Effect of hydration on the anatomical form of human dry skulls

Ballistic Gels in Experimental Fracture Setting

Biomechanical tests typically involve bending, compression, or shear stress, while fall tests are less common. The main challenge in performing fall tests is the non-reproducible directionality of bone when tested with soft tissue. Upon removal of the soft tissue, the explanted bone's resistance to impact diminishes. Therefore, ballistic gels can fix specimens in reproducible directions and simulate periosteal soft tissue. However, the use of ballistic gels in biomechanical studies is neither standardized nor widespread. This study aimed to optimize a ballistic gel consistency that mimics the upper thigh muscle in sheep. Our results suggest a standardized and flexible evaluation method by embedding samples in ballistic gel. Compression tests were conducted using cylindrical pieces of gluteal muscle from sheep. Various compositions of agarose and gelatin mixtures were tested to achieve a muscle-like consistency. The muscle-equivalent ballistic gel was found to consist of 29.5% gelatin and 0.35% agarose. Bones remained stable within the ballistic gel setup after freeze-thaw cycles between -20 °C and +20 °C. This method reduces the variability caused by muscle and improves storage quality, allowing for tests to be conducted under consistent conditionsBallistic gels of agarose and gelatin are suitable for bone fracture models. They have muscle-like strength, fix fractures simultaneously, are inexpensive to produce, and can be stored to allow repeated measurements of the same object with changing questions.

Feasibility of frozen soft tissues to simulate fresh soft tissue conditions in cone beam CT scans

OBJECTIVES

To evaluate the feasibility of frozen soft tissues in simulating fresh soft tissues of pig mandibles using cone beam CT (CBCT).

METHODS

Two fresh pig mandibles with soft tissues containing 2 tubes filled with a radiopaque homogeneous solution were scanned using 4 CBCT units and 2 field-of-view (FOV) sizes each. The pig mandibles were deep-frozen and scanned again. Three cross-sections were exported from each CBCT volume and grouped into pairs, with one cross-section representing a fresh and one a frozen mandible. Three radiologists compared the pairs and attributed a score to assess the relative image quality using a 5-point scale. Mean grey values and standard deviation were obtained from homogeneous areas in the tubes, compared using the Wilcoxon matched-pair signed-rank test and subjected to Pearson correlation analysis between fresh and frozen physical states (α = .05).

RESULTS

Subjective evaluation revealed similarity of the CBCT image quality between fresh and frozen states. The distribution of mean grey values was similar between fresh and frozen states. Mean grey values of the frozen state in the small FOV were significantly greater than those of the fresh state (P = .037), and noise values of the frozen state in the large FOV were significantly greater than those of the fresh state (P = 0.007). Both mean grey values and noise exhibited significant and positive correlations between fresh and frozen states (P < 0.01).

CONCLUSIONS

The freezing of pig mandibles with soft tissues may serve as a method to prolong their usability and working time when CBCT imaging is planned.

Accuracy of facial skeletal surfaces segmented from CT and CBCT radiographs

The accuracy of three-dimensional (3D) facial skeletal surface models derived from radiographic volumes has not been extensively investigated yet. For this, ten human dry skulls were scanned with two Cone Beam Computed Tomography (CBCT) units, a CT unit, and a highly accurate optical surface scanner that provided the true reference models. Water-filled head shells were used for soft tissue simulation during radiographic imaging. The 3D surface models that were repeatedly segmented from the radiographic volumes through a single-threshold approach were used for reproducibility testing. Additionally, they were compared to the true reference model for trueness measurement. Comparisons were performed through 3D surface approximation techniques, using an iterative closest point algorithm. Differences between surface models were assessed through the calculation of mean absolute distances (MAD) between corresponding surfaces and through visual inspection of facial surface colour-coded distance maps. There was very high reproducibility (approximately 0.07 mm) and trueness (0.12 mm on average, with deviations extending locally to 0.5 mm), and no difference between radiographic scanners or settings. The present findings establish the validity of lower radiation CBCT imaging protocols at a similar level to the conventional CT images, when 3D surface models are required for the assessment of facial morphology.