Polymer-Derived Ceramic Nanoparticle/Edge-Functionalized Graphene Oxide Composites for Lithium-Ion Storage

Polymer-derived ceramics demonstrate great potential as lithium-ion battery anode materials with good cycling stability and large capacity. SiCNO ceramic nanoparticles are produced by the pyrolysis of polysilazane nanoparticles that are synthesized via an oil-in-oil emulsion crosslinking and used as anode materials. The SiCNO nanoparticles have an average particle size of around 9 nm and contain graphitic carbon and Si₃N₄ and SiO₂ domains. Composite anodes are produced by mixing different concentrations of SiCNO nanoparticles, edge-functionalized graphene oxide, polyvinylidenefluoride, and carbon black Super P. The electrochemical behavior of the anode is investigated to evaluate the Li-ion storage performance of the composite anode and understand the mechanism of Li-ion storage. The lithiation of SiCNO is observed at ∼0.385 V versus Li/Li⁺. The anode has a large capacity of 705 mA h g^-1 after 350 cycles at a current density of 0.1 A g^-1 and shows an excellent cyclic stability with a capacity decay of 0.049 mA h g^-1 (0.0097%) per cycle. SiCNO nanoparticles provide a large specific area that is beneficial to Li⁺ storage and cyclic stability. In situ transmission electron microscopy analysis demonstrates that the SiCNO nanoparticles exhibit extraordinary structural stability with 9.36% linear expansion in the lithiation process. The X-ray diffraction and X-ray photoelectron spectroscopy investigation of the working electrode before and after cycling suggests that Li⁺ was stored through two pathways in SiCNO lithiation: (a) Li-ion intercalation of graphitic carbon in free carbon domains and (b) lithiation of the SiO₂ and Si₃N₄ domains through a two-stage process.

A ZnS nanocrystal/reduced graphene oxide composite anode with enhanced electrochemical performances for lithium-ion batteries

A simple route for the preparation of ZnS nanocrystal/reduced graphene oxide (ZnS/RGO) by a hydrothermal synthesis process was achieved. The chemical composition, morphology, and structural characterization reveal that the ZnS/RGO composite is composed of sphalerite-phased ZnS nanocrystals uniformly dispersed on functional RGO sheets with a high specific surface area. The ZnS/RGO composite was utilized as an anode in the construction of a high-performance lithium-ion battery. The ZnS/RGO composite with appropriate RGO content exhibits a high reversible specific capacity (780 mA h g^-1), excellent cycle stability over 100 cycles (71.3% retention), and good rate performance at 2C (51.2% of its capacity when measured at a 0.1C rate). To further investigate this ZnS/RGO anode for practical use in full Li-ion cells, we tested the electrochemical performance of the ZnS/RGO anode at different cut-off voltages for the first time. The presence of RGO plays an important role in providing high conductivity as well as a substrate with a high surface area. This helps alleviate the typically problems associated with volume expansion and shrinkage during prolonged cycling. Additionally, the RGO provides multiple nucleation points that result in a uniformly dispersed film of nanosized ZnS that covers its surface. Thus, the high surface area RGO enables high electronic conductivity and fast charge transfer kinetics for ZnS lithiation/delithiation.

A new strategy to address the challenges of nanoparticles in practical water treatment: mesoporous nanocomposite beads via flash freezing

Various engineering nanoparticles (NPs) exhibit high reactivity and great potential for water decontamination. Encapsulation of NPs into millimeter-sized polymer hosts is a very promising strategy to address their inherent bottlenecks for scale-up water treatment such as aggregation, difficult operation and potential risks when released into water. However, the inevitable host pore blockage accompanying NP loadings significantly compromise their decontamination reactivity. Herein, a newly developed flash freezing method was utilized to embed α-Fe₂O₃ NPs (3 nm, 7 nm and 18 × 90 nm) inside millimetric polystyrene to prepare mesoporous nanocomposites Fe₂O₃@PS. All the as-obtained Fe₂O₃@PS nanocomposites feature high mesoporosity, well-dispersed NPs and highly accessible sites. The amount of Fe-OH species, i.e., the active sites for As(v) sequestration, of the embedded 3 nm-Fe₂O₃ is dramatically increased 3.6 times over the bare NPs, resulting in higher adsorption capacity and affinity. The 3 nm-Fe₂O₃@PS is capable of producing clean water 2000-fold greater in mass successively in column adsorption, with As(v) reducing from 176 μg L^-1 initially to <1 μg L^-1. Also, Fe₂O₃@PS can be readily regenerated for cyclic use with negligible NPs leaking into water. This study provides an elaborate strategy to address the trade-off between easy operation and decontamination reactivity of NPs for water treatment.

Preparation and Capacity-Fading Investigation of Polymer-Derived Silicon Carbonitride Anode for Lithium-Ion Battery

Polymer-derived silicon carbonitride (SiCN) materials have been synthesized via pyrolyzing from five poly(silylcarbondiimide)s with different contents of carbon (labeled as 1-5#). The morphological and structural measurements show that the SiCN materials are mixtures of nanocrystals of SiC, Si₃N₄, and graphite. The SiCN materials have been used as anodes for lithium-ion batteries. Among the five polymer-derived SiCN materials, 5#SiCN, derived from dichloromethylvinylsilane and di-n-octyldichlorosilane, has the best cycle stability and a high-rate performance at the low cutoff voltage of 0.01-1.0 V. In lithium-ion half-cells, the specific delithiation capacity of 5#SiCN anode still remains at 826.7 mA h g^-1 after 100 charge/discharge cycles; it can even deliver the capacity above 550 mA h g^-1 at high current densities of 1.6 and 2 A g^-1. In lithium-ion full cells, 5#SiCN anode works well with LiNi_0.6Co_0.2Mn_0.2O₂ commercial cathode. The outstanding electrochemical performance of 5#SiCN anode is attributed to two factors: (1) the formation of a stable and compact solid electrolyte interface layer on the anode surface anode, which protects the electrode from cracking during the charge/discharge cycle; and (2) a large amount of carbon component and the less Si₃N₄ phase in the 5#SiCN structure, which provides an electrochemical reactive and conductive environment in the SiCN structure, benefit the lithiation/delithiation process. In addition, we explore the reason for the capacity fading of these SiCN anodes.

High rate capabilities of HF-etched SiOC anode materials derived from polymer for lithium-ion batteries

Polymer-derived silicon oxycarbide (SiOC) composites have recently attracted considerable attention because of their potential as high capacity electrode for rechargeable lithium ion batteries.