Influence of test protocol in determining the blood response to model polymers

In vitro thrombogenicity investigation of new water-dispersible polyurethane anionomers bearing carboxylate groups

New segmented polyurethane (PU) anionomers based on hydroxytelechelic polybutadiene were synthesized via an aqueous dispersion process. Incorporation of carboxylic groups was achieved using thioacids of different length. Surface properties were investigated by mean of water absorption analysis and static contact-angle measurements using water, diiodomethane, formamide and ethylene glycol. Blood compatibility of the PUs was evaluated by in vitro adhesion assays using 111In-radiolabeled platelet-rich plasma and [125I]fibrinogen. Morphology of the adhered platelets was examined by scanning electron microscopy (SEM). Results were compared to two biomedical-grade PUs, namely Pellethane and Tecoflex. Insertion of carboxylic groups increased surface hydrophilicity and limited water uptake ( < 8% for an ion content of 5% by weight). Surface energy of all synthesized PUs was between 40 and 45 mJ/m2. Platelet adhesion and fibrinogen adsorption on the PU anionomer surfaces were affected as a function to the increase of graft length; thiopropionic was the most haemocompatible, followed by thiosuccinic and then thioglycolic acid. SEM analyses of all ionic PU samples exhibited low platelet adhesion to surfaces with no morphological modification. In conclusion, increased hydrophily, dynamic mobility and charge repulsion are synergistic key factors for enhanced haemocompatibility.

Characterization of In Vitro Hemostatic Peptide Effects by Thromboelastography

In this study, we validated a thromboelastography (TEG) method to evaluate the hemostatic effects of 3 peptides. The first peptide is an ideal amphipathic peptide composed of 22 leucine and lysine in a ratio of 2:1. At a very low concentration, the peptide had a procoagulant effect shown by decreases in reaction time (R) and coagulation time (K) but was impaired by a decrease in maximum amplitude (MA). At higher concentrations, the peptide had an anticoagulant effect. The α angle was minimally affected by the peptide. The second peptide is melittin derived from bee venom. Melittin showed procoagulant effects reflected by a decrease in clotting time but led to lower MA. The third peptide derived from fibrinogen γ chain promoted hemostasis only at an optimal concentration and became anticoagulant at a higher concentration. The hemostatic mechanisms of each peptide were discussed. Our study would facilitate further development of peptides for either hemorrhage control or thrombosis treatment.

Decreased material-activation of the complement system using low-energy plasma polymerized poly(vinyl pyrrolidone) coatings

In the current study we investigate the activation of blood complement on medical device silicone rubber and present a plasma polymerized vinyl pyrrolidone (ppVP) coating which strongly decreases surface-activation of the blood complement system. We show that uncoated silicone and polystyrene are both potent activators of the complement system, measured both as activated, deposited C3b and quantifying fluid-phase release of the cleavage fragment C3c. The ppVP coated silicone exhibits approximately 90% reduced complement activation compared to untreated silicone. Quartz crystal microbalance with dissipation (QCM-D) measurements show relatively strong adsorption of blood proteins including native C3 to the ppVP surface, indicating that reduction of complement activation on ppVP is neither a result of low protein adsorption nor lower direct C3-binding, and is therefore possibly a consequence of differences in the adsorbed protein layer composition. The alternative and classical complement pathways are barely detectable on ppVP while the lectin pathway through MBL/ficolin-2 deposition remains active on ppVP suggesting this pathway is responsible for the remaining subtle activation on the ppVP coated surface. The ppVP surface is furthermore characterized physically and chemically using scanning electron microscopy (SEM), x-ray photoelectron spectroscopy (XPS) and Fourier transform infrared (FTIR), which indicates preservation of chemical functionality by the applied plasma process. Overall, the ppVP coating shows a potential for increasing complement-compatibility of blood-contacting devices.

Are aortic endograft prostheses fully hemo-compatible? A dielectric spectroscopy investigation of the electrical alterations induced on erythrocyte cell membranes

In this paper we present a new approach directed to ascertain the full hemo-compatibility of aortic endograft prostheses based on the measurement of the passive electrical parameters of the erythrocyte cell membrane. The red blood cell membrane, from an electric point of view, is characterized by an electrical permittivity, (s), which takes into account the structural charged organization of the lipid double layer, and by the electrical conductivity, sigma(s), which accounts for the ionic transport processes across the membrane. These parameters can be easily measured by means of a radiowave dielectric spectroscopy technique, analyzing the dependence of the electrical impedance of an erythrocyte suspension on the frequency of the applied electric field. In this preliminary report, we investigate the alterations induced, at a membrane level, by two different devices commonly employed for endovascular abdominal aortic aneurysm exclusion, i.e., Excluder and Zenith devices, implanted in ten patients. We observe, in all the cases investigated, a statistically significant increase of both the permittivity (s) and electrical conductivity sigma(s) of the erythrocyte membrane upon the prosthesis implant, this increase being higher than about 20% of the un-treated values. Moreover, these alterations remain roughly unaffected 30 days after surgery. These findings suggest that a complete hemo-compatibility of these prostheses is lacking, even if the observed alterations may not have a clinical relevance.

Surface-attached PEO in the form of activated pluronic with immobilized factor H reduces both coagulation and complement activation in a whole-blood model

In the present work we have bound Pluronic, a class of triblock copolymers consisting of a block of polypropylene oxide (PPO) surrounded on each side by polyethylene oxide (PEO) blocks, to polystyrene surfaces and investigated the thrombogenicity and complement activation of this construct upon exposure to whole blood. The surface was highly inert towards coagulation, unfortunately at the expense of increased complement activation. We, therefore, as an alternative approach, used End-Group Activated Pluronic to conjugate factor H, a regulator of complement activation (RCA), to the surface. The bound factor H did not detach from the surface upon incubation with human serum. Furthermore, factor H bound in a physiological conformation could to a significant degree attenuate complement activation at the Pluronic surface. Thus, we have created a hybrid surface in which the coagulation-inert properties of the original Pluronic are supplemented with a specific complement-inhibitory effect. Medical device technology includes numerous potential applications for crosslinkers that are capable of specifically binding biomolecules to surfaces with retained activity. These applications include coupling of functional biomolecules to biomedical devices such as stents and grafts. The biomolecule may be an RCA, antibody, or other beneficial ligand.

Hemocompatibilty of new ionic polyurethanes: influence of carboxylic group insertion modes

New segmented polyurethane (PU) anionomers based on hydroxytelechelic polybutadiene (HTPB) were synthesized via two environment-friendly chemical routes. The effects of carboxylic content and ion incorporation mode on the surface properties were investigated by mean of water absorption analysis and static contact angle measurements using water, diiodomethane, formamide and ethylene glycol. Blood compatibility of the PUs was evaluated by in vitro adhesion assay using 111In-radiolabeled platelet rich plasma and 125I-fibrinogen. The morphology of platelet adhesion was also observed by scanning electron microscopy (SEM). Results were compared with a biomedical-grade PU, Pellethane. Insertion of the carboxylic groups on the soft segments (S-alpha series), using thioglycolic acid (TGA), increases surface hydrophilicity, limits water uptake (5%, for an ion content of 3.6 wt%), and reduces platelet adhesion and fibrinogen adsorption on the PUs' surfaces. In contrast, the classical insertion onto the hard segment (H-alpha series), using dimethylolpropionate (DMPA) as chain extender, leads to high water uptake (18%, for an ion content of 3.6 wt%) and promotes platelet and fibrinogen adhesion. SEM analyses of the non-ionic PUs exhibited surfaces with adhered platelets which underwent morphological modification. Similarly, the H-alpha ionic PUs show adherent and activated platelets. On the contrary, no platelet morphology changes were observed on the S-alpha ionic surfaces. In conclusion, insertion of carboxyl groups on the soft segments of PUs reduces their thrombogenicity.