Shape memory polymer resonators as highly sensitive uncooled infrared detectors

Sub-millikelvin-resolved superconducting nanowire single-photon detector operates with sub-pW infrared radiation power

The noise equivalent temperature difference (NETD) indicates the minimum temperature difference resolvable by using an infrared detector. The lower the NETD, the better the sensor can register small temperature differences. In this work, we proposed a strategy to achieve a high temperature resolution using a superconducting nanowire single-photon detector (SNSPD) with ultra-high sensitivity. We deduced the model for calculating the NETD of a photon-counting-type detector and applied it to our SNSPD-based set-up. Experimentally, we obtained an NETD as low as 0.65 mK, which is limited by the background radiation of the environment, and the required infrared radiation power is calculated to be <1 pW. Furthermore, the intrinsic NETD of this SNSPD is estimated to be <0.1 mK. This work demonstrated a sub-mK temperature resolution when using the SNSPD, paving the way for future remote infrared thermal imaging with high temperature resolution.

Terahertz communication: detection and signal processing

The development of 6 G networks has promoted related research based on terahertz communication. As submillimeter radiation, signal transportation via terahertz waves has several superior properties, including non-ionizing and easy penetration of non-metallic materials. This paper provides an overview of different terahertz detectors based on various mechanisms. Additionally, the detailed fabrication process, structural design, and the improvement strategies are summarized. Following that, it is essential and necessary to prevent the practical signal from noise, and methods such as wavelet transform, UM-MIMO and decoding have been introduced. This paper highlights the detection process of the terahertz wave system and signal processing after the collection of signal data.

Mode localization in plasmonic optomechanical resonators for ultrasensitive infrared sensing

Uncooled infrared thermal detectors are gaining increasing attention owing to their ability to operate at room-temperature and their low cost. This study proposes a plasmonic optomechanical resonator for ultrasensitive long-wave infrared wave sensing based on mode localization mechanism. The mode-localized effect confines the plasmonic energy in the resonators and induces a significant modal amplitude shift through infrared irradiation, thus achieving highly sensitive detection. The results show that the detection sensitivity can reach 1.304 /mW, which is three-order improvement compared to the frequency-shift sensing metrics. The research provides a new approach to further improve the detection sensitivity of uncooled infrared sensors.

Thermal spiral inductor using 3D printed shape memory kirigami

Spiral inductors are required to realise high inductance in radio frequency (RF) circuits. Although their fabrication by using micro-electrical-mechanical systems, thin films, actuators, etc., has received considerable research attention, current approaches are both complex and expensive. In this study, we designed and fabricated a thermal spiral inductor by using a three-dimensional (3D) printed shape-memory polymer (SMP). The proposed inductor was inspired by kirigami geometry whereby a two-dimensional (2D) planar geometric shape could be transformed into a 3D spiral one to change the inductance by heating and manually transform. Mechanical and electromagnetic analyses of the spiral inductor design was conducted. Hence, in contrast with the current processes used to manufacture spiral inductors, ours can be realised via a single facile fabrication step.

Study of MXene Ti3C2Tx quantum dot thin film on quartz bulk acoustic wave uncooled infrared sensors

The infrared absorption efficiency is essential for an infrared sensor. We propose a quartz bulk acoustic wave (BAW) uncooled infrared sensor coated with MXene quantum dot film. The infrared detection is realized by measuring the resonant frequency of a Y-cut quartz BAW sensitive unit. An infrared sensor is fabricated by MEMS process, then the MXene quantum dot film is coated through the spin coating technology. The mechanism of infrared absorption enhancement is analyzed. Test results show that after coating the film, the responsivity (R) of the sensor increased by nearly 41% at a wavelength of 830nm, from 10.88MHz/W to 15.28 MHz/W. The quartz BAW infrared sensor combined with MXene quantum dots film has the potential of high-performance infrared detection.

Application and Development of Shape Memory Micro/Nano Patterns

Shape memory polymers (SMPs) are a class of smart materials that change shape when stimulated by environmental stimuli. Different from the shape memory effect at the macro level, the introduction of micro-patterning technology into SMPs strengthens the exploration of the shape memory effect at the micro/nano level. The emergence of shape memory micro/nano patterns provides a new direction for the future development of smart polymers, and their applications in the fields of biomedicine/textile/micro-optics/adhesives show huge potential. In this review, the authors introduce the types of shape memory micro/nano patterns, summarize the preparation methods, then explore the imminent and potential applications in various fields. In the end, their shortcomings and future development direction are also proposed.

Intrinsic carbon nanotube liquid crystalline elastomer photoactuators for high-definition biomechanics

Photoresponsive soft actuators with the unique merits of flexibility, contactless operation, and remote control have huge potential in technological applications of bionic robotics and biomedical devices. Herein, a facile strategy was proposed to prepare an intrinsically-photoresponsive elastomer by chemically grafting carbon nanotubes (CNTs) into a thermally-sensitive liquid-crystalline elastomer (LCE) network. Highly effective dispersion and nematic orientation of CNTs in the intrinsic LCE matrix were observed to yield anchoring energies ranging from 1.65 × 10^-5 J m^-2 to 5.49 × 10^-7 J m^-2, which significantly enhanced the mechanical and photothermal properties of the photoresponsive elastomer. When embedding an ultralow loading of CNTs (0.1 wt%), the tensile strength of the LCE increased by 420% to 13.89 MPa (||) and 530% to 3.94 MPa (⊥) and exhibited a stable response to repeated alternating cooling and heating cycles, as well as repeated UV and infrared irradiation. Furthermore, the shape transformation, locomotion, and photo-actuation capabilities allow the CNT/LCE actuator to be applied in high-definition biomechanical applications, such as phototactic flowers, serpentine robots and artificial muscles. This design strategy may provide a promising method to manufacture high-precision, remote-control smart devices.

Moisture-induced autonomous surface potential oscillations for energy harvesting

A variety of autonomous oscillations in nature such as heartbeats and some biochemical reactions have been widely studied and utilized for applications in the fields of bioscience and engineering. Here, we report a unique phenomenon of moisture-induced electrical potential oscillations on polymers, poly([2-(methacryloyloxy)ethyl] dimethyl-(3-sulfopropyl) ammonium hydroxide-co-acrylic acid), during the diffusion of water molecules. Chemical reactions are modeled by kinetic simulations while system dynamic equations and the stability matrix are analyzed to show the chaotic nature of the system which oscillates with hidden attractors to induce the autonomous surface potential oscillation. Using moisture in the ambient environment as the activation source, this self-excited chemoelectrical reaction could have broad influences and usages in surface-reaction based devices and systems. As a proof-of-concept demonstration, an energy harvester is constructed and achieved the continuous energy production for more than 15,000 seconds with an energy density of 16.8 mJ/cm2. A 2-Volts output voltage has been produced to power a liquid crystal display toward practical applications with five energy harvesters connected in series.

Plasmon mediated spectrally selective and sensitivity-enhanced uncooled near-infrared detector

Here, we present a high performance uncooled near-infrared (NIR) detector comprising of a giga hertz (GHz) solidly mounted resonator (SMR) and gold nanorods (GNRs) arrays. By coupling the localized surface plasmon resonances of GNRs, the resonator system exhibits optimized optical response to vis-NIR region. Both simulation and experiments demonstrate the hybrid GNRs-SMR exhibit significantly enhanced optical responsive sensitivity of NIR, the tunable aspect ratios (AR) of GNRs enable resonator respond sensitively to selected light. Specially, taking advantage of the acoustofluidic effect of SMR, the GNRs can be controllably and precisely modified on the microchip surface in an ultra-short time, which addresses one of the most fundamental challenges in the localized functionalization of micro/nano scale surface. The presented work opens new directions in development of novel miniaturized, tunable NIR detector.

A Review of Shape Memory Polymers and Composites: Mechanisms, Materials, and Applications

Over the past decades, interest in shape memory polymers (SMPs) has persisted, and immense efforts have been dedicated to developing SMPs and their multifunctional composites. As a class of stimuli-responsive polymers, SMPs can return to their initial shape from a programmed temporary shape under external stimuli, such as light, heat, magnetism, and electricity. The introduction of functional materials and nanostructures results in shape memory polymer composites (SMPCs) with large recoverable deformation, enhanced mechanical properties, and controllable remote actuation. Because of these unique features, SMPCs have a broad application prospect in many fields covering aerospace engineering, biomedical devices, flexible electronics, soft robotics, shape memory arrays, and 4D printing. Herein, a comprehensive analysis of the shape recovery mechanisms, multifunctionality, applications, and recent advances in SMPs and SMPCs is presented. Specifically, the combination of functional, reversible, multiple, and controllable shape recovery processes is discussed. Further, established products from such materials are highlighted. Finally, potential directions for the future advancement of SMPs are proposed.

Solid-state membranes formed on natural menisci

We present a method to create robust, nanoscale solid-state membranes using the natural shape of a liquid meniscus as a template. A narrow, open channel is etched into a silicon substrate and then a photoresist polymer is introduced into the channel through spontaneous capillary action. The natural concave meniscus formed by the polymer is then covered by a thin chemical vapor deposited membrane. The polymer is removed by sacrificial etching, leaving behind a suspended membrane. Membranes as large as 20 μm by 9 mm can be fabricated with a thickness as low as 50 nm.

Temperature-Modulated Micromechanical Thermal Analysis with Microstring Resonators Detects Multiple Coherent Features of Small Molecule Glass Transition

Micromechanical Thermal Analysis utilizes microstring resonators to analyze a minimum amount of sample to obtain both the thermal and mechanical responses of the sample during a heating ramp. We introduce a modulated setup by superimposing a sinusoidal heating on the linear heating and implementing a post-measurement data deconvolution process. This setup is utilized to take a closer look at the glass transition as an important fundamental feature of amorphous matter with relations to the processing and physical stability of small molecule drugs. With an additionally developed image and qualitative mode shape analysis, we are able to separate distinct features of the glass transition process and explain a previously observed two-fold change in resonance frequency. The results from this setup indicate the detection of initial relaxation to viscous flow onset as well as differences in mode responsivity and possible changes in the primary resonance mode of the string resonators. The modulated setup is helpful to distinguish these processes during the glass transition with varying responses in the frequency and quality factor domain and offers a more robust way to detect the glass transition compared to previously developed methods. Furthermore, practical and theoretical considerations are discussed when performing measurements on string resonators (and comparable emerging analytical techniques) for physicochemical characterization.