Laser-Induced Photovoltage Transient Studies on Nanoporous TiO2 Electrodes

Conditions for diffusion-limited and reaction-limited recombination in nanostructured solar cells

The performance of Dye-sensitized solar cells (DSC) and related devices made of nanostructured semiconductors relies on a good charge separation, which in turn is achieved by favoring charge transport against recombination. Although both processes occur at very different time scales, hence ensuring good charge separation, in certain cases the kinetics of transport and recombination can be connected, either in a direct or an indirect way. In this work, the connection between electron transport and recombination in nanostructured solar cells is studied both theoretically and by Monte Carlo simulation. Calculations using the Multiple-Trapping model and a realistic trap distribution for nanostructured TiO2 show that for attempt-to-jump frequencies higher than 10(11)-10(13) Hz, the system adopts a reaction limited (RL) regime, with a lifetime which is effectively independent from the speed of the electrons in the transport level. For frequencies lower than those, and depending on the concentration of recombination centers in the material, the system enters a diffusion-limited regime (DL), where the lifetime increases if the speed of free electrons decreases. In general, the conditions for RL or DL recombination depend critically on the time scale difference between recombination kinetics and free-electron transport. Hence, if the former is too rapid with respect to the latter, the system is in the DL regime and total thermalization of carriers is not possible. In the opposite situation, a RL regime arises. Numerical data available in the literature, and the behavior of the lifetime with respect to (1) density of recombination centers and (2) probability of recombination at a given center, suggest that a typical DSC in operation stays in the RL regime with complete thermalization, although a transition to the DL regime may occur for electrolytes or hole conductors where recombination is especially rapid or where there is a larger dispersion of energies of electron acceptors.

Controlled seeding of laser deposited Ta:TiO2 nanobrushes and their performance as photoanode for dye sensitized solar cells

Hexagonal patterned indium tin oxide (ITO) with a height of 1.5 μm was fabricated on fluorinated SnO2 (FTO) substrate via nanoimprint lithography and pulsed laser deposition (PLD). Tantalum doped TiO2 was deposited on the patterned substrate by PLD. The film of Ta:TiO2 grew vertically and separately on the patterned ITO and formed a brush-like structure. Dye-sensitized solar cells with the Ta:TiO2 film deposited on the patterned substrate as well as flat FTO substrate for comparison were fabricated and tested. The device with the patterned substrate showed a 25% increase in short circuit current (Jsc) compared to the one with flat FTO substrate. Optical and photoelectrochemical characterization techniques were performed to investigate the improvement. The increase of Jsc was attributed to the enhancements of light absorption in the 600-750 nm range and collection of excited electrons by the brush-like structure and the patterned ITO, respectively.

Interpretation of optoelectronic transient and charge extraction measurements in dye-sensitized solar cells

Tools that assess the limitations of dye sensitized solar cells (DSSCs) made with new materials are critical for progress. Measuring the transient electrical signals (voltage or current) after optically perturbing a DSSC is an approach which can give information about electron concentration, transport and recombination. Here we describe the theory and practice of this class of optoelectronic measurements, illustrated with numerous examples. The measurements are interpreted with the multiple trapping continuum model which describes electrons in a semiconductor with an exponential distribution of trapping states. We review standard small perturbation photocurrent and photovoltage transients, and introduce the photovoltage time of flight measurement which allows the simultaneous derivation of both effective diffusion and recombination coefficients. We then consider the utility of large perturbation measurements such as charge extraction and the current interrupt technique for finding the internal charge and voltage within a device. Combining these measurements allows differences between DSSCs to be understood in terms such as electron collection efficiency, semiconductor conduction band edge shifts and recombination kinetics.

Simulation and measurement of complete dye sensitised solar cells: including the influence of trapping, electrolyte, oxidised dyes and light intensity on steady state and transient device behaviour

A numerical model of the dye sensitised solar cell (DSSC) is used to assess the importance of different loss pathways under various operational conditions. Based on our current understanding, the simulation describes the processes of injection, regeneration, recombination and transport of electrons, oxidised dye molecules and electrolyte within complete devices to give both time dependent and independent descriptions of performance. The results indicate that the flux of electrons lost from the nanocrystalline TiO(2) film is typically at least twice as large under conditions equivalent to 1 sun relative to dark conditions at matched TiO(2) charge concentration. This is in agreement with experimental observations (Barnes et al. Phys. Chem. Chem. Phys. [DOI: 10.1039/c0cp01855d]). The simulated difference in recombination flux is shown to be due to variation in the concentration profile of electron accepting species in the TiO(2) pores between light and dark conditions and to recombination to oxidised dyes in the light. The model is able to easily incorporate non-ideal behaviour of a cell such as the variation of open circuit potential with light intensity and non-first order recombination of conduction band electrons. The time dependent simulations, described by the multiple trapping model of electron transport and recombination, show good agreement with both small and large transient photocurrent and photovoltage measurements at open circuit, including photovoltage rise measurements. The simulation of photovoltage rise also suggests the possibility of assessing the interfacial resistance between the TiO(2) and substrate. When cells with a short diffusion length relative to film thickness were modelled, the simulated small perturbation photocurrent transients at short circuit (but not open circuit) yielded significantly higher effective diffusion coefficients than expected from the mean concentration of electrons and the electrolyte in the cell. This implies that transient measurements can overestimate the electron diffusion length in cells which have a low collection efficiency. The model should provide a useful general framework for exploring new cell descriptions, architectures and other factors influencing device performance.

A study of the dynamic properties of photo-induced charge carriers at nanoporous TiO(2)/conductive substrate interfaces by the transient photovoltage technique

Two interfaces with opposite orientations of the built-in electric field, nanoporous TiO(2) film/ FTO electrode and nanoporous TiO(2) film/semitransparent Pt substrate, were constructed. The separation and transport of photo-induced charge carriers in the two systems of nanoporous TiO(2)/conductive substrate were studied by the transient photovoltage technique. Various transient photovoltage responses were obtained when the laser beam was incident from the surface of the nanoporous TiO(2) film (top illumination) or the TiO(2)/substrate interface (bottom illumination). A linear and a logarithmic dependence of the photovoltage amplitude on the excitation level were observed for top illumination and bottom illumination, respectively. The results indicate that diffusion is the major way for the separation of charge carriers in the nanoporous TiO(2) film and that the excess carriers were separated by drift under the built-in electric field at the TiO(2)/substrate interfaces.

Stepped light-induced transient measurements of photocurrent and voltage in dye-sensitized solar cells: application for highly viscous electrolyte systems

To measure electron diffusion coefficients (D) and electron lifetimes (tau) of dye-sensitized solar cells (DSC), we introduced stepped light-induced transient measurements of photocurrent and voltage (SLIM-PCV), which can simplify the optical setup and reduce measurement time in comparison to conventional time-of-flight and frequency-modulated measurements. The method was applied to investigate the influence of the viscosity of a thermally stable high-boiling-point solvent on the energy conversion efficiency of DSCs. By systematic study of the influence of the viscosity, the species of cations as the counter charge of I(-)/I(3)(-), and the concentrations of electrolytes, we concluded that a lower dye cation reduction rate due to slower iodine diffusion is a limiting factor for a highly viscous electrolyte system. On the other hand, comparable values of D and increased values of tau were observed in a highly viscous electrolyte. By employing 0.5 M TBAI and 0.05 M I(2) in propylene carbonate, the efficiency of the DSC became comparable to that of a DSC using conventional electrolytes consisting of LiI, imidazolium iodide, and 4-tert-butylpyridine in methoxyacetonitrile. The simultaneous evaluation of D and tau through the appropriately simple measurement realizes fast optimization of the efficient and reliable DSC composed of thermally stable but often viscous electrolytes.

Novel Carboxylated Oligothiophenes as Sensitizers in Photoelectric Conversion Systems

Novel carboxylated oligothiophenes with different thiophene units were designed and synthesized as photosensitizers in dye-sensitized solar cells (DSSCs) for efficient opto-electric materials. The introduction of -COOH into thiophene molecules can lead to a red shift of UV-visible absorption, increase light-harvesting efficiency, and enhance photoinduced charge transport by forming efficient covalent bonds to the substrate surface. A red shift of the absorption spectrum of oligothiophene is also achieved by the increase in the number of thiophene units. The DSSCs based on the oligomers have excellent photovoltaic performances. Under 100 mW cm(-2) irradiation a short-circuit current of 10.57 mA cm(-2) and an overall energy conversion efficiency of 3.36 % is achieved when pentathiophene dicarboxylated acid was used as a sensitizer. The incident photo-to-current conversion efficiency (IPCE) has a maximum as high as 80 %. In addition, photovoltage and photocurrent transients show that slow charge recombination in DSSCs is important for efficient charge separation and excellent photoelectric conversion properties of the oligomers. These initial and promising results suggest that carboxylated oligothiophenes are efficient photosensitizers.

Role of Electrolytes on Charge Recombination in Dye-Sensitized TiO2 Solar Cell (1): The Case of Solar Cells Using the I-/I3- Redox Couple

Performance of dye-sensitized solar cells (DSCs) was investigated depending on the compositions of the electrolyte, i.e., the electrolyte with a different cation such as Li(+), tetra-n-butylammonium (TBA(+)), or 1,2-dimethyl-3-propylimidazolium (DMPIm(+)) in various concentrations, with and without 4-tert-butylpyridine (tBP), and with various concentrations of the I(-)/I(3)(-) redox couple. Current-voltage characteristics, electron lifetime, and electron diffusion coefficient were measured to clarify the effects of the constituents in the electrolyte on the charge recombination kinetics in the DSCs. Shorter lifetimes were found for the DSCs employing adsorptive cations of Li(+) and DMPIm(+) than for a less-adsorptive cation of TBA(+). On the other hand, the lifetimes were not influenced by the concentrations of the cations in the solutions. Under light irradiation, open-circuit voltages of DSCs decreased in the order of TBA(+)> DMPIm(+) > Li(+), and also decreased with the increase of [Li(+)]. The decreases of open-circuit voltage (V(oc)) were attributed to the positive shift of the TiO(2) conduction band potential (CBP) by the surface adsorption of DMPIm(+) and Li(+). These results suggest that the difference of the free energies between that of the electrons in the TiO(2) and of I(3)(-) has little influence on the electron lifetimes in the DSCs. The shorter lifetime with the adsorptive cations was interpreted with the thickness of the electrical double layer formed by the cations, and the concentration of I(3)(-) in the layer, i.e., TBA(+) formed thicker double layer resulting in lower concentration of I(3)(-) on the surface of the TiO(2). The addition of 4-tert-butylpyridine (tBP) in the presence of Li(+) or TBA(+) showed no significant influence on the lifetime. The increase of V(oc) by the addition of tBP into the electrolyte containing Li(+) and the I(-)/I(3)(-) redox couple was mainly attributed to the shift of the CBP back to the negative potential by reducing the amount of adsorbed Li cations.