Synthesis, Structural and Optical Properties of ZrBi2Se6 Nanoflowers: A Next-Generation Semiconductor Alloy Material for Optoelectronic Applications

ZrBi2Se6 nanoflower-like morphology was successfully prepared using a solvothermal method, followed by a quenching process for photoelectrochemical water splitting applications. The formation of ZrBi2Se6 was confirmed by field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD), Raman spectroscopy, and X-ray photoelectron spectroscopy (XPS). The estimated value of work function and band gap were found to be 5.5 and 2.26 eV measured using diffuse reflection spectroscopy and ultraviolet photoelectron spectroscopy, suggesting the potential candidate for water splitting. The highest current density of 9.7 μA/cm2 has been observed for the ZrBi2Se6 photoanode for the applied potential of 0.5 V vs SCE. The flat-band potential value was -0.46 V, and the 1.85 nm width of the depletion region is estimated from the Mott-Schottky (MS) analysis. It also reveals that the charge carrier density for the ZrBi2Se6 nanoflowers is 4.8 × 1015 cm-3. The negative slope of the MS plot indicates that ZrBi2Se6 is a p-type semiconductor. It was observed that ZrBi2Se6 nanoflowers had a high charge transfer resistance of ∼730 kΩ and equivalent capacitance of ∼40 nF calculated using electrochemical impedance spectroscopy (EIS) measurements. Using chronoamperometry, the estimated rise time and decay time were 50 ms and 0.25 s, respectively, which reveals the fast photocurrent response and excellent PEC performance of the ZrBi2Se6 photoanode. Furthermore, an attempt has been made to explain the PEC activity of ZrBi2Se6 nanoflowers using an energy band diagram. Thus, the initial results on ZrBi2Se6 nanoflowers appear promising for the PEC activity toward water splitting.

Saussurea lappa plant rhizome extract-based zinc oxide nanoparticles: synthesis, characterization and its antibacterial, antifungal activities and cytotoxic studies against Chinese Hamster Ovary (CHO) cell lines

The plant extracts are known for their anti-inflammatory, antifungal, antiviral and antibacterial properties. The use of plant extracts in the preparation of bio-materials increases their biological application. In this concern, herein reporting an eco-friendly procedure which is also a simple and cost effective, for the synthesis of Zinc Oxide nanoparticles (ZnONPs) using Saussurea lappa plant root (rhizome) extract as a fuel. The prepared nanoparticles were confirmed using various characterization techniques. The Dynamic light scattering data showed 123.5 nm particle size with -99.9 mv zeta potential which indicates excellent stability of the particles. The peak at 541 cm-1 in the IR spectrum is assigned to the stretching frequency of the zinc-binding to oxygen. The X-ray diffraction peaks confirm the close association with JCPDS Data Card No: 36-1451. The FESEM data revealed a hexagonal wurtzite structure with a hexagonal shape of synthesized ZnO nanoparticles. The antibacterial studies indicate the gram-negative strains showed better inhibition activity than gram-positive strains. Among Fungal strains, Aspergillus niger and flavus, Fusarium oxysporum, and Rhizopus oryzae showed good inhibition activity at higher concentrations. The cytotoxic data indicates the 5 μg/mL of the ZnO particles showed cytotoxicity on the CHO cell line and with IC50 value 3.164 ± 0.8956 μg/mL.

A highly efficient porous rod-like Ce-doped ZnO photocatalyst for the degradation of dye contaminants in water

A mild and simple method was developed to synthesize a highly efficient photocatalyst comprised of Ce-doped ZnO rods and optimal synthesis conditions were determined by testing samples with different Ce/ZnO molar ratios calcined at 500 °C for 3 hours via a one-step pyrolysis method. The photocatalytic activity was assessed by the degradation of a common dye pollutant found in wastewater, rhodamine B (RhB), using a sunlight simulator. The results showed that ZnO doped with 3% Ce exhibits the highest RhB degradation rate. To understand the crystal structure, elemental state, surface morphology and chemical composition, the photocatalysts were characterized by X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), scanning electron microscope (SEM) and inductively coupled plasma emission spectroscopy (ICP), respectively. The newly developed, robust, field-only surface integral method was employed to explore the relationship between the remarkable catalytic effect and the catalyst shape and porous microstructure. The computational results showed that the dipole-like field covers the entire surface of the rod-like Ce-doped ZnO photocatalyst and is present over the entire range of wavelengths considered. The optimum degradation conditions were determined by orthogonal tests and range analysis, including the concentration of RhB and catalyst, pH value and temperature. The results indicate that the pH value is the main influential factor in the photocatalytic degradation process and the optimal experimental conditions to achieve the maximum degradation rate of 97.66% in 2 hours are as follows: concentration (RhB) = 10 mg/L, concentration (catalyst) = 0.7 g/L, pH 9.0 and T = 50 °C. These optimum conditions supply a helpful reference for large-scale wastewater degradation containing the common water contaminant RhB.

Three-Dimensional ZnO Hierarchical Nanostructures: Solution Phase Synthesis and Applications

Zinc oxide (ZnO) nanostructures have been studied extensively in the past 20 years due to their novel electronic, photonic, mechanical and electrochemical properties. Recently, more attention has been paid to assemble nanoscale building blocks into three-dimensional (3D) complex hierarchical structures, which not only inherit the excellent properties of the single building blocks but also provide potential applications in the bottom-up fabrication of functional devices. This review article focuses on 3D ZnO hierarchical nanostructures, and summarizes major advances in the solution phase synthesis, applications in environment, and electrical/electrochemical devices. We present the principles and growth mechanisms of ZnO nanostructures via different solution methods, with an emphasis on rational control of the morphology and assembly. We then discuss the applications of 3D ZnO hierarchical nanostructures in photocatalysis, field emission, electrochemical sensor, and lithium ion batteries. Throughout the discussion, the relationship between the device performance and the microstructures of 3D ZnO hierarchical nanostructures will be highlighted. This review concludes with a personal perspective on the current challenges and future research.

TiO2 cement for high-performance dye-sensitized solar cells

An energy conversion efficiency of 8.31% is reached by using a cemented photoanode for dye-sensitized solar cells, attaining a 31.1% improvement over the standard Degussa P25 sample.

Controllable synthesis of InTaO4 catalysts of different morphologies using a versatile sol precursor for photocatalytic evolution of H2

For the first time, InTaO₄ photocatalysts with different morphologies and structures were facilely prepared using a versatile sol precursor.

Anatase TiO2 with nanopores for dye-sensitized solar cells

By using different carboxylic acids as solvents, the morphology of the integral TiO₂ crystals as well as inner pores can be tuned. Further application as the photoanode of DSCs resulted in an overall energy conversion efficiency of 7.55% due to their low electrical resistivity and improved light harvesting abilities.