction performance than 1, which indicates that different crystal structures have a great impact on the properties of MOFs. Through the discussion of the relationship between structures and properties in detail, the possible reasons for the differences in properties are obtained, which can provide theoretical guidance for the rational design of this kind of dual-functional MOFs in the future.

Keeping Superprotonic Conductivity over a Wide Temperature Region via Sulfate Hopping Sites-Decorated Zirconium-Oxo Clusters

Metal-oxo clusters have emerged as advanced proton conductors with well-defined and tunable structures. Nevertheless, the exploitation of metal-oxo clusters with high and stable proton conductivity over a relatively wide temperature range still remains a great challenge. Herein, three sulfate groups decorated zirconium-oxo clusters (Zr₆ , Zr₁₈ , and Zr₇₀ ) as proton conductors are reported, which exhibit ultrahigh bulk proton conductivities of 1.71 × 10^-1 , 2.01 × 10^-2 , and 3.73 × 10^-2  S cm^-1 under 70 °C and 98% relative humidity (RH), respectively. Remarkably, Zr₆ and Zr₇₀ with multiple sulfate groups as proton hopping sites show ultralow activation energies of 0.22 and 0.18 eV, respectively, and stable bulk conductivities of >10^-2  S cm^-1 between 30 and 70 °C at 98% RH. Moreover, a time-dependent proton conductivity test reveals that the best performing Zr₆ can maintain high proton conductivity up to 15 h with negligible loss at 70 °C and 98% RH, representing one of the best crystalline cluster-based proton conducting materials.