Ambient Air Purification by Nanotechnologies: From Theory to Application

Air pollution has been a recurring problem in northern Chinese cities, and high concentrations of PM2.5 in winter have been a particular cause for concern. Secondary aerosols converted from precursor gases (i.e., nitrogen oxides and volatile organic compounds) evidently account for a large fraction of the PM2.5. Conventional control methods, such as dust removal, desulfurization, and denitrification, help reduce emissions from stationary combustion sources, but these measures have not led to decreases in haze events. Recent advances in nanomaterials and nanotechnology provide new opportunities for removing fine particles and gaseous pollutants from ambient air and reducing the impacts on human health. This review begins with overviews of air pollution and traditional abatement technologies, and then advances in ambient air purification by nanotechnologies, including filtration, adsorption, photocatalysis, and ambient-temperature catalysis are presented—from fundamental principles to applications. Current state-of-the-art developments in the use of nanomaterials for particle removal, gas adsorption, and catalysis are summarized, and practical applications of catalysis-based techniques for air purification by nanomaterials in indoor, semi-enclosed, and open spaces are highlighted. Finally, we propose future directions for the development of novel disinfectant nanomaterials and the construction of advanced air purification devices.

Oxidative Inactivation of SARS-CoV-2 on Photoactive AgNPs@TiO2 Ceramic Tiles

The current SARS-CoV-2 pandemic causes serious public health, social, and economic issues all over the globe. Surface transmission has been claimed as a possible SARS-CoV-2 infection route, especially in heavy contaminated environmental surfaces, including hospitals and crowded public places. Herein, we studied the deactivation of SARS-CoV-2 on photoactive AgNPs@TiO₂ coated on industrial ceramic tiles under dark, UVA, and LED light irradiations. SARS-CoV-2 inactivation is effective under any light/dark conditions. The presence of AgNPs has an important key to limit the survival of SARS-CoV-2 in the dark; moreover, there is a synergistic action when TiO₂ is decorated with Ag to enhance the virus photocatalytic inactivation even under LED. The radical oxidation was confirmed as the the central mechanism behind SARS-CoV-2 damage/inactivation by ESR analysis under LED light. Therefore, photoactive AgNPs@TiO₂ ceramic tiles could be exploited to fight surface infections, especially during viral severe pandemics.

Bismuth Oxyhalides for NOx Degradation under Visible Light: The Role of the Chloride Precursor

Photocatalysis is a green technology for tackling water and air contamination. A valid alternative to the most exploited photocatalytic material, TiO2, is bismuth oxyhalides, which feature a wider bandgap energy range and use visible radiation to attain photoexcitation. Moreover, their layered structure favors the separation of photogenerated electron–hole pairs, with an enhancement in photocatalytic activity. Controlled doping of bismuth oxyhalides with metallic bismuth nanoparticles allows for further boosting of the performance of the material. In the present work, we synthesized Y%Bi-doped BiO(Cl0.875Br0.125) (Y = 0.85, 1, 2, 10) photocatalysts, using cetyltrimethylammonium bromide as the bromide source and varying the chloride source to assess the impact that both length and branching of the hydrocarbon chain might have on the framing and layering of the material. A change in the amount of the reducing agent NaBH4 allowed tuning of the percentage of metallic bismuth. After a thorough characterization (XRPD, SEM, TEM, UV-DRS, XPS), the photocatalytic activity of the catalysts was tested in the degradation of NOx under visible light, reaching a remarkable 53% conversion after 3 h of illumination for the material prepared using cetylpyridinium chloride.

Experimental and Computational Analysis of NOx Photocatalytic Abatement Using Carbon-Modified TiO2 Materials

In the present study, two photocatalytic graphene oxide (GO) and carbon nanotubes (CNT) modified TiO2 materials thermally treated at 300 °C (T300_GO and T300_CNT, respectively) were tested and revealed their conversion efficiency of nitrogen oxides (NOx) under simulated solar light, showing slightly better results when compared with the commercial Degussa P25 material at the initial concentration of NOx of 200 ppb. A chemical kinetic model based on the Langmuir–Hinshelwood (L-H) mechanism was employed to simulate micropollutant abatement. Modeling of the fluid dynamics and photocatalytic oxidation (PCO) kinetics was accomplished with computational fluid dynamics (CFD) approach for modeling single-phase liquid fluid flow (air/NOx mixture) with an isothermal heterogeneous surface reaction. A tuning methodology based on an extensive CFD simulation procedure was applied to adjust the kinetic model parameters toward a better correspondence between simulated and experimentally obtained data. The kinetic simulations of heterogeneous photo-oxidation of NOx carried out with the optimized parameters demonstrated a high degree of matching with the experimentally obtained NOx conversion. T300_CNT is the most active photolytic material with a degradation rate of 62.1%, followed by P25-61.4% and T300_GO-60.4%, when irradiated, for 30 min, with emission spectra similar to solar light.

Photocatalytic porcelain grés large slabs digitally coated with AgNPs-TiO2

TiO₂ is employed as both photocatalytic and structural materials, leading to its applications in external coatings or in interior furnishing devices, including cement mortar, tiles, floorings, and glass supports. The authors have already demonstrated the efficiency of photoactive micro-sized TiO₂ and here its industrial use is reported using the digital printing to coat porcelain grés slabs. Many advantages are immediately evident, namely rapid and precise deposition, no waste of raw materials, thus positively affecting the economy of the process. Data for the thin films deposited by digital printing were compared with those obtained for the conventional spray method. The use of metal-doped TiO₂ is also reported so that the photoactivity of these materials can be exploited even under LED light. The digital inkjet printed coatings exhibited superior photocatalytic performance owing to both higher exposed surface area and greater volume of deposited anatase, as well as the greater areal distribution density of thinly and thickly coated regions. Moreover, the presence of TiO₂ doped silver increased the efficiency of the materials in NOx degradation both under UVA and LED lights.