1
|
Dey D, Liang L, Yu L. Mixed Enthalpy-Entropy Descriptor for the Rational Design of Synthesizable High-Entropy Materials Over Vast Chemical Spaces. J Am Chem Soc 2024; 146:5142-5151. [PMID: 38353456 DOI: 10.1021/jacs.4c00209] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Indexed: 02/29/2024]
Abstract
The practically unlimited high-dimensional composition space of high-entropy materials (HEMs) has emerged as an exciting platform for functional material design and discovery. However, the identification of stable and synthesizable HEMs and robust design rules remains a daunting challenge. Here, we propose a mixed enthalpy-entropy descriptor (MEED) that enables highly efficient, robust, high-throughput prediction of synthesizable HEMs across vast chemical spaces from first-principles. The MEED is based on two parameters: the relative formation enthalpy with respect to the most stable competing compound and the spread of the point-defect formation energy spectrum. The former measures the relative synthesizability of an HEM to its most stable competing phase, going beyond the conventional thermodynamic understanding. The latter gauges the relative entropy forming ability of an HEM, entailing no sampling over numerous alloy configurations. By applying the MEED to two structurally distinct representative material systems (i.e., 3D rocksalt carbides and 2D layered sulfides), we not only successfully identify all experimentally reported HEMs within these systems but also reveal a cutoff criterion for assessing their relative synthesizability within each system. By the MEED, tens of new high-entropy carbides and 2D high-entropy sulfides are also predicted, which have the potential for a wide variety of applications such as coating in aerospace devices, energy conversion and storage, and flexible electronics.
Collapse
Affiliation(s)
- Dibyendu Dey
- Department of Physics and Astronomy, University of Maine, Orono, Maine 04469, USA
| | - Liangbo Liang
- Center for Nanophase Materials Sciences, Oak Ridge National Laboratory, Oak Ridge, Tennessee 37831, USA
| | - Liping Yu
- Department of Physics and Astronomy, University of Maine, Orono, Maine 04469, USA
- Department of Materials Science and Engineering, University of Central Florida, Orlando, Florida 32816, USA
| |
Collapse
|
2
|
Sorkin V, Yu ZG, Chen S, Tan TL, Aitken Z, Zhang YW. First principles-based design of lightweight high entropy alloys. Sci Rep 2023; 13:22549. [PMID: 38110508 PMCID: PMC10728166 DOI: 10.1038/s41598-023-49258-z] [Citation(s) in RCA: 0] [Impact Index Per Article: 0] [Reference Citation Analysis] [Abstract] [Key Words] [Grants] [Track Full Text] [Journal Information] [Subscribe] [Scholar Register] [Received: 05/24/2023] [Accepted: 12/06/2023] [Indexed: 12/20/2023] Open
Abstract
Recently, the design of lightweight high entropy alloys (HEAs) with a mass density lower than 5 g/cm3 has attracted much research interest in structural materials. We applied a first principles-based high-throughput method to design lightweight HEAs in single solid-solution phase. Three lightweight quinary HEA families were studied: AlBeMgTiLi, AlBeMgTiSi and AlBeMgTiCu. By comprehensively exploring their entire compositional spaces, we identified the most promising compositions according to the following design criteria: the highest stability, lowest mass density, largest elastic modulus and specific stiffness, along with highest Pugh's ratio. We found that HEAs with the topmost compositions exhibit a negative formation energy, a low density and high specific Young's modulus, but a low Pugh's ratio. Importantly, we show that the most stable composition, Al0.31Be0.15Mg0.14Ti0.05Si0.35 is energetically more stable than its metallic compounds and it significantly outperforms the current lightweight engineering alloys such as the 7075 Al alloy. These results suggest that the designed lightweight HEAs can be energetically more stable, lighter, and stiffer but slightly less ductile compared to existing Al alloys. Similar conclusions can be also drawn for the AlBeMgTiLi and AlBeMgTiCu. Our design methodology and findings serve as a valuable tool and guidance for the experimental development of lightweight HEAs.
Collapse
Affiliation(s)
- Viacheslav Sorkin
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore.
| | - Zhi Gen Yu
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore
| | - Shuai Chen
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore
- Materials Genome Institute, Shanghai University, Shanghai, 200444, China
| | - Teck Leong Tan
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore
| | - Zachary Aitken
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore
| | - Yong-Wei Zhang
- Institute of High Performance Computing (IHPC), Agency for Science, Technology and Research (A*STAR), 1 Fusionopolis Way, #16-16 Connexis, Singapore, 138632, Republic of Singapore.
| |
Collapse
|