Efficient hybrid plasmonic polymer solar cells with Ag nanoparticle decorated TiO2 nanorods embedded in the active layer

Metasurface absorber based single junction thin film solar cell exceeding 30% efficiency

In this article, we report, as per our knowledge, for the first time, a thin film single junction solar cell with a metasurface absorber layer directly incorporated. We have used an interconnected dual inverted split ring resonator pattern in the InAsP absorber layer. The structure eliminated patterns of conventional metals, such as silver, aluminum, and gold, from the active layer, a common drawback in conventional solar absorbers, hindering their direct integration into solar cells. Optical simulation results show a peak ideal short circuit current density of 76.23mA/cm2 for the meta-absorber structure under solar illumination. This current is the highest among previously reported absorbers based on Group IV materials and III-V compounds, overcoming the low solar absorption of such metasurfaces. The final proposed solar cell structure combines this meta-absorber layer with traditional efficiency enhancement methods namely anti-reflecting coating, textured back reflector, and transparent top electrode. This novel single junction structure shows a solar absorption efficiency of 97.86% and a power conversion efficiency of 30.87%, the highest for III-V solar cells. Our device proves the ability of metasurface absorber layers to produce high-efficiency solar cells and is expected to pave the way for integrating novel meta-devices into state-of-the-art photovoltaic devices, aiding the global transition towards clean energy sources.

Synthetic Approaches to Colloidal Nanocrystal Heterostructures Based on Metal and Metal-Oxide Materials

Composite inorganic nanoarchitectures, based on combinations of distinct materials, represent advanced solid-state constructs, where coexistence and synergistic interactions among nonhomologous optical, magnetic, chemical, and catalytic properties lay a basis for the engineering of enhanced or even unconventional functionalities. Such systems thus hold relevance for both theoretical and applied nanotechnology-based research in diverse areas, spanning optics, electronics, energy management, (photo)catalysis, biomedicine, and environmental remediation. Wet-chemical colloidal synthetic techniques have now been refined to the point of allowing the fabrication of solution free-standing and easily processable multicomponent nanocrystals with sophisticated modular heterostructure, built upon a programmed spatial distribution of the crystal phase, composition, and anchored surface moieties. Such last-generation breeds of nanocrystals are thus composed of nanoscale domains of different materials, assembled controllably into core/shell or heteromer-type configurations through bonding epitaxial heterojunctions. This review offers a critical overview of achievements made in the design and synthetic elaboration of colloidal nanocrystal heterostructures based on diverse associations of transition metals (with emphasis on plasmonic metals) and transition-metal oxides. Synthetic strategies, all leveraging on the basic seed-mediated approach, are described and discussed with reference to the most credited mechanisms underpinning regioselective heteroepitaxial deposition. The unique properties and advanced applications allowed by such brand-new nanomaterials are also mentioned.

Hybrid Nanocomposite Thin Films for Photovoltaic Applications: A Review

Continuing growth in global energy consumption and the growing concerns regarding climate change and environmental pollution are the strongest drivers of renewable energy deployment. Solar energy is the most abundant and cleanest renewable energy source available. Nowadays, photovoltaic technologies can be regarded as viable pathways to provide sustainable energy generation, the achievement attained in designing nanomaterials with tunable properties and the progress made in the production processes having a major impact in their development. Solar cells involving hybrid nanocomposite layers have, lately, received extensive research attention due to the possibility to combine the advantages derived from the properties of both components: flexibility and processability from the organic part and stability and optoelectronics features from the inorganic part. Thus, this review provides a synopsis on hybrid solar cells developed in the last decade which involve composite layers deposited by spin-coating, the most used deposition method, and matrix-assisted pulsed laser evaporation, a relatively new deposition technique. The overview is focused on the hybrid nanocomposite films that can use conducting polymers and metal phthalocyanines as p-type materials, fullerene derivatives and non-fullerene compounds as n-type materials, and semiconductor nanostructures based on metal oxide, chalcogenides, and silicon. A survey regarding the influence of various factors on the hybrid solar cell efficiency is given in order to identify new strategies for enhancing the device performance in the upcoming years.

Abnormal dewetting of Ag layer on three-dimensional ITO branches to form spatial plasmonic nanoparticles for organic solar cells

Three-dimensional (3D) plasmonic structures have attracted great attention because abnormal wetting behavior of plasmonic nanoparticles (NPs) on 3D nanostructure can enhance the localized surface plasmons (LSPs). However, previous 3D plasmonic nanostructures inherently had weak plasmonic light absorption, low electrical conductivity, and optical transmittance. Here, we fabricated a novel 3D plasmonic nanostructure composed of Ag NPs as the metal for strong LSPs and 3D nano-branched indium tin oxide (ITO BRs) as a transparent and conductive framework. The Ag NPs formed on the ITO BRs have a more dewetted behavior than those formed on the ITO films. We experimentally investigated the reasons for the dewetting behavior of Ag NPs concerning the geometry of ITO BRs. The spherical Ag NPs are spatially separated and have high density, thereby resulting in strong LSPs. Finite-domain time-difference simulation evidenced that spatially-separated, high-density and spherical Ag NPs formed on ITO BRs dramatically boost the localized electric field in the active layer of organic solar cells (OSCs). Photocurrent of PTB7:PCBM OSCs with the ITO BRs/Ag NPs increased by 14%.

Plasmon enhanced photocatalytic and antimicrobial activities of Ag-TiO2 nanocomposites under visible light irradiation prepared by DBD cold plasma treatment

Silver nanoparticles (Ag NPs) have been deposited on powder P25 by a novel two-step method involving a precipitation reaction and atmospheric pressure dielectric barrier discharge (DBD) cold plasma treatment without the use of any environmentally and biologically hazardous reducing agents. The silver precursor is formed in the processing of precipitation reaction and then completely reduced to the metallic state by atmospheric pressure DBD cold plasma treatment as proved by X-ray photoelectron spectroscopy, UV-Visible absorption spectra and HRTEM analyses. TEM images indicate that the Ag NPs with average diameter of 3.7 nm were deposited on powder P25 with high dispersion although no reducing agents, stabilizers or surfactants were used. The prepared products show remarkable improvement for methylene blue (MB) photodegradation and effective inhibition of bacterias against Escherichia coli and Staphylococcus aureus.

Enhanced Performance of Nanoporous Titanium Dioxide Solar Cells Using Cadmium Sulfide and Poly(3-hexylthiophene) Co-Sensitizers

This work reports the effect of co-sensitization of nanoporous titanium dioxide using Cadmium Sulfide (CdS) and poly(3-hexylthiophene) (P3HT) on the performance of hybrid solar cells. CdS nanolayer with different thicknesses was grown on Titanium Dioxide (TiO₂) nanoparticles by chemical bath deposition technique with varying deposition times. Both atomic force microscopy (AFM) and UV–Vis–NIR spectroscopy measurements of TiO₂ electrode sensitized with and without CdS layer confirm that the existence of CdS layer on TiO₂ nanoparticles. AFM images of CdS-coated TiO₂ nanoparticles show that the surface roughness of the TiO₂ nanoparticle samples decreases with increasing CdS deposition times. Current density–voltage and external quantum efficiency (EQE) measurements were carried out for corresponding solar cells. Both short circuit current density (J_SC) and fill factor were optimized at the CdS deposition time of 12 min. On the other hand, a steady and continuous increment in the open circuit voltage (V_OC) was observed with increasing CdS deposition time and increased up to 0.81 V when the deposition time was 24 min. This may be attributed to the increased gradual separation of P3HT and TiO₂ phases and their isolation at the interfaces. The higher V_OC of 0.81 V was due to the higher built-in voltage at the CdS–P3HT interface when compared to that at the TiO₂–P3HT interface. Optimized nanoporous TiO₂ solar cells with CdS and P3HT co-sensitizers showed external quantum efficiency (EQE) of over 40% and 80% at the wavelengths corresponding to strong absorption of the polymer and CdS, respectively. The cells showed an overall average efficiency of over 2.4% under the illumination of 70 mW/cm² at AM 1.5 condition.

Strong Enhancement of Photoelectric Conversion Efficiency of Co-hybridized Polymer Solar Cell by Silver Nanoplates and Core-Shell Nanoparticles

A new way was meticulously designed to utilize the localized surface plasmon resonance (LSPR) effect and the light scattering effect of silver nanoplate (Ag-nPl) and core-shell Ag@SiO₂ nanoparticles (Ag@SiO₂-NPs) to enhance the photovoltaic performances of polymer solar cells (PSCs). To prevent direct contact between silver nanoparticles (Ag-NPs) and photoactive materials which will cause electrons quenching, bare Ag-nPl were spin-coated on indium tin oxide and silica capsulated Ag-NPs were incorporated to a PBDTTT-C-T:PC₇₁BM active layer. As a result, the devices incorporated with Ag-nPl and Ag@SiO₂-NPs showed great enhancements. With the dual effects of Ag-nPl and Ag@SiO₂-NPs in devices, all wavelength sensitization in the visible range was realized; therefore, the power conversion efficiency (PCE) of PSCs showed a great enhancement of 14.0% to 8.46%, with an increased short-circuit current density of 17.23 mA·cm^-2. The improved photovoltaic performances of the devices were ascribed to the LSPR effect and the light scattering effect of metallic nanoparticles. Apart from optical effects, the charge collection efficiency of PSCs was improved after the incorporation of Ag-nPl.

Reduced Ensemble Plasmon Line Widths and Enhanced Two-Photon Luminescence in Anodically Formed High Surface Area Au-TiO2 3D Nanocomposites

Localized surface plasmon resonances (LSPR) in TiO₂ nanorod and nanotube arrays decorated by gold nanoparticles can be exploited to improve photocatalytic activity, enhance nonlinear optical coefficients, and increase light harvesting in solar cells. However, the LSPR typically has a low quality factor, and the resonance is often obscured by the Urbach tail of the TiO₂ band gap absorption. Attempts to increase the LSPR extinction intensity by increasing the density of gold nanoparticles on the surface of the TiO₂ nanostructures invariably produce peak broadening due to the effects of either agglomeration or polydispersity. We present a new class of hybrid nanostructures containing gold nanoparticles (NPs) partially embedded in nanoporous/nanotubular TiO₂ by performing the anodization of cosputtered Ti-Au thin films containing a relatively high ratio of Au:Ti. Our method of anodizing thin film stacks containing alternate layers of Ti and TiAu results in very distinctive LSPR peaks with quality factors as high as 6.9 and ensemble line widths as small as 0.33 eV even in the presence of an Urbach tail. Unusual features in the anodization of such films are observed and explained, including oscillatory current transients and the observation of coherent heterointerfaces between the Au NPs and anatase TiO₂. We further show that such a plasmonic NP-embedded nanotube structure dramatically outperforms a plasmonic NP-decorated anodic nanotube structure in terms of the extinction coefficient, and achieves a strongly enhanced two-photon fluorescence due to the high density of gold nanoparticles in the composite film and the plasmonic local field enhancement.

Light Manipulation in Organic Photovoltaics

Organic photovoltaics (OPVs) hold great promise for next-generation photovoltaics in renewable energy because of the potential to realize low-cost mass production via large-area roll-to-roll printing technologies on flexible substrates. To achieve high-efficiency OPVs, one key issue is to overcome the insufficient photon absorption in organic photoactive layers, since their low carrier mobility limits the film thickness for minimized charge recombination loss. To solve the inherent trade-off between photon absorption and charge transport in OPVs, the optical manipulation of light with novel micro/nano-structures has become an increasingly popular strategy to boost the light harvesting efficiency. In this Review, we make an attempt to capture the recent advances in this area. A survey of light trapping schemes implemented to various functional components and interfaces in OPVs is given and discussed from the viewpoint of plasmonic and photonic resonances, addressing the external antireflection coatings, substrate geometry-induced trapping, the role of electrode design in optical enhancement, as well as optically modifying charge extraction and photoactive layers.

Optimal Shell Thickness of Metal@Insulator Nanoparticles for Net Enhancement of Photogenerated Polarons in P3HT Films

Embedding metal nanoparticles in the active layer of organic solar cells has been explored as a route for improving charge carrier generation, with localized field enhancement as a proposed mechanism. However, embedded metal nanoparticles can also act as charge recombination sites. To suppress such recombination, the metal nanoparticles are commonly coated with a thin insulating shell. At the same time, this insulating shell limits the extent that the localized enhanced electric field influences charge generation in the organic medium. It is presumed that there is an optimal thickness which maximizes field enhancement effects while suppressing recombination. Atomic Layer Deposition (ALD) was used to deposit Al2O3 layers of different thicknesses onto silver nanoparticles (Ag NPs), in a thin film of P3HT. Photoinduced absorption (PIA) spectroscopy was used to study the dependence of the photogenerated P3HT(+) polaron population on the Al2O3 thickness. The optimal thickness was found to be 3-5 nm. This knowledge can be further applied in the design of metal nanoparticle-enhanced solar cells.

Synthesis of Water-Based Dispersions of Polymer/TiO₂ Hybrid Nanospheres

We develop a strategy for preparing water-based dispersions of polymer/TiO₂ nanospheres that can be used to form composite materials applicable in various fields. The formed hybrid nanospheres are monodisperse and possess a hierarchical structure. It starts with the primary TiO₂ nanoparticles of about 5 nm, which first assemble to nanoclusters of about 30 nm and then are integrated into monomer droplets. After emulsion polymerization, one obtains the water-based dispersions of polymer/TiO₂ nanospheres. To achieve universal size, it is necessary to have treatments with intense turbulent shear generated in a microchannel device at different stages. In addition, a procedure combining synergistic actions of steric and anionic surfactants has been designed to warrant the colloidal stability of the process. Since the formed polymer/TiO₂ nanospheres are stable aqueous dispersions, they can be easily mixed with TiO₂-free polymeric nanoparticle dispersions to form new dispersions, where TiO₂-containing nanospheres are homogeneously distributed in the dispersions at the nanoscale, thus leading to various applications. As an example, the proposed strategy has been applied to generate polystyrene/TiO₂ nanospheres of about 100 nm in diameter.

Plasmonic effect of spray-deposited Au nanoparticles on the performance of inverted organic solar cells

Gold nanoparticles with varying sizes were prepared by the spray process under an electric field (DC voltages of 0 V and 1 kV applied to the nozzle) for studying their role in inverted organic solar cells (ITO/Au/ZnO/P3HT:PCBM/Ag). The application of electric field during the spray process resulted in a smaller size (35 nm as compared to 70 nm without the electric field) of the nanoparticles with more uniform distribution. This gave rise to a difference in the surface plasmon resonance (SPR) effect created by the gold nanoparticles (Au NPs), which then affected the solar cell performance. The photovoltaic performances of plasmonic inverted organic solar cells (ITO/Au/ZnO/P3HT:PCBM/Ag) using spray-deposited Au and ZnO layers (both at 1 kV) showed improved efficiency. Fast exciton quenching in the P3HT:PCBM layer was achieved by using a spray-deposited Au layer in between ITO and ZnO layers. The absorption spectra and internal power conversion efficiency (IPCE) curve showed that the Au nanoparticles provide significant plasmonic broadband light absorption enhancement which resulted in the enhancement of the JSC value. Maximum efficiency of 3.6% was achieved for the inverted organic solar cell (IOSC) with an exceptionally high short circuit current density of ∼15 mA cm(-2) which is due to the additional photon absorption and the corresponding increase observed in the IPCE spectrum. The spray technique can be easily applied for the direct formation of Au nanoparticles in the fabrication of IOSC with improved performance over a large area.