Enhanced photoelectrochemical water splitting using carbon cloth functionalized with ZnO nanostructures via polydopamine assisted electroless deposition

ZnO nanorods (ZnO-nr) have been widely studied as a promising nanomaterial for photoelectrochemical water splitting. However, almost all prior studies employed planar electrodes. Here, we investigated the performance of ZnO nanorods on a fibrous carbon cloth (CC) electrode, which offers a larger surface area for functionalization of photocatalysts. ZnO nanorods and Ni nanofilm were deposited on carbon cloth substrates for investigation as the photoanode and cathode of a photoelectrochemical water splitting setup, respectively. The use of polydopamine in the electroless deposition of ZnO ensured a uniform distribution of nanorods that were strongly adherent to the microfiber surface of the carbon cloth. Compared to ZnO nanorods grown on planar ITO/glass substrates, the CC-based ZnO photoanodes exhibited smaller onset potentials (1.1 VRHEvs. 1.8 VRHE), ∼40× larger dark faradaic currents at 1.23 VRHE and 5.5×-9× improvement in photoconversion efficiencies. Ni/CC cathodes were also found to exhibit a lower overpotential@10 mA cm-2 than Ni/Cu by 90 mV. The photocurrent obtained from the ZnO-nr/CC anode was highly stable across an hour and the peak current decreased by only 5% across 5 cycles of illumination, compared to 72% for the planar ZnO-nr/ITO anode. However, the response of the CC-based setups to changes in the illumination conditions was slower, taking hundreds of seconds to reach peak photocurrent, compared to tens of seconds for the planar electrodes. Using cyclic voltammetry, the double-layer capacitance of the electrodes was measured, and it was shown that the increased efficiency of the ZnO-nr/CC anode was due to a 2 order of magnitude increase in electrochemically active sites provided by the copious microfiber surface of the carbon cloth.

Structural and antibacterial studies of novel ZnO and ZnxMn(1-x)O nanostructured titanium scaffolds for biomedical applications

In the biomedical field, the demand for the development of broad-spectrum biomaterials able to inhibit bacterial growth is constantly increasing. Chronic infections represent the most serious and devastating complication related to the use of biomaterials. This is particularly relevant in the orthopaedic field, where infections can lead to implant loosening, arthrodesis, amputations and sometimes death. Antibiotics are the conventional approach for implanted-associated infections, but they have the limitation of increasing antibiotic resistance, a critical worldwide healthcare issue. In this context, the development of anti-infective biomaterials and infection-resistant surfaces can be considered the more effective strategy to prevent the implant colonisation and biofilm formation by bacteria, so reducing the occurrence of implant-associated infections. In the last years, inorganic nanostructures have become extremely appealing for chemical modifications or coatings of Ti surfaces, since they do not generate antibiotic resistance issues and are featured by superior stability, durability, and full compatibility with the sterilization process. In this work, we present a simple, rapid, and cheap chemical nanofunctionalization of titanium (Ti) scaffolds with colloidal ZnO and Mn-doped ZnO nanoparticles (NPs), prepared by a sol-gel method, exhibiting antibacterial activity. ZnO NPs and Zn_xMn_(1-x)O NPs formation with a size around 10-20nm and band gap values of 3.42 eV and 3.38 eV, respectively, have been displayed by characterization studies. UV-Vis, fluorescence, and Raman investigation suggested that Mn ions acting as dopants in the ZnO lattice. Ti scaffolds have been functionalized through dip coating, obtaining ZnO@Ti and Zn_xMn_(1-x)O@Ti biomaterials characterized by a continuous nanostructured film. ZnO@Ti and Zn_xMn_(1-x)O@Ti displayed an enhanced antibacterial activity against both Gram-positive Staphylococcus aureus (S. aureus) and Gram-negative Pseudomonas aeruginosa (P. aeruginosa) bacterial strains, compared to NPs in solution with better performance of Zn_xMn_(1-x)O@Ti respect to ZnO@Ti. Notably, it has been observed that Zn_xMn_(1-x)O@Ti scaffolds reach a complete eradication for S. aureus and 90 % of reduction for P. aeruginosa. This can be attributed to Zn²⁺ and Mn²⁺ metal ions release (as observed by ICP MS experiments) that is also maintained over time (72 h). To the best of our knowledge, this is the first study reported in the literature describing ZnO and Mn-doped ZnO NPs nanofunctionalized Ti scaffolds with improved antibacterial performance, paving the way for the realization of new hybrid implantable devices through a low-cost process, compatible with the biotechnological industrial chain method.

Evaluation of the antibacterial properties and in-vitro cell compatibilities of doped copper oxide/hydroxyapatite composites

Mg, Zn and Ce-doped CuO/HA composites were prepared by a two-step sol-gel and hydrothermal process. SEM images showed a spherical appearance of HA and a needle-like morphology for doped CuO. XRD patterns revealed that all doped CuO/HA composites exhibited a hexagonal crystal structure of HA and a monoclinic crystal structure of CuO with no impurities. ICP analysis indicated that with the increase of loading amount of doped CuO, the concentrations of Cu²⁺ ions and doping ions released from composites increased. Moreover, CuO/HA composites exhibit improved antibacterial properties against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) as compared with HA. When the loading amount of doped CuO in composites increased to 15 wt%, the composites exhibited the best antibacterial activity and complete bacterial growth inhibition effect. Furthermore, the CCK-8 assay revealed that the doped CuO/HA composites are noncytotoxic and can promote the proliferation of osteosarcoma cells. This work highlights the potential of the doped CuO/HA composites with significant antibacterial activity, bioactivity and cell compatibility for potential biomedical applications in dental implants and bone regeneration.

The role of magnesium in biomaterials related infections

Magnesium is currently increasing interest in the field of biomaterials. An extensive bibliography on this material in the last two decades arises from its potential for the development of biodegradable implants. In addition, many researches, motivated by this progress, have analyzed the performance of magnesium in both in vitro and in vivo assays with gram-positive and gram-negative bacteria in a very broad range of conditions. This review explores the extensive literature in recent years on magnesium in biomaterials-related infections, and discusses the mechanisms of the Mg action on bacteria, as well as the competition of Mg²⁺ and/or synergy with other divalent cations in this subject.

Synthesis and evaluation of the structural and antibacterial properties of doped copper oxide

Mg, Zn, and Ce-doped CuO NPs exhibit significantly enhanced antibacterial activity due to the synergetic effect of Cu²⁺ and ROS generation.

Superhydrophobicity: advanced biological and biomedical applications

The biological and biomedical applications of superhydrophobic surface.

Electroless controllable growth of ZnO films and their morphology-dependent antimicrobial properties

An electroless deposition process was used to synthesize with a controlled morphology, polycrystalline ZnO on glass substrates as antimicrobial coatings. The influence of deposition temperature (T_dep) on the physicochemical and antimicrobial properties of the ZnO films was analyzed. The results indicated that a change in deposition temperature greatly affected the morphology and the degree of crystallinity of the films. Scanning electron microscope images show that the film surface is porous at a deposition temperature of 40 and 50 °C, whereas hexagonal-plate shaped morphology predominated at 60 °C and finally at 70 and 80 °C the films consisted of rod-like particles. The films showed good transparency in the visible region. All ZnO films presented notable antimicrobial activity against the gram-negative bacteria Escherichia coli (E. coli) and the gram-positive Staphylococcus aureus (S. aureus). It was found that the antimicrobial efficiency is strongly dependent on morphology and structural properties. The best antimicrobial performance was recorded for the films consisting of rod-like morphology with a high degree of crystallinity. The procedure used in this investigation is strongly recommended for the development of functional surfaces.

Sustainable Life Cycles of Natural-Precursor-Derived Nanocarbons

Sustainable societal and economic development relies on novel nanotechnologies that offer maximum efficiency at minimal environmental cost. Yet, it is very challenging to apply green chemistry approaches across the entire life cycle of nanotech products, from design and nanomaterial synthesis to utilization and disposal. Recently, novel, efficient methods based on nonequilibrium reactive plasma chemistries that minimize the process steps and dramatically reduce the use of expensive and hazardous reagents have been applied to low-cost natural and waste sources to produce value-added nanomaterials with a wide range of applications. This review discusses the distinctive effects of nonequilibrium reactive chemistries and how these effects can aid and advance the integration of sustainable chemistry into each stage of nanotech product life. Examples of the use of enabling plasma-based technologies in sustainable production and degradation of nanotech products are discussed-from selection of precursors derived from natural resources and their conversion into functional building units, to methods for green synthesis of useful naturally degradable carbon-based nanomaterials, to device operation and eventual disintegration into naturally degradable yet potentially reusable byproducts.

Addition of Zn to the ternary Mg-Ca-Sr alloys significantly improves their antibacterial property

Most of the magnesium (Mg) alloys possess excellent biocompatibility, mechanical property and biodegradability in orthopedic applications. However, these alloys may suffer from bacterial infections due to their insufficient antibacterial capability. In order to reduce the post-surgical infections, a series of biocompatible Mg-1Ca-0.5Sr-xZn (x=0, 2, 4, 6) alloys were fabricated with the addition of antibacterial Zn with variable content and evaluated in terms of their biocompatibility and antibacterial property. The in vitro corrosion study showed that Mg-1Ca-0.5Sr-6Zn alloys exhibited a higher hydrogen evolution volume after 100 h immersion and resulted in a higher pH value of the immersion solution. Our work indicated that Zn-containing Mg alloys exhibited good biocompatibility with high cell viability. The antibacterial studies reveal that the number of bacteria adhered on all of these Mg alloy samples diminished remarkably compared to the Ti-6Al-4V control group. We also found that the proliferation of the bacteria was inhibited by these Mg alloys extracts. Among the prepared alloys, Mg-1Ca-0.5Sr-6Zn alloy not only exhibited a strong antibacterial effect, but also promoted the proliferation of MC3T3-E1 osteoblasts, suggesting that it is a promising alloy with both good antibacterial property and good biocompatibility for use as an orthopedic implant.

Anti-bacterial surfaces: natural agents, mechanisms of action, and plasma surface modification

This article reviews antibacterial surface strategies based on reactive plasma chemistry, focusing on how plasma-assisted processing of natural antimicrobial agents can produce antifouling and antibacterial materials for biomedical devices.

Superhydrophobic surface with hierarchical architecture and bimetallic composition for enhanced antibacterial activity

Developing robust antibacterial materials is of importance for a wide range of applications such as in biomedical engineering, environment, and water treatment. Herein we report the development of a novel superhydrophobic surface featured with hierarchical architecture and bimetallic composition that exhibits enhanced antibacterial activity. The surface is created using a facile galvanic replacement reaction followed by a simple thermal oxidation process. Interestingly, we show that the surface's superhydrophobic property naturally allows for a minimal bacterial adhesion in the dry environment, and also can be deactivated in the wet solution to enable the release of biocidal agents. In particular, we demonstrate that the higher solubility nature of the thermal oxides created in the thermal oxidation process, together with the synergistic cooperation of bimetallic composition and hierarchical architecture, allows for the release of metal ions in a sustained and accelerated manner, leading to enhanced antibacterial performance in the wet condition as well. We envision that the ease of fabrication, the versatile functionalities, and the robustness of our surface will make it appealing for broad applications.

TiO2/ZnO nanocomposite, ZnO/ZnO bi-level nanostructure and ZnO nanorod arrays: microstructure and time-affected wettability change in ambient conditions

Wettability is an important property of surfaces and interfaces. Understanding the wetting behavior of semiconductors and its relationship with their microstructures has aroused much interest because of the great advantages this gives to various functional applications.

Micro-/nanometer rough structure of a superhydrophobic biodegradable coating by electrospraying for initial anti-bioadhesion

A novel superhydrophobic biodegradable coating with micro-/nanometer rough structure, fabricated by co-electrospraying poly(L-lactide) (PLLA) and modified silica nanoparticles (MSNs), exhibits good anti-adhesion behavior towards bacteria and cells in the initial culturing phase, which makes it a promising technology for preparing medical device coatings.

Simple, large-scale patterning of hydrophobic ZnO nanorod arrays

Here we describe a simple, versatile technique to produce large-scale arrays of highly ordered ZnO nanorods. Patterning of three distinct ZnO crystal morphologies is demonstrated through use of different ZnO seed layers. Array formation is accomplished through a simple variation on nanosphere lithography that imprints a thickness variation across a PMMA mask layer. The area of exposed seed layer is controlled through etching time in an oxygen plasma. Subsequent hydrothermal growth from the patterned seed layer produces high-quality ZnO crystals in uniform arrays. The high uniformity of the patterned array is shown to induce a high contact angle hydrophobic state even without the need for chemical modification of the ZnO surface. This technique provides a straightforward way to integrate the optical and electrical properties of high-quality ZnO nanorods with the tunable fluidic properties at the surface of well-ordered arrays.