Distinctive features of diffusion-controlled radiation defect recombination in stoichiometric magnesium aluminate spinel single crystals and transparent polycrystalline ceramics

Optical Characteristics of MgAl2O4 Single Crystals Irradiated by 220 MeV Xe Ions

In In this study, the optical properties of magnesium-aluminate spinel were examined after being irradiated with 220 MeV Xe ions. The research aimed to simulate the impact of nuclear fuel fission fragments on the material. The following measurements were taken during the experiments: transmission spectra in the IR region (190-7000) nm, optical absorption spectra in the range (1.2-6.5) eV, and Raman spectra were measured along the depth of ion penetration from the surface to 30 µm. A peak with a broad shape at approximately 5.3 eV can be observed in the optical absorption spectrum of irradiated spinel crystals. This band is linked to the electronic color centers of F+ and F. Meanwhile, the band with a maximum at ~(3-4) eV is attributed to hole color centers. Apart from the typical Raman modes of an unirradiated crystal, additional modes, A1g* (720 cm-1), and Eg* (385 cm-1), manifested mainly as an asymmetric shoulder of the main Eg mode, are also observed. In addition, the Raman spectroscopy method showed that the greatest disordering of crystallinity occurs in the near-surface layer up to 4 μm thick. At the same time, Raman scattering spectroscopy is sensitive to structural changes almost up to the simulated value of the modified layer, which is an excellent express method for certifying the structural properties of crystals modified by swift heavy ions.

Enhanced Properties of Tailored Alumina-Magnesia-Based Dry Ramming Mixes by Calcium Magnesium Aluminate (CMA)

To achieve the goal of "dual-carbon", induction furnaces with high efficiency and energy-saving advantages are paid more attention in the foundry and metallurgy industries. The service life and safety of induction furnaces strongly depended on the lining because expansion and forward sintering could result in the erosion and slag resistance of the lining. Focusing on the tailoring properties of alumina-magnesia-based dry ramming mixes, calcined magnesia particles were replaced with the novel multi-component materials of calcium magnesium aluminate (CaO-MgO-Al₂O₃, CMA) with a size of 200 mesh. Properties such as the bulk density, apparent porosity, strength, and slag corrosion resistance of alumina-magnesia-based dry ramming mix containing CMA were evaluated contrastively. The results demonstrate that the penetration index of manganese-bearing slag in dry ramming mixes first decreased and then slightly increased with the addition of CMA. Meanwhile, the permanent linear change in dry ramming mixes was gradually reduced. When the addition of CMA reached 4 wt%, the strength of the dry ramming mixes was slightly greater than the reference, and the slag penetration index was just 75% of the latter.

Formation of TiB2-MgAl2O4 Composites by SHS Metallurgy

TiB₂-MgAl₂O₄ composites were fabricated by combustion synthesis involving metallothermic reduction reactions. Thermite reagents contained Al and Mg as dual reductants and TiO₂ or B₂O₃ as the oxidant. The reactant mixtures also comprised elemental Ti and boron, as well as a small amount of Al₂O₃ or MgO to serve as the combustion moderator. Four reaction systems were conducted and all of them were exothermic enough to proceed in the mode of self-propagating high-temperature synthesis (SHS). The reaction based on B₂O₃/Al/Mg thermite and diluted with MgO was the most exothermic, while that containing TiO₂/Al/Mg thermite and Al₂O₃ as the diluent was the least. Depending on different thermites and diluents, the combustion front temperatures in a range from 1320 to 1720 °C, and combustion wave velocity from 3.9 to 5.7 mm/s were measured. The XRD spectra confirmed in situ formation of TiB₂ and MgAl₂O₄. It is believed that MgAl₂O₄ was synthesized through a combination reaction between Al₂O₃ and MgO, both of which can be totally or partially produced from the metallothermic reduction of B₂O₃ or TiO₂. The microstructure of the TiB₂-MgAl₂O₄ composite exhibited fine TiB₂ crystals surrounded by large densified MgAl₂O₄ grains. This study demonstrated an energy-saving and efficient route for fabricating MgAl₂O₄-containing composites.

Ni Porous Preforms Compacted with Al2O3 Particles and Al Binding Agent

This work presents an energy-efficient, cheap, and rapid production method of a metal-ceramic preform with open porosity suitable for liquid metal infiltration and filtration applications. It is based on cold isostatic pressing of a mixture of relatively hard Ni and Al₂O₃ powders with the addition of small amount of Al powders, acting as a binding agent. Open porosity is primarily controlled by Al₂O₃ particles partially separating Ni particles from mutual contacts. Cold isostatic pressed green compacts were subjected to thermal oxidation by heating in air to 600 °C, 700 °C, and 800 °C. The weight gain and open porosity of oxidized compacts were examined. The chemical composition and microstructure were analyzed by SEM-EDS and XRD techniques. The stability of preforms and the effect of thermal cycling on the open porosity were tested by thermal cycling in an inert Ar atmosphere in the temperature range up to 800 °C. It appeared that, in addition to NiO being an expected product of oxidation, Ni aluminides and spinel particles also played an important role in inter-particle bonding formation. Ni-NiO porous composites resist chemical corrosion and exhibit structural and chemical stability at higher temperatures and admixed Al₂O₃ particles do not deteriorate them. After subsequent infiltration with Al, it can offer a lower density than other materials, which could result in lower energy consumption, which is highly needed in industries such as the automotive industry.

Magnetic Behavior of Virgin and Lithiated NiFe2O4 Nanoparticles

A series of virgin and lithia-doped Ni ferrites was synthesized using egg-white-mediated combustion. Characterization of the investigated ferrites was performed using several techniques, specifically, X-ray Powder Diffraction (XRD), Fourier-transform infrared spectroscopy (FTIR), and High-resolution transmission electron microscopy (HRTEM). XRD-based structural parameters were determined. A closer look at these characteristics reveals that lithia doping enhanced the nickel ferrite lattice constant (a), unit cell volume (V), stress (ε), microstrain (σ), and dislocation density (δ). It also enhanced the separation between magnetic ions (LA and LB), ionic radii (rA, rB), and bond lengths (A-O and B-O) between tetrahedral (A) and octahedral (B) locations. Furthermore, it enhanced the X-ray density (Dx) and crystallite size (d) of random spinel nickel ferrite displaying opposing patterns of behavior. FTIR-based functional groups of random spinel nickel ferrite were determined. HRTEM-based morphological properties of the synthesized ferrite were investigated. These characteristics of NiFe2O4 particles, such as their size, shape, and crystallinity, demonstrate that these manufactured particles are present at the nanoscale and that lithia doping caused shape modification of the particles. Additionally, the prepared ferrite’s surface area and total pore volume marginally increased after being treated with lithia, depending on the visibility of the grain boundaries. Last, but not least, as the dopant content was increased through a variety of methods, the magnetization of virgin nickel ferrite fell with a corresponding increase in coercivity. Uniaxial anisotropy, rather than cubic anisotropy, and antisite and cation excess defects developed in virgin and lithia-doped nickel ferrites because the squareness ratio (Mr/Ms) was less than 0.5. Small squareness values strongly recommend using the assessed ferrites in high-frequency applications.

Fabrication and Characterization of W-Substituted ZnFe2O4 for Gas Sensing Applications

A sol–gel technique was successfully employed in creating pure and W-substituted zinc ferrite, with nominal compositions of ZnFe2−2xWxO4 (0.0 ≤ x ≤ 0.15). For the purposes of investigating the physical and chemical properties of the generated powders, several analytical techniques were used. In TEM images of all the compositions, mixed-shaped particles (cubic, spherical, and hexagonal) were observed. The crystallite size decreases from 82 nm (x = 0.0) to 32 nm (x = 0.15) with an increase in the W doping contents in the ZnFe2O4 lattice. The microstrain increases with increasing W doping content. Furthermore, the surface area of pure ZnFe2O4, 0.05 W-ZnFe2O4, 0.10 W-ZnFe2O4, and 0.15 W-ZnFe2O4 NPs were calculated as being 121.5, 129.1, 134.4 and 143.2 m2 g−1, respectively, with a mesoporous pore structure for all ferrite samples. The calculated BJH pore size distribution was within the range of 160 to 205 Å. All W-doped ZnFe2O4 samples show H-M loops with paramagnetic characteristics. The magnetization (M) directly increases by increasing the applied field (H) without achieving saturation up to 20 kA/m. For comparison, the magnetization at 20 kA/m gradually decreases with increasing W doping content. Among all the synthesized samples, the 0.15 W-ZnFe2O4 NPs demonstrated the highest sensitivity towards acetone gas at 350 °C.

Fabrication of Highly Transparent Y2O3 Ceramics via Colloidal Processing Using ZrO2-Coated Y2O3 Nanoparticles

An easy approach is described for the preparation of ZrO2-coated Y2O3 nanopowder from a solution of zirconium nitrate with commercial Y2O3 nanopowder. The evolution process of the ZrO2 coating layer upon calcination, such as the phase and microstructure of the particles’ surface, was studied. Calcination of the powder at 700 °C resulted in ZrO2-coated Y2O3 nanopowder. The rheological properties of the suspensions of ZrO2-coated Y2O3 powders were studied. A well-dispersed suspension with a solid loading of 35.0 vol% using ZrO2-coated Y2O3 nanopowder was obtained. The consolidated green body obtained by the centrifugal casting method showed improved homogeneity with a relative density of 50.2%. Transparent ceramic with high transparency and an average grain size of 1.7 µm was obtained by presintering at 1500 °C for 16 h in air, followed by post-HIP at 1550 °C for 2 h under 200 MPa pressure. The in-line transmittance at the wavelength of 1100 nm (1.0 mm thick) reached 81.4%, close to the theoretical transmittance of Y2O3 crystal.

Ion-Track Template Synthesis and Characterization of ZnSeO3 Nanocrystals

ZnSeO3 nanocrystals with an orthorhombic structure were synthesized by electrochemical and chemical deposition into SiO2/Si ion-track template formed by 200 MeV Xe ion irradiation with the fluence of 107 ions/cm2. The lattice parameters determined by the X-ray diffraction and calculated by the CRYSTAL computer program package are very close to each other. It was found that ZnSeO3 has a direct band gap of 3.8 eV at the Γ-point. The photoluminescence excited by photons at 300 nm has a low intensity, arising mainly due to zinc and oxygen vacancies. Photoluminescence excited by photons with a wavelength of 300 nm has a very low intensity, presumably due to electronic transitions of zinc and oxygen vacancies.

Study of Structural, Strength, and Thermophysical Properties of Li2+4xZr4−xO3 Ceramics

The work is devoted to the study of technology that can be used to obtain lithium-containing ceramics of the Li2+4xZr4−xO3 type using the method of solid-phase synthesis combined with thermal annealing at a temperature of 1500 °C. A distinctive feature of this work is the preparation of pure Li2ZrO3 ceramics with a high structural ordering degree (more than 88%) and density (95–97% of the theoretical density). During the study, it was found that a change in the content of initial components for synthesis does not lead to the formation of new phase inclusions; however, an increase in the LiClO4·3H2O and ZrO2 components leads to changes in the size of crystallites and dislocation density, which lead to the strengthening of ceramics to external mechanical influences. The results of the measurements of thermophysical characteristics made it possible to establish that the compaction of ceramics and a decrease in porosity lead to an increase in the thermal conductivity coefficient of 3–7%.

Improving the Structural, Optical and Photovoltaic Properties of Sb- and Bi- Co-Doped MAPbBr3 Perovskite Solar Cell

We prepared 1% Bi- and (0, 0.5%, 1% and 1.5%) Sb- co-doped MAPbBr3 films by a sol-gel spin coating technique. For the first time, the detailed structural properties including grain size, dislocation line density, d-spacing, lattice parameters, and volume of co-doped MAPbBr3 films have been investigated. XRD confirmed the cubic structure of MAPbBr3 with high crystallinity and co-doping of Bi and Sb. The 1% Bi and 1% Sb co-doping have a surprising effect in MAPbBr3 structures, such as large grain size (59.5 nm), d-space value (6.23 Å), small dislocation line dislocation (2.79 × 1018 m−2), and small lattice parameters (a = b = c = 6.3 Å) and volume of unit cell. The detailed optical properties, including energy band gap (Eg), refractive index (n), extinction coefficient (k) and dielectric constant (Ɛ), which are very important for optoelectronics applications, were investigated by UV-Vis spectroscopy. The film of 1% Bi and 1% Sb co-doped MAPbBr3 showed good optical response including small Eg, high n, low value of k, high real and low imaginary parts of dielectric constant, making it good for solar cell applications. Solar cells were fabricated from these films. The cell fabricated with pure MAPbBr3 has Jsc of 8.72 mA cm−2, FF of 0.66, Voc of 1.29 V, and η of 7.5%. All the parameters increased by co-doping of Bi and Sb in MAPbBr3 film. The cell fabricated with 1% Bi and 1% Sb co-doped MAPbBr3 film had high current density (12.12 mA-cm−2), open circuit voltage (Voc), fill factor (0.73), and high efficiency (11.6%). This efficiency was 65% larger than a pure MAPbBr3-based solar cell.

Non-Stacked γ-Fe2O3/C@TiO2 Double-Layer Hollow Nanoparticles for Enhanced Photocatalytic Applications under Visible Light

Herein, a non-stacked γ-Fe₂O₃/C@TiO₂ double-layer hollow nano photocatalyst has been developed with ultrathin nanosheets-assembled double shells for photodegradation phenol. High catalytic performance was found that the phenol could be completely degraded in 135 min under visible light, due to the moderate band edge position (VB at 0.59 eV and CB at −0.66 eV) of the non-stacked γ-Fe₂O₃/C@TiO₂, which can expand the excitation wavelength range into the visible light region and produce a high concentration of free radicals (such as ·OH, ·O²⁻, holes). Furthermore, the interior of the hollow composite γ-Fe₂O₃ is responsible for charge generation, and the carbon matrix facilitates charge transfer to the external TiO₂ shell. This overlap improved the selection/utilization efficiency, while the unique non-stacked double-layered structure inhibited initial charge recombination over the photocatalysts. This work provides new approaches for photocatalytic applications with γ-Fe₂O₃/C-based materials.

Enhancing DFT-based energy landscape exploration by coupling Quantum Mechanics and Static Modes

Unravelling the atomic scale diffusion that can occur at the surface, at the interface or into the bulk is challenging: multi-scale modelling approach usually requires intensive prospective calculations and moreover...

Positron Annihilation Lifetime Spectroscopy Insight on Free Volume Conversion of Nanostructured MgAl2O4 Ceramics

Herein we demonstrate the specifics of using the positron annihilation lifetime spectroscopy (PALS) method for the study of free volume changes in functional ceramic materials. Choosing technological modification of nanostructured MgAl₂O₄ spinel as an example, we show that for ceramics with well-developed porosity positron annihilation is revealed through two channels: positron trapping channel and ortho-positronium decay. Positron trapping in free-volume defects is described by the second component of spectra and ortho-positronium decay process by single or multiple components, depending on how well porosity is developed and on the experimental configuration. When using proposed positron annihilation lifetime spectroscopy approaches, three components are the most suitable fit in the case of MgAl₂O₄ ceramics. In the analysis of the second component, it is shown that technological modification (increasing sintering temperature) leads to volume shrinking and decreases the number of defect-related voids. This process is also accompanied by the decrease of the size of nanopores (described by the third component), while the overall number of nanopores is not affected. The approach to the analysis of positron annihilation lifetime spectra presented here can be applied to a wide range of functional nanomaterials with pronounced porosity.

Structural, Optical, and Catalytic Properties of MgCr2O4 Spinel-Type Nanostructures Synthesized by Sol–Gel Auto-Combustion Method

Spinel chromite nanoparticles are prospective candidates for a variety of applications from catalysis to depollution. In this work, we used a sol–gel auto-combustion method to synthesize spinel-type MgCr2O4 nanoparticles by using fructose (FS), tartaric acid (TA), and hexamethylenetetramine (HMTA) as chelating/fuel agents. The optimal temperature treatment for the formation of impurity-free MgCr2O4 nanostructures was found to range from 500 to 750 °C. Fourier transform infrared (FTIR) spectroscopy was used to determine the lattice vibrations of the corresponding chemical bonds from octahedral and tetrahedral positions, and the optical band gap was calculated from UV–VIS spectrophotometry. The stabilization of the spinel phase was proved by X-ray diffraction (XRD) and energy-dispersive X-ray (EDX) analysis. From field-emission scanning electron microscopy (FE-SEM), we found that the size of the constituent particles ranged from 10 to 40 nm. The catalytic activity of the as-prepared MgCr2O4 nanocrystals synthesized by using tartaric acid as a chelating/fuel agent was tested on the decomposition of hydrogen peroxide. In particular, we found that the nature of the chelating/fuel agent as well as the energy released during the auto-combustion played an important role on the structural, optical, and catalytic properties of MgCr2O4 nanoparticles obtained by this synthetic route.

A Study on the Applicability of NiFe2O4 Nanoparticles as the Basis of Catalysts for the Purification of Aqueous Media from Pollutants

The aim of this work is to evaluate the application of NiFe2O4 nanoparticles with spinel structures as the basis of catalysts for the purification of aqueous media from pollutants such as manganese and arsenic. The interest in these catalysts is due to their ease of production and high absorption efficiency, which, together with their magnetic properties, allow the use of nanoparticles for a long time. The sol–gel method, followed by thermal annealing of the samples at different temperatures, was proposed as a method for the synthesis of spinel nanoparticles. The choice of the annealing temperature range of 200–1000 °C is caused by the possibility of estimating changes in the structural properties and the degree of nanoparticles crystallinity. During the study of structural changes in nanoparticles depending on the annealing temperature, it was found that in the temperature range of 200–800 °C, there is an ordering of structural parameters, while for samples obtained at annealing temperatures above 800 °C, there is a partial disorder caused by the agglomeration of nanoparticles with a subsequent increase in their size. According to the results of the studies on the purification of aqueous media from pollutants, it was found that the greatest absorption efficiency belongs to nanoparticles annealed at 500–700 °C, with the purification efficiency of 70–85%, depending on the type of pollutant. The results obtained from the use of nanoparticles as catalysts for the purification of aqueous media show great prospects for their further application on an industrial scale.

Evidence for the formation of two types of oxygen interstitials in neutron-irradiated α-Al2O3 single crystals

Due to unique optical/mechanical properties and significant resistance to harsh radiation environments, corundum (α-Al₂O₃) is considered as a promising candidate material for windows and diagnostics in forthcoming fusion reactors. However, its properties are affected by radiation-induced (predominantly, by fast neutrons) structural defects. In this paper, we analyze thermal stability and recombination kinetics of primary Frenkel defects in anion sublattice − the F-type electronic centers and complementary oxygen interstitials in fast-neutron-irradiated corundum single crystals. Combining precisely measured thermal annealing kinetics for four types of primary radiation defects (neutral and charged Frenkel pairs) and the advanced model of chemical reactions, we have demonstrated for the first time a co-existence of the two types of interstitial defects – neutral O atoms and negatively charged O^- ions (with attributed optical absorption bands peaked at energies of 6.5 eV and 5.6 eV, respectively). From detailed analysis of interrelated kinetics of four oxygen-related defects, we extracted their diffusion parameters (interstitials serve as mobile recombination partners) required for the future prediction of secondary defect-induced reactions and, eventually, material radiation tolerance.

Atomic, electronic and magnetic structure of an oxygen interstitial in neutron-irradiated Al2O3 single crystals

A single radiation-induced superoxide ion \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$O_{2}^{ - }$$\end{document}O2- has been observed for the first time in metal oxides. This structural defect has been revealed in fast-neutron-irradiated (6.9×10¹⁸n/cm²) corundum (α-Al₂O₃) single crystals using the EPR method. Based on the angular dependence of the EPR lines at the magnetic field rotation in different planes and the determined g tensor components, it is shown that this hole-type \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$O_{2}^{ - }$$\end{document}O2- center (i) incorporates one regular and one interstitial oxygen atoms being stabilized by a trapped hole (S = 1/2), (ii) occupies one oxygen site in the (0001) plane being oriented along the a axis, and (iii) does not contain any other imperfection/defect in its immediate vicinity. The thermal stepwise annealing (observed via the EPR signal and corresponding optical absorption bands) of the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$O_{2}^{ - }$$\end{document}O2- centers, caused by their destruction with release of a mobile ion (tentatively the oxygen ion with the formal charge −1), occurs at 500–750 K, simultaneously with the partial decay of single F-type centers (mostly with the EPR-active F⁺ centers). The obtained experimental results are in line with the superoxide defect configurations obtained via density functional theory (DFT) calculations employing the hybrid B3PW exchange-correlation functional. In particular, the DFT calculations confirm the \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$O_{2}^{ - }$$\end{document}O2- center spin S = 1/2, its orientation along the a axis. The \documentclass[12pt]{minimal} \usepackage{amsmath} \usepackage{wasysym} \usepackage{amsfonts} \usepackage{amssymb} \usepackage{amsbsy} \usepackage{mathrsfs} \usepackage{upgreek} \setlength{\oddsidemargin}{-69pt} \begin{document}$$O_{2}^{ - }$$\end{document}O2- center is characterized by a short O–O bond length of 1.34 Å and different atomic charges and magnetic moments of the two oxygens. We emphasize the important role of atomic charges and magnetic moments analysis in order to identify the ground state configuration.