In Situ Real-Time Quantitative Characterization of Nanofiltration Membrane Pore Orientation for Enhanced Ion Separation

Nanofiltration membranes hold great promise for ion separation but often suffer from a trade-off between selectivity and flux, limiting their use in precise separation processes. A key challenge is achieving precise control over pore orientation, as existing methods fail to provide real-time, quantitative insights for optimizing membrane structure and performance. To address this, an innovative in situ, real-time quantitative technique is developed that links pore alignment directly to separation efficiency. Using β-cyclodextrin as a model pore-forming compound, fluorescent labeling enables continuous monitoring of pore orientation and distribution during membrane fabrication. This method enables the capture of the complete distribution of pore orientation across the entire membrane surface, allowing for precise adjustments in membrane design. This approach provides the real-time quantification of pore alignment, facilitating the design of NF membranes with enhanced ion selectivity and permeability. The optimized membranes demonstrate exceptional Mg2+/Li+ separation efficiency, with a separation factor of 15.55 and permeance of 35.85 L m-2 h-1 bar-1, representing a significant step forward in high-performance nanofiltration membranes with broad applications in resource recovery, environmental remediation, and water treatment.

Synergistic heterojunction effects in Ag3PO4/SnO2 nanocomposites: a photocatalytic study on isoproturon degradation

Introduction

Pesticides such as isoproturon are widely employed and represent a considerable environmental concern. The development of sustainable and efficient degrading techniques is crucial. Photocatalytic degradation employing semiconductor materials is a compelling solution. This study examines the synergistic advantages of heterojunction formation by synthesizing, characterizing, and improving the photocatalytic efficacy of Ag3PO4/SnO2 nanocomposites for the degradation of isoproturon.

Methods

The Ag3PO4/SnO2 nanocomposite was characterised using powder X-ray diffraction (PXRD), Fourier Transform Infrared Spectroscopy (FTIR), Scanning Electron Microscopy (SEM), Ultraviolet-Diffuse Reflectance Spectroscopy (UV-DRS) and X-ray Photoelectron Spectroscopy (XPS). The effective synthesis of the Ag3PO4/SnO2 heterojunction was confirmed by characterization data from various techniques (PXRD, FTIR, SEM, UV-DRS, XPS).

Results and Discussion

Elemental mapping confirmed uniform distribution of O, P, Ag, and Sn. High-resolution mass spectrometry (HRMS) was employed to analyse degradation products. The Ag3PO4/SnO2 nanocomposite exhibited improved photocatalytic degradation of isoproturon compared to its precursors. In contrast to 25% for pure SnO2 and 41% for Ag3PO4, over 97% degradation was achieved using Ag3PO4/SnO2 nanocomposite within 120 min of light irradiation under identical conditions. The synergistic effects of heterojunction formation significantly enhanced isoproturon degradation using the Ag3PO4/SnO2 nanocomposite. The heterojunction reduces electron-hole recombination rate and enhances photogenerated charge carriers for degradation via effective charge separation. The improved photocatalytic activity is ascribed to the increased surface area of the nanocomposite. The analysis of HRMS data revealed the degradation products. The findings demonstrate the efficacy of Ag3PO4/SnO2 nanocomposites as photocatalysts for environmental remediation, namely in the breakdown of pesticides.

How Local Order Leads to Shape Selectivity in Disordered Materials: The Case of FAU-FER Interzeolite Transformation Intermediates

This study presents a series of Interzeolite Transformation Intermediates (ITIs) derived from FAU-to-FER interconversion. These hybrid materials, obtained through precise control of the interconversion process, exhibit both large mesoporosity and FER topology-type pore confinement, resulting in high conversion and remarkable shape selectivity despite their disordered structure at the long range. We demonstrated this unique combination of properties in three different catalytic tests. The local order within these ITIs is sufficient to create pore confinement, which not only produces remarkable shape selectivity but also enhances conversion by increasing accessibility. Specifically, the ITIs show a 10-fold increase in activity for Friedel-Crafts alkylation, a 16-fold increase in activity for triisopropylbenzene (TiPBz) cracking, and a two-fold increase in methanol dehydration to dimethyl ether (DME) compared to commercial ferrierite all while maintaining the selectivity of FER. These results highlight the potential of FAU-to-FER ITIs as high-performance catalysts that combine the accessibility of disordered structures with the selectivity typically associated with well-ordered zeolites, opening avenues in zeolite-based catalysis.

Ethylene oligomerization to liquid fuels over steam and phosphorus modified MFI zeolites

A series of steam and phosphorus modified ZSM-5 samples were prepared to investigate the effect of pore structure and acid property on ethylene oligomerization. Characterization results showed that steam treatment contributed to generate mesopores with pore sizes of 2-3 nm and 10-20 nm, while progressive aggregation of phosphorus species on the exterior surface resulted in blockage of channels. Dealumination of framework aluminum led to a gradual decline in total acidity and acid strength with an increase of steam temperature or P/Al ratio. Sufficient strong acid sites and enhanced accessibility to the inner active sites were crucial factors in conversion of ethylene to liquid fuels. The steam modified sample at 700 °C (HZ-700) obtained the highest yield of liquid fuels up to 78.1%, which demonstrated an increase of 40% in comparison with the unmodified sample. Due to improved diffusional capacity originating from mesopores, HZ-700 showed a higher deactivation stability than the phosphorus modified sample at similar conversion levels. This work will provide some insight into the development of zeolite-based catalyst for ethylene oligomerization to liquid fuels.

Investigating the Correlation of Morphology with the N2 Physisorption Behavior of Al-Incorporated bcl Silica

We report the synthesis of Al-incorporated bicontinuous concentric lamellar (bcl) silica particles with mesoporous-scale pores, high pore volume, and high surface area through the reflux method at atmospheric pressure. This study demonstrates that bcl morphology can be achieved by carefully tuning reaction parameters such as reflux time, temperature, and surfactant type. The aluminum (Al) precursor concentration significantly influences the formation of Al-incorporated bcl silica, while the NaOH concentration has no significant impact. Scanning electron microscope (SEM) images show that synthesis at 130 °C for 20 h using the CTAB (cetyltrimethylammonium bromide) surfactant and 1 mol sodium aluminate produced a spherical silica bcl-like morphology surrounded by lamellae. These SEM images are supported by the N2 physisorption isotherm pattern, which follows type IVa with an H3 hysteresis loop, indicating slit-like particle aggregates. Exceeding 3 mol of aluminum prevents bcl morphology formation, with the hysteresis pattern shifting to type H2, indicative of pore blocking. This study provides a reference for the development of Al-incorporated bcl silica into zeolite with bcl morphology.

A new determination of group-modified pore size distribution of activated carbon from confined density distribution

The two-distribution model is developed to determine the group-modified pore size distribution (PSD) of activated carbon, where the PSD is modified by the group distribution. This model assumes an ensemble composed of the elementary confined density distribution for fluids and the group-modified PSD for activated carbon. The group-modified PSD is derived by fitting the theoretical adsorption, calculated using the two-distribution model with grand canonical Monte Carlo simulation-dependent kernels of the N2 isotherm at 77.4 K and a single CO2 adsorption data point at 273.0 K, to experimental adsorption data for activated carbon. The group-modified PSD is validated against adsorption data for seven fluids on various activated carbons. In this analysis, the adsorption isotherms calculated using the two-distribution model with PSD, homogeneous group-modified PSD, and inhomogeneous group-modified PSD are compared and evaluated. The results show that the two-distribution model accurately interprets the group-modified PSD.

Nanoconfinement-Driven Energy-Efficient CO2 Capture and Release at High Pressures on a Unique Large-Pore Mesoporous Carbon

Although microporous carbons can perform well for CO2 separations under high pressure conditions, their energy-demanding regeneration may render them a less attractive material option. Here, we developed a large-pore mesoporous carbon with pore sizes centered around 20-30 nm using a templated technical lignin. During the soft-templating process, unique cylindrical supramolecular assemblies form from the copolymer template. This peculiar nanostructuring takes place due to the presence of polyethylene glycol (PEG) segments on both the Pluronic® template and the PEG-grafted lignin derivative (glycol lignin). A large increase in CO2 uptake occurs on the resulting large-pore mesoporous carbon at 270 K close to the saturation pressure (3.2 MPa), owing to capillary condensation. This phenomenon enables a CO2/CH4 selectivity (SCO2/CH4, mol/mol) of 3.7 at 270 K and 3.1 MPa absolute pressure, and a swift pressure swing regeneration process with desorbed CO2 per unit pressure far outperforming a benchmark activated carbon (i.e., notably rapid decrease in the amount of adsorbed CO2 with decreasing pressure). We propose large-pore mesoporous carbons as a novel family of CO2 capture adsorbents, based on the phase-transition behavior shift of CO2 in the nanoconfined environment. This novel material concept may open new horizons for physisorptive CO2 separations with energy-efficient regeneration options.

Amino Acid-Assisted Synthesis of Zeolites with Improved Catalytic Properties

Conventional zeolites are limited in their ability to catalyze macromolecular reactions due to micropore constraints, resulting in sluggish reactant and product diffusion and subsequently pore clogging and catalyst deactivation. Consequently, the pore and textural refinement of zeolites to meet industrial demands has become a research hotspot. Herein, we review the amino acid-assisted methods in zeolite synthesis and scrutinize the principle and influential factors governing amino acid involvement in zeolite synthesis. Additionally, we analyze the advantages and challenges associated with the amino acid-assisted method. Certain amino acids can interact with zeolite precursors or crystal surface, thus altering the crystal growth rate and enabling precise control over the crystal size and shape. On the other hand, amino acids can serve as structure-directing agents to orchestrate the generation of mesoporous pores. These capabilities enable the production of zeolites with well-defined pores, particle sizes and/or crystal shapes that satisfy catalytic requirements. Moreover, the unique properties of amino acids allow their complete elimination from the solid product through a simple aqueous washing process, facilitating their recovery for subsequent usage. As result, the amino acid-assisted synthesis methods offer a convenient, green route to zeolites with modulated textual properties for high-performance catalysis.

Surface areas and adsorption energies of biochars estimated from nitrogen and water vapour adsorption isotherms

Nitrogen adsorption isotherms, along with the BET model for interpretation, are recommended for estimating biochar surface area. The frequently measured small surface areas of biochars contrast with their high sorption and cation exchange capacities. We hypothesised that water adsorption provides a better tool for estimating the surface area of biochars. Although adsorption energy also appears to be a valuable surface characteristic, there is a lack of studies on this subject. We studied the surface areas and adsorption energies of three waste deposits - peat, willow dust and biochar prepared from these materials at different temperatures - using nitrogen and water vapour adsorption isotherms. The BET model accurately described all water vapour adsorption isotherms but failed for some nitrogen isotherms. Alternative methods for estimating surface areas and adsorption energies were proposed in cases where the BET model did not apply. Nitrogen adsorption was typically much lower than water vapour adsorption, and the estimated surface areas reflected this. However, nitrogen adsorption energies were significantly higher. Nitrogen surface areas increased with pyrolysis temperature, while water vapour surface areas decreased. The surface area estimated from nitrogen adsorption was generally much lower than needed to accommodate the surface-charged groups responsible for the cation exchange capacity of biochars.

Hierarchically spherical assembly of carbon nanorods derived from metal-organic framework as solid-phase microextraction coating for nitrated polycyclic aromatic hydrocarbon analysis

Nitrated polycyclic aromatic hydrocarbons (nitro-PAHs) are pervasive contaminants in aquatic environments. They are characterized by persistence, toxicity, bioaccumulation, and long-range transport, significantly threatening human health. The development of sensitive methods for nitro-PAH analysis in environmental samples is in great need. This study developed a novel carbonaceous SPME coating derived from metal-organic framework (MOF), namely a spherical assembly consisting of carbon nanorods with hierarchical porosity (HP-MOF-C), for the extraction and determination of nitro-PAHs in waters. The HP-MOF-C coated fiber demonstrated superior nitro-PAH extraction efficiencies, with enrichment factors 2∼70 times higher than commercial fibers. This enhancement was due to the strong hydrophobic, π-π electron coupling/stacking, and π-π electron donor-acceptor interactions between the carbonaceous framework of HP-MOF-C and the nitro-PAHs. Moreover, the unique hierarchical porous structure of HP-MOF-C accelerated the diffusion of nitro-PAHs, further facilitating their enrichment. The fiber also exhibited good thermal stability, remarkable chemical stabilities against common acid, base, and polar/non-polar solvents, and long service life (> 150 SPME cycles). The nitro-PAH determination method based on HP-MOF-C coating yielded wide linear ranges, low detection limits (0.4∼5.0 ng L-1), satisfactory repeatability and reproducibility, and good recoveries in real water samples. The proposed method was considered to be green according to the Analytical GREEnness assessment. The present study not only offers an efficient SPME coating for the enrichment of nitro-PAHs, but also provides insights into the design of porous coating materials.

Development and Application of an Advanced Percolation Model for Pore Network Characterization by Physical Adsorption

Physical adsorption is one of the most widely used techniques to characterize porous materials because it is reliable and able to assess micro- and mesopores within one approach. Challenges and open questions persist in characterizing disordered and hierarchically structured porous materials. This study introduces a pore network model aimed at enhancing the textural characterization of nanoporous materials. The model, based on percolation theory on a finite-sized Bethe lattice, includes all mechanisms known to contribute to adsorption hysteresis in mesoporous pore networks. The model accounts for delayed and initiated condensation during adsorption as well as equilibrium evaporation, pore blocking, and cavitation during desorption. Coupled with dedicated nonlocal-density functional theory kernels, the proposed method provides a unified framework for modeling the entire experimental adsorption-desorption isotherm, including desorption hysteresis scans. The applicability of the method is demonstrated on a selected set of nanoporous silica materials exhibiting distinct types of hysteresis loops (types H1, H2a, H1/H2a, and H5), including ordered mesoporous silica networks (KIT-6 and SBA-15/MCM-41 hybrid silica with plugged pores) and disordered mesoporous silica networks (hierarchical meso-macroporous monolith and porous Vycor glass). For all materials, a good correlation is found between calculated and experimental primary isotherms as well as desorption scans. The model allows us to determine key pore network characteristics such as pore connectivity and pore size distributions as well as a parameter correlated with the impact of pore network disorder on the adsorption behavior. The versatility and enriched textural insights provided by the proposed novel network model allow for a comprehensive characterization previously inaccessible and hence will contribute to further advancement in the textural characterization of novel nanoporous materials. It has the potential to provide important guidance for the design and selection of porous materials for optimizing various applications, including separation processes such as chromatography, heterogeneous catalysis and gas and energy storage.

Flexible Mesopores in Nanoscrolls: Extraordinarily Large Alteration of Pore Sizes and Their Reversibility

Flexible porous materials have gained considerable interest for their potential applications in selective absorption and controlled release/storage of specific molecules or compounds. Here, nanoscrolls are proposed as a type of inorganic solids with reversibly flexible mesopores. Nanoscrolls exhibit a rolled-up structure composed of nanosheets with a 1D rod-like morphology, possessing two distinct nanospaces. The first space comprises 1D tubular mesopores located at the center of the rod, while the second space exists in the interlayer regions on the wall of the mesopore, resulting from the layer stacking caused by the scrolling of nanosheets. By replacing the interlayer cations on the nanoscroll walls with other cations, a drastic alteration in the size of the 1D mesopores is observed. For instance, exchanging bulky dodecylammonium cations with small NH4 + cations leads to a substantial change in pore size, with differences ranging from 10 to 20 nm-a notably larger variation compared to previous reports on flexible porous materials. Importantly, the alteration of pore size induced by the exchange reaction is found to be reversible. This reversible alteration in pore size holds promise for applications in host-guest chemistry involving large moieties such as nanoparticles and enzymes.

Renewable Resources as Promising Materials for Obtaining Graphene Oxide-like Structures

Currently, one of the topical directions in the field of production and application of graphene-like nanostructures is the use of renewable natural raw materials, which have unlimited resources for an economically efficient large-scale yield of a product with environmental safety. In this regard, we present the production of graphene oxide (GO) from a renewable natural raw material of plant biomass, birch activated carbon (BAC), and a comparison of the obtained physicochemical, mechanical, and electrical properties of birch activated carbon-graphene oxide (BAC-GO) and graphite-graphene oxide (G-GO) synthesized from the initial materials, BAC and graphite (G). Results obtained from this study confirm the successful oxidation of BAC, which correlates well with the physical-chemical dates of the G-GO and BAC-GO samples. Change in data after the oxidation of graphite and BAC was facilitated by the structure of the starting materials and, presumably, the location and content of functional oxygen-containing groups in the G-GO and BAC-GO chains. Based on the results, the application of a cost-effective, eco-friendly colloidal solution of nanodispersed BAC-GO from a plant biomass-based high-quality resource for producing large-scale nanostructured graphene is validated which has potential applicability in nanoelectronics, medicine, and other fields.

Hydrochars derived from real organic wastes as carbonaceous precursors of activated carbons for the removal of NO from contaminated gas streams

The improvement of air quality in densely-populated urban regions constitutes an environmental challenge of increasing concern. In this respect, the abatement of NO emissions, primarily emanating from combustion processes associated with motor-vehicles, along with industrial/domestic combustion systems, represents one of the main problems. Here, three hydrochars from diverse organic residues were used as activated carbon precursors for their evaluation in the NO removal in two potential application scenarios. Hydrochars were physically activated at 800 °C with pure-CO2 or diluted-O2. These materials were tested in a lab-scale biofilter at different conditions (NO concentration, temperature, relative humidity, NO-containing gas and carbon particle size) and in a larger-scale biofilter to evaluate the long-term NO removal capacity. Hydrochar-derived carbons present a relatively well-developed micro- and mesoporous structure, with BET areas of up to 421 m2/g, and a variety of oxygen surface functionalities (carboxylic, lactone, carbonyl and quinone groups), especially concerning CO2-activated carbons. These exhibited an excellent behaviour at low NO concentration (5 ppmv) between 25 and 75 °C with removal capacities of ≈97 % and > 82 %, respectively; and still good-performance (≈66 %) in a more concentrated gas (120 ppmv). Whilst, carbons obtained by diluted-O2 activation from the same hydrochars, evidenced a higher removal capacity loss at high NO concentration. The O2 presence in the gas stream was confirmed as a crucial factor in the NO elimination, since both co-adsorb on the carbon surface favouring NO oxidation to NO2. Besides, the humidity in the airstream diminished the NO removal capacity from 0.88 to 0.51 mgNO/gcarbon, but still remained at 0.54 mgNO/gcarbon, when the carbon (in pellet) was operated at larger-scale biofilter in 9-fold longer test under humid air. Therefore, this study highlights the potential of renewable carbons to serve as cost-effective component in urban biofilters, to mitigate NO emissions from exhaust gases in biomass boilers and urban semi-close areas.

(Ga1-xAlx)4B2O9: controlled surface acid-base properties and catalytic behavior towards the Strecker reaction

Solid bases are valuable catalysts for industrial syntheses. However, controlling the basicity of these catalysts remains a challenge. Ga4B2O9, due to μ3-O within its structure, could behave as a special solid base catalyst exhibiting intrinsic Lewis basicity. In this work, a sol-gel method was proposed to obtain continuously adjustable acidity and basicity of the metal borate catalyst (AlxGa1-x)4B2O9. According to the results of NH3-TPD, CO2-TPD, and the systematic experimental design, Lewis basic sites originating from GaO5 groups in (AlxGa1-x)4B2O9 boost the Strecker reaction rather than the Lewis acid sites related to unsaturated Al. This work illustrates the possible application of bulk-type solid solutions with simultaneous Lewis acid and base sites for the first time. A reaction mechanism has also been proposed based on the catalytic reaction results.

One-Pot Synthesis of Biochar from Industrial Alkali Lignin with Superior Pb(II) Immobilization Capability

This study synthesized biochar through a one-pot pyrolysis process using IALG as the raw material. The physicochemical properties of the resulting biochar (IALG-BC) were characterized and compared with those of biochar derived from acid-treated lignin with the ash component removed (A-IALG-BC). This study further investigated the adsorption performances and mechanisms of these two lignin-based biochars for Pb(II). The results revealed that the high ash content in IALG, primarily composed of Na, acts as an effective catalyst during pyrolysis, reducing the activation energy and promoting the development of the pore structure in the resulting biochar (IALG-BC). Moreover, after pyrolysis, Na-related minerals transformed into particulate matter sized between 80 and 150 nm, which served as active adsorption sites for the efficient immobilization of Pb(II). Adsorption results demonstrated that IALG-BC exhibited a significantly superior adsorption performance for Pb(II) compared to that of A-IALG-BC. The theoretical maximum adsorption capacity of IALG-BC for Pb(II), derived from the Langmuir model, was determined to be 809.09 mg/g, approximately 40 times that of A-IALG-BC. Additionally, the adsorption equilibrium for Pb(II) with IALG-BC was reached within approximately 0.5 h, whereas A-IALG-BC required more than 2 h. These findings demonstrate that the presence of inorganic mineral components in IALG plays a crucial role in its resource utilization.

Encapsulation of Cu-modified SnO2 yolk-shell in V2O5-amalgamated wrinkled g-C3N4 lamella for boosting antibiotic photodegradation

The remarkable application of tin oxide in various domains is indebted to its photoelectronic merits. However, significant efforts to discover its photocatalytic potential were restricted through arduous challenges, which were the amelioration of light-harvesting and -utilizing. In fact, the uncommon light absorption energy has drawn veil over the brilliance of astounding oxidation potential, which is much more than that of TiO2. Herein, our attention was focused on the taking advantages of self-template structure for simultaneously enjoying the two sides of photoelectronic justification as well as the S-step system for eminent charge dissociation. In this regard, the optimized Cu-modified SnO2 yolk-shell ((5)YS-CuSnO) spheres were engineered through the copper modulation into glycerate-assisted metal-organic structure. As a result, the exceptional light-harvesting was achieved through desirable defects and oxygen vacancy resulted from Cu-doping, and also efficient light-utilization was obtained by the multi-scattering/reflection effect resulted from multi-shell configuration. After the effectual incorporation (40 wt⁒) of (5)YS-CuSnO was encapsulated into the V2O5-decorated wrinkled g-C3N4 lamella (VO-WCN), the dual S-step VO-WCN@(5)YS-CuSnO introduced unprecedented levofloxacin (LFC) decontamination performance, which was kinetically 5.2 and 30.2-times greater than of the (5)YS-CuSnO and bare SnO2 yolk-shell. The conspicuous fulfillment of nanocomposite was manifested in the LFC mineralization, pharmaceutical effluent treatment within 360 min, and successive cycling reactions. The fusion of the extraordinary architecture of YS-CuSnO with S-Step system not only initiates the facile and practical photocatalytic exploitation, but shade light on some undeveloped side of tin oxide.

Understanding the Wettability of C1N1 (Sub)Nanopores: Implications for Porous Carbonaceous Electrodes

Understanding how water interacts with nanopores of carbonaceous electrodes is crucial for energy storage and conversion applications. A high surface area of carbonaceous materials does not necessarily need to translate to a high electrolyte-solid interface area. Herein, we study the interaction of water with nanoporous C1N1 materials to explain their very low specific capacitance in aqueous electrolytes despite their high surface area. Water was used to probe chemical environments, provided by pores of different sizes, in 1H MAS NMR experiments. We observe that regardless of their high hydrophilicity, only a negligible portion of water can enter the nanopores of C1N1, in contrast to a reference pure carbon material with a similar pore structure. The common paradigm that water easily enters hydrophilic pores does not apply to C1N1 nanopores below a few nanometers. Calorimetric and sorption experiments demonstrated strong water adsorption on the C1N1 surface, which restricts water mobility across the interface and impedes its penetration into the nanopores.

Development of Nanozymatic Characteristics in Metal-Doped Oxide Nanomaterials

Nanozymes are nanoscale materials that exhibit enzymatic-like activity, combining the benefits of nanomaterials with biocatalytic effects. The addition of metals to nanomaterials can enhance their nanozyme activity by mimicking the active sites of enzymes, providing structural support and promoting redox activity. In this study, nanostructured oxide and silicate-phosphate nanomaterials with varying manganese and copper additions were characterized. The objective was to assess the influence of metal modifications (Mn and Cu) on the acquisition of the nanozymatic activity by selected nanomaterials. An increase in manganese content in each material enhanced proteolytic activity (from 20 to 40 mUnit/mg for BG-Mn), while higher copper addition in glassy materials increased activity by 40%. Glassy materials exhibited approximately twice the 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid radical activity (around 40 μmol/mL) compared to that of oxide materials. The proteolytic and antioxidant activities discussed in the study can be considered indicators for evaluating the enzymatic properties of the nanomaterials. Observations conducted on nanomaterials may aid in the development of materials with enhanced catalytic efficiency and a wide range of applications.

Engineering the physical properties and photocatalytic activities of a β-ketoenamine COF using continuous flow synthesis

Covalent Organic Frameworks (COF) having conjugated backbone are an interesting class of metal-free, visible light active, heterogeneous photocatalysts. Interestingly, synthesis of COF using continuous flow process has emerged as an efficient, alternative method when compared to the traditional batch process. Here, we demonstrate the possibility to engineer the physical properties and hence the adsorption and catalytic activities of a β-ketoenamine COF by varying monomer flow rate and microreactor design during the continuous flow synthesis. Crystallinity of the COF increases on varying the monomer flow rate from 100 (S-100) to 500 (S-500) and up to 1000 μLmin-1 (S-1000), in an S-shaped microreactor, resulting in an enhanced surface area: 525, 722 and 1119 m2g-1 respectively. The photophysical properties of the COF are also found to vary significantly with the change in flow synthesis conditions. S-1000 is characterized by the highest adsorption of MB, due to its high surface area and accessible pores. On the other hand, S-500 shows the highest photocurrent, a low recombination of photogenerated charges and the lowest charge transfer resistance. Thus, S-500 is found to be the best photocatalyst for the removal of a model pollutant (methylene blue, MB). Further, enhanced photocatalytic removal of MB using S-500 could be achieved by performing the photocatalysis in continuous flow.

Silver nanoparticles incorporated with superior silica nanoparticles-based rice straw to maximize biogas production from anaerobic digestion of landfill leachate

Treating hazardous landfill leachate poses significant environmental challenges due to its complex nature. In this study, we propose a novel approach for enhancing the anaerobic digestion of landfill leachate using silver nanoparticles (Ag NPs) conjugated with eco-friendly green silica nanoparticles (Si NPs). The synthesized Si NPs and Ag@Si NPs were characterized using various analytical techniques, including transmission electron microscopy, X-ray diffraction, and Fourier-transform infrared spectroscopy. The anaerobic digestion performance of Si NPs and Ag@Si NPs was tested by treating landfill leachate samples with 50 mg/L of each NP. The results demonstrated an enhancement in the biogas production rate compared to the control phase without the nanocomposite, as the biogas production increased by 14% and 37% using Si NPs and Ag@Si NPs. Ag@Si NPs effectively promoted the degradation of organic pollutants in the leachate, regarding chemical oxygen demand (COD) and volatile solids (VS) by 58% and 65%. Furthermore, microbial analysis revealed that Ag@Si NPs enhanced the activity of microbial species responsible for the methanogenic process. Overall, incorporating AgNPs conjugated with eco-friendly green Si NPs represents a sustainable and efficient approach for enhancing the anaerobic digestion of landfill leachate.

The synergistic interplay of hierarchy, crystal size, and Ga-promotion in the methanol-to-aromatics process over ZSM-5 zeolites

In the context of advancing social modernization, the projected shortfall in the demand for renewable aromatic hydrocarbons is expected to widen, influenced by industries like high-end materials, pharmaceuticals, and consumer goods. Sustainable methods for aromatic production from alternative sources, particularly the methanol-to-aromatics (MTA) process using zeolite ZSM-5 and associated with the "methanol economy", have garnered widespread attention. To facilitate this transition, our project consolidates conventional strategies that impact aromatics selectivity-such as using hierarchical zeolites, metallic promoters, or altering zeolite physicochemical properties-into a unified study. Our findings demonstrate the beneficial impact of elongated crystal size and heightened zeolite hierarchy on preferential aromatics selectivity, albeit through distinct mechanisms involving the consumption of shorter olefins. While metallic promoters enhance MTA performance, crystal size, and hierarchy remain pivotal in achieving the maximized aromatics selectivity. This study contributes to a deeper understanding of achieving superior aromatics selectivity through physicochemical modifications in zeolite ZSM-5 during MTA catalysis, thereby advancing the field's comprehension of structure-reactivity relationships.

Sorption Hysteresis: A Statistical Thermodynamic Fluctuation Theory

Hysteresis is observed commonly in sorption isotherms of porous materials. Still, there has so far been no unified approach that can both model hysteresis and assess its underlying energetics. Standard approaches, such as capillary condensation and isotherms based on interfacial equations of state, have not proved to be up to the task. Here, we show that a statistical thermodynamic approach can achieve the following needs simultaneously: (i) showing why adsorption and desorption transitions may be sharp yet continuous; (ii) providing a simple (analytic) isotherm equation for hysteresis branches; (iii) clarifying the energetics underlying sorption hysteresis; and (iv) providing macroscopic and nanoscopic perspectives to understanding hysteresis. This approach identifies the two pairs of parameters (determinable by fitting experimental data) that are required to describe the hysteresis: the free energy per molecule within the pore clusters and the cluster size in the pores. The present paper focuses on providing mechanistic insights to IUPAC hysteresis types H1, H2(a), and H2(b) and can also be applied to the isotherm types IV and V.

Mullite-like SmMn2O5-Derived Composite Oxide-Supported Ni-Based Catalysts for Hydrogen Production by Auto-Thermal Reforming of Acetic Acid

The x%Ni/Sm2O3-MnO (x = 0, 10, 15, 20) catalysts derived from SmMn2O5 mullite were prepared by solution combustion and impregnation method; auto-thermal reforming (ATR) of acetic acid (HAc) for hydrogen production was used to explore the metal-support effect induced by Ni loadings on the catalytic reforming activity and product distribution. The 15%Ni/Sm2O3-MnO catalyst exhibited optimal catalytic performance, which can be due to the appropriate Ni loading inducing a strong metal-support interaction to form a stable Ni/Sm2O3-MnO active center, while side reactions, such as methanation and ketonization, were well suppressed. According to characterizations, Sm2O3-MnO mixed oxides derived from SmMn2O5 mullite were formed with oxygen vacancies; nevertheless, loading of Ni metal further promoted the formation of oxygen vacancies, thus enhancing adsorption and activation of oxygen-containing intermediate species and resulting in higher reactivity with HAc conversion near 100% and hydrogen yield at 2.62 mol-H2/mol-HAc.

Mechanical properties, sustained release, and oxygen scavenging properties of nanocomposite films loaded with bimetallic nanoparticles (Fe2O3/TiO2) in extra virgin olive oil

The aim of this study was the synthesis of bimetallic nanoparticles based on Fe2O3/TiO2 and its use in the poly(lactic acid) (PLA) films as an oxygen scavenger in extra virgin olive oil (EVOO) packaging. Bimetallic nanocomposites were prepared by two different precipitation methods (precipitation with ammonia and sodium hydroxide). The characteristics of bimetallic nanoparticles precipitated with sodium hydroxide (Na-Ti0.01Fe0.048O0.08) and bimetallic nanoparticles precipitated with ammonia (NH-Ti0.01Fe0.022O0.09) were compared. Relative amounts of elements in bimetallic nanocomposites and their morphological characteristics were determined using field emission scanning electron microscopy coupled with energy-dispersive X-ray spectrometer. Porosity volume and surface area of bimetallic nanoparticles were calculated using adsorption-desorption isotherms and the Brunauer-Emmett-Teller method. The formation/characterization of bimetallic nanoparticles and their location in the matrix of PLA-based nanocomposite film was studied using X-ray diffraction and Fourier transform infrared. In nanocomposite films based on PLA, bimetallic nanoparticles lead to better oxidative stability (peroxide value, p-anisidine index, K232, and K270) of the EVOO and oxygen scavenging during storage compared to free nanoparticles. Mechanical properties of nanocomposite films were improved due to bimetallic nanoparticles, which were better for Na-Ti0.01Fe0.048O0.08. In vitro release modeling of the bimetallic nanoparticles in EVOO proved that Fickian diffusion is the dominant mechanism, and the Peleg model was the best description of the release behavior of nanoparticles.

Beyond Conventional Carbon Activation: Creating Porosity without Etching Using Cesium Effect

Facile synthesis of porous carbon with high yield and high specific surface area (SSA) from low-cost molecular precursors offers promising opportunities for their industrial applications. However, conventional activation methods using potassium and sodium hydroxides or carbonates suffer from low yields (<20%) and poor control over porosity and composition especially when high SSAs are targeted (>2000 m2 g-1) because nanopores are typically created by etching. Herein, a non-etching activation strategy is demonstrated using cesium salts of low-cost carboxylic acids as the sole precursor in producing porous carbons with yields of up to 25% and SSAs reaching 3008 m2 g-1. The pore size and oxygen content can be adjusted by tuning the synthesis temperature or changing the molecular precursor. Mechanistic investigation unravels the non-classical role of cesium as an activating agent. The cesium compounds that form in situ, including carbonates, oxides, and metallic cesium, have extremely low work function enabling electron injection into organic/carbonaceous framework, promoting condensation, and intercalation of cesium ions into graphitic stacks forming slit pores. The resulting porous carbons deliver a high capacity of 252 mAh g-1 (567 F g-1) and durability of 100 000 cycles as cathodes of Zn-ion capacitors, showing their potential for electrochemical energy storage.

Low-Hydrophilic HKUST-1/Polymer Extrudates for the PSA Separation of CO2/CH4

HKUST-1 is an MOF adsorbent industrially produced in powder form and thus requires a post-shaping process for use as an adsorbent in fixed-bed separation processes. HKUST-1 is also sensitive to moisture, which degrades its crystalline structure. In this work, HKUST-1, in the form of crystalline powder, was extruded into pellets using a hydrophobic polymeric binder to improve its moisture stability. Thermoplastic polyurethane (TPU) was used for that purpose. The subsequent HKUST-1/TPU extrudate was then compared to HKUST-1/PLA extrudates synthesized with more hydrophilic polymer: polylactic acid (PLA), as the binder. The characterization of the composites was determined via XRD, TGA, SEM-EDS, and an N2 adsorption isotherm analysis. Meanwhile, the gas-separation performances of HKUST-1/TPU were investigated and compared with HKUST-1/PLA from measurements of CO2 and CH4 isotherms at three different temperatures, up to 10 bars. Lastly, the moisture stability of the composite materials was investigated via an aging analysis during storage under humid conditions. It is shown that HKUST-1's crystalline structure was preserved in the HKUST-1/TPU extrudates. The composites also exhibited good thermal stability under 523 K, whilst their textural properties were not significantly modified compared with the pristine HKUST-1. Furthermore, both extrudates exhibited larger CO2 and CH4 adsorption capacities in comparison to the pristine HKUST-1. After three months of storage under atmospheric humid conditions, CO2 adsorption capacities were reduced to only 10% for HKUST-1/TPU, whereas reductions of about 25% and 54% were observed for HKUST-1/PLA and the pristine HKUST-1, respectively. This study demonstrates the interest in shaping MOF powders by extrusion using a hydrophobic thermoplastic binder to operate adsorbents with enhanced moisture stability in gas-separation columns.

Unraveling the role of internal-external metal substitution in Zn3[Co(CN6)]2 for the styrene oxide-CO2 cycloaddition reaction

We investigated the influence of the structural and textural properties along with the chemical environment of pure Zn3[Co(CN)6]2 in comparison with the modified phases on the catalytic performance in the cycloaddition reaction between styrene oxide and CO2. We relate these to the proposed reaction pathways and mechanisms. The natural cubic phase (ZnCoCn) was dehydrated to obtain the rhombohedral phase (ZnCoRn), while the stabilized cubic phase (ZnCoCs) was synthesized by substituting external zinc atoms with cadmium atoms. The rhombohedral stabilized phase (ZnCoRs) was achieved by the internal cobalt change with iron. All the materials were extensively characterized using X-ray diffraction (XRD), thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), X-ray photoelectron spectroscopy (XPS), and N2 adsorption. The catalytic behavior of the four phases was tested. The crystalline structure of each phase was obtained, and by XPS, it was demonstrated that the chemical environments of all elements conforming to the rhombohedral stabilized phase are different from those of all other materials owing to the exchange of internal metals. The bulk textural properties were similar; only the ZnCoRs presented more micropore area but did not exceed the total surface area of the other materials. The product distribution and yield at reaction times of 2 h and 6 h were closer to those of the cubic phases. The natural rhombohedral phase exhibits the best performance. The tetrabutylammonium bromide (TBAB) and rhombohedral stabilized phase work together to yield a bigger copolymer quantity at the expense of the styrene carbonate (StCO3) production. From the proposed mechanism, the TBAB cation (TBA+) has a "protection" function that drives the closing of the StCO3 ring; however, the charge distribution anisotropy in the four nitrogen atoms generated by Co replacement in ZnCoRs could hold TBA+ as the reaction time progressed, causing an unavailability that triggered the copolymerization propagation step.

Spherical Binderless 4A/5A Zeolite Assemblies: Synthesis, Characterization, and Adsorbent Applications

Zeolite microspheres have been successfully applied in commercial-scale separators such as oxygen concentrators. However, further enhancement of their applications is hampered by the post-synthetic shaping process that formulates the zeolite powder into packing-sized spherical bodies with various binders leading to active site blockage and suboptimal performance. Herein, binderless zeolite microspheres with a tunable broad size range from 2 µm to 500 µm have been developed with high crystallinity, sphericity over 92%, monodispersity with a coefficient of variation (CV) less than 5%, and hierarchical pore architecture. Combining precursor impregnation and steam-assisted crystallization (SAC), mesoporous silica microspheres with a wide size range could be successfully transformed into zeolite. For preserved size and spherical morphology, a judicious selection of the synthesis conditions is crucial to ensure a pure phase, high crystallinity, and hierarchical architecture. For the sub-2-µm zeolite microsphere, low-temperature prolonged aging was important so as to suppress external zeolization that led to a large, single macroporous crystal. For the large 500 µm sphere, ultrasound pretreatment and vacuum impregnation were crucial and facilitated spatially uniform gel matrix dispersion and homogenous crystallization. The obtained zeolite 5A microspheres exhibited excellent air separation performance, while the 4A microspheres displayed ammonium removal capabilities. This work provides a general strategy to overcome the existing limitations in fabricating binder-free technical bodies of zeolites for various applications.

Block copolymer self-assembly derived mesoporous magnetic materials with three-dimensionally (3D) co-continuous gyroid nanostructure

Magnetic nanomaterials are gaining interest for their many applications in technological areas from information science and computing to next-generation quantum energy materials. While magnetic materials have historically been nanostructured through techniques such as lithography and molecular beam epitaxy, there has recently been growing interest in using soft matter self-assembly. In this work, a triblock terpolymer, poly(isoprene-block-styrene-block-ethylene oxide) (ISO), is used as a structure directing agent for aluminosilicate sol nanoparticles and magnetic material precursors to generate organic-inorganic bulk hybrid films with co-continuous morphology. After thermal processing into mesoporous materials, results from a combination of small angle X-ray scattering (SAXS) and scanning electron microscopy (SEM) are consistent with the double gyroid morphology. Nitrogen sorption measurements reveal a type IV isotherm with H1 hysteresis, and yield a specific surface area of around 200 m2 g-1 and an average pore size of 23 nm. The magnetization of the mesostructured material as a function of applied field shows magnetic hysteresis and coercivity at 300 K and 10 K. Comparison of magnetic measurements between the mesoporous gyroid and an unstructured bulk magnetic material, derived from the identical inorganic precursors, reveals the structured material exhibits a coercivity of 250 Oe, opposed to 148 Oe for the unstructured at 10 K, and presence of remnant magnetic moment not conventionally found in bulk hematite; both of these properties are attributed to the mesostructure. This scalable route to mesoporous magnetic materials with co-continuous morphologies from block copolymer self-assembly may provide a pathway to advanced magnetic nanomaterials with a range of potential applications.

Surface Reconstruction Facilitated by Fluorine Migration and Bimetallic Center in NiCo Bimetallic Fluoride Toward Oxygen Evolution Reaction

Oxygen evolution reaction (OER) is a critical anodic reaction of electrochemical water splitting, developing a high-efficiency electrocatalyst is essential. Transition metal-based catalysts are much more cost-effective if comparable activities can be achieved. Among them, fluorides are rarely reported due to their low aqueous stability of coordination and low electric conductivity. Herein, a NiCo bimetallic fluoride with good crystallinity is designed and constructed, and significantly enhanced catalytic activity and conductivity are observed. The inevitable oxidation of transition metal ions at high potential and the dissociation of F- are attributed to the low aqueous stability of coordination. The theoretical researches predicte that transition metal fluorides should have a strong tendency to electrochemical reconstruction. Therefore, based on the observations on their electrochemical behavior, high-resolution transmission electron microscopy, X-ray photoelectron spectroscopy, and bode plots, it is further demonstrated that surface reconstruction occurred during the electrochemical process, meanwhile a significant increase of electrochemically active area, which is created by F migration, are also directly observed. Additionally, DFT calculation results show that the electronic structure of the catalysts is modulated by the bimetallic centers, and this reconstruction helps optimizing the adsorption energy of oxygen-containing species and improves OER activity.

Aspects of Gas Storage: Confined Geometry Effects on the High-Pressure Adsorption Behavior of Supercritical Fluids

During the last decades, major progress was made concerning the understanding of subcritical low-pressure adsorption of fluids like nitrogen and argon at their boiling temperatures in nanoporous materials. It was possible to understand how structural properties affect the shape of the adsorption isotherms. However, within the context of gas storage applications, supercritical high-pressure gas adsorption is important. A key feature here is that the experimentally determined surface excess adsorption isotherm may exhibit a characteristic maximum at a certain pressure. For a given temperature and adsorptive/adsorbent system, the surface excess maximum (and the corresponding adsorbed amount) is related to the storage capacity of the adsorbent. However, there is still a lack of understanding of how key textural properties such as surface area and pore size affect details of the shape of supercritical high-pressure adsorption isotherms. To address these open questions, we have performed a systematic experimental study assessing the effect of pore size/structure on the supercritical adsorption isotherms of pure fluids such as C2H4, CO2, and SF6 over a wider range of temperatures and pressures on a series of model materials exhibiting well-defined pore sizes, i.e., ordered micro- and mesoporous materials (e.g., NaY zeolite, KIT-6 silica, and MCM-48 silica). A fundamental result of our experiments is a unique fluid-independent correlation between the pressure of the surface excess maximum pmax (at a given temperature) and the pore size (by taking into account the kinetic diameter of the fluid and the underlying effective attractive fluid-wall interaction). Summarizing, our results suggest important structure-property relationships, allowing one to determine, for given thermodynamic conditions, important information related to the optimal operating conditions for supercritical adsorption applications. The insights may also serve as a basis for optimizing and tailoring the properties of nanoporous adsorbent materials for gas storage applications.

Effects of the adsorbate-gas interface at the pore opening on the lower closure point in gaseous adsorption in porous solids

The limit to the lower closure point (LCP) observed experimentally in the desorption isotherm of gases in porous solids has been commonly attributed to the homogeneous cavitation of the condensate in cavities. It was proposed recently that the experimental limit to LCP could be described in simulations with the ink-bottle pore, provided that the length of the uniformly sized conduit connecting the closed cavity to the surrounding is shorter than 2 nm, and the evaporation is by way of pore blocking mechanism, rather than homogeneous cavitation. To substantiate this assertion, that deviates from the commonly belief of homogeneous cavitation, we further investigated in this paper with cavities having wedge-like pore opening, that better mimics real solids, and offer further explanation on the limit of the LCP to the pore blocking as the mechanism of evaporation with simulations of argon and nitrogen adsorption over a range of temperatures that are commonly used experimentally. It was found that simulation results correctly captured the experimental observations for carbon-based materials and silica-based materials in that the limit of LCP shifts to higher reduced pressures for weaker adsorbing silica, compared to stronger adsorbing carbon and for a given adsorbent it also shifts to higher reduced pressure for higher temperatures.

Overcoming the permeability-selectivity challenge in water purification using two-dimensional cobalt-functionalized vermiculite membrane

Clean water and sanitation are major global challenges highlighted by the UN Sustainable Development Goals. Water treatment using energy-efficient membrane technologies is one of the most promising solutions. Despite decades of research, the membrane permeability-selectivity trade-off remains the major challenge for synthetic membranes. To overcome this challenge, here we develop a two-dimensional cobalt-functionalized vermiculite membrane (Co@VMT), which innovatively combines the properties of membrane filtration and nanoconfinement catalysis. The Co@VMT membrane demonstrates a high water permeance of 122.4 L·m-2·h-1·bar-1, which is two orders of magnitude higher than that of the VMT membrane (1.1 L·m-2·h-1·bar-1). Moreover, the Co@VMT membrane is applied as a nanofluidic advanced oxidation process platform to activate peroxymonosulfate (PMS) for degradation of several organic pollutants (dyes, pharmaceuticals, and phenols) and shows excellent degradation performance (~100%) and stability (for over 107 h) even in real-world water matrices. Importantly, safe and non-toxic effluent water quality is ensured by the Co@VMT membrane/PMS system without brine, which is totally different from the molecular sieving-based VMT membrane with the concentrated pollutants remaining in the brine. This work can serve as a generic design blueprint for the development of diverse nanofluidic catalytic membranes to overcome the persistent membrane permeability-selectivity issue in water purification.

Insights into effects of grain boundary engineering in composite metal oxide catalysts for improving catalytic performance

Volatile Organic Compounds (VOCs) have long been a threat to human health. However, designing economical and efficient transition metal composite oxide catalysts for VOCs purification remains a challenge. Herein, this study demonstrates the enormous potential of grain boundary engineering in facilitating VOCs decomposition over ordered mesoporous composite oxide denoted as 3D-MnxCoy (x, y = 1, 3, 5, 7, 9). Specifically, the three-dimensional (3D) Mn7Co1 catalyst shows 100% ethyl acetate removal efficiency for a continuous airflow containing 1000 ppm ethyl acetate over 60000 h-1 space velocity at 160 °C. Mechanism study suggests that the high catalytic performance originates from the lattice distortion caused by the introduction of heteroatoms, along with the size effect of nanopore walls, which leads to the formation of various grain boundaries on the catalyst surface. The presence of grain boundaries facilitates the generation of oxygen vacancies, thus promoting the migration and activation of oxygen species. Furthermore, the near-atmospheric pressure X-ray photoelectron spectroscopy (NAP- XPS) monitoring results reveal that the bimetallic synergy enhanced by grain boundary accelerates the catalytic reaction rate of VOCs through Mn3++Co3+↔Mn4++Co2+ redox cycle. This study may shed light on the great potential of ordered mesoporous bimetallic oxide catalysts in VOCs pollution control.

Discovery and In Situ Crystallization Studies of Cerium-Based Metal-Organic Frameworks with V-Shaped Linker Molecules

We report the discovery and characterization of two porous Ce(III)-based metal-organic frameworks (MOFs) with the V-shaped linker molecules 4,4'-sulfonyldibenzoate (SDB2-) and 4,4'-(hexafluoroisopropylidene)bis(benzoate) (hfipbb2-). The compounds of framework composition [Ce2(H2O)(SDB)3] (1) and [Ce2(hfipbb)3] (2) were obtained by using a synthetic approach in acetonitrile that we recently established. Structure determination of 1 was accomplished from 3D electron diffraction (3D ED) data, while 2 could be refined against powder X-ray diffraction (PXRD) data using the crystal structure of an isostructural La-MOF as the starting model. Their framework structures consist of chain-like inorganic building units (IBUs) or hybrid-BUs that are interconnected by the V-shaped linker molecules to form framework structures with channel-type pores. The composition of both compounds was confirmed by PXRD, elemental analysis, as well as NMR and IR spectroscopy. Interestingly, despite the use of (NH4)2[CeIV(NO3)6] in the synthesis, cerium ions in both MOFs occur exclusively in the + III oxidation state as determined by X-ray absorption near edge structure (XANES) and X-ray photoelectron spectroscopy (XPS). Thermal analyses reveal remarkably high thermal stabilities of ≥400 °C for the MOFs. Initial N2 sorption measurements revealed the peculiar sorption behavior of 2 which prompted a deeper investigation by Ar and CO2 sorption experiments. The combination with nonlocal density functional theory (NL-DFT) calculations adds to the understanding of the nature of the different pore diameters in 2. An extensive quasi-simultaneous in situ XANES/XRD investigation was carried out to unveil the formation of Ce-MOFs during the solvothermal syntheses in acetonitrile. The crystallization of the two Ce(III)-MOFs presented herein as well as two previously reported Ce(IV)-MOFs, all obtained by a similar synthetic approach, were studied. While the XRD patterns show time-dependent MOF crystallization, the XANES data reveal the presence of Ce(III) intermediates and their subsequent conversion to the MOFs. The addition of acetic acid in combination with the V-shaped linker molecule was identified as the crucial factor for the formation of the crystalline Ce(III/IV)-MOFs.

Unraveling the Structural and Compositional Peculiarities in CTAB-Templated CeO2-ZrO2-MnOx Catalysts for Soot and CO Oxidation

Structure-performance relationships in functional catalysts allow for controlling their performance in a wide range of reaction conditions. Here, the structural and compositional peculiarities in CTAB-templated CeO2-ZrO2-MnOx catalysts prepared by co-precipitation of precursors and their catalytic behavior in CO oxidation and soot combustion are discussed. A complex of physical-chemical methods (low-temperature N2 sorption, XRD, TPR-H2, Raman, HR TEM, XPS) is used to elucidate the features of the formation of interphase boundaries, joint phases, and defects in multicomponent oxide systems. The addition of Mn and/or Zr dopant to ceria is shown to improve its performance in both reactions. Binary Ce-Mn catalysts demonstrate enhanced performance closely followed by the ternary oxide catalysts, which is due the formation of several types of active sites, namely, highly dispersed MnOx species, oxide-oxide interfaces, and oxygen vacancies that can act individually and/or synergistically.

Mixture Adsorption in Nanoporous Zeolite and at Its External Surface: In-Pore and Surface Selectivity

Using toluene, ethylene, and water as gas compounds with different representative molecular interactions, we perform atom-scale simulations for their mixtures to investigate the selectivity of the core nanoporosity and external surface in a prototypical zeolite. As expected, the overall behavior suggests that increasing the pressure of a given component promotes the desorption of the coadsorbing species. However, for water-toluene mixtures, we identify that the pseudohydrogen bonding between water and toluene leads to beneficial coadsorption as toluene adsorption in the low-pressure range promotes water adsorption. Moreover, when the zeolite is completely filled with water, toluene adsorption does not occur due to steric repulsion, and ethylene shows oversolubility as the amount of ethylene per water molecule is significantly larger than in bulk water. The underlying oversolubility mechanism is found to be due to localized ethylene adsorption in the density minima arising from the layering of water in nanoconfinement. Despite these specific effects, the relatively weak coadsorption effects in the zeolite nanoporosity, which are found to be reasonably captured using the ideal adsorbed solution theory, arise from the fact that adsorption of these gases having different molecular sizes occurs in distinct pore regions (channel type, channel intersection). Finally, in contrast to confinement in the nanoporosity, mixture adsorption at the external surface does not show coadsorption effects as it mostly follows the Henry regime. These results show that selectivity is mostly governed by the confinement effects as the external surface leads to a selectivity loss.

Hydrodeoxygenation of Oxygenates Derived from Biomass Pyrolysis Using Titanium Dioxide-Supported Cobalt Catalysts

Bio-oil upgrading to produce biofuels and chemicals has become an attractive topic over the past decade. However, the design of cost- and performance-effective catalysts for commercial-scale production remains a challenge. Herein, commercial titania (TiO2) was used as the support of cobalt (Co)-based catalysts (Co/TiO2) due to its low cost, high availability, and practicability for commercialization in the future. The Co/TiO2 catalysts were made with two different forms of TiO2 (anatase [TiO2-A] and rutile [TiO2-R]) and comparatively evaluated in the hydrodeoxygenation (HDO) of 4-propylguaicol (4PG), a lignin-derived model compound. Both Co/TiO2 catalysts promoted the HDO of 4PG following a similar pathway, but the Co/TiO2-R catalyst exhibited a higher activity in the early stages of the reaction due to the formation of abundant Ti3+ species, as detected by X-ray photoelectron spectroscopy (XPS) and hydrogen-temperature programed reduction (H2-TPR) analyses. On the other hand, the Co/TiO2-A catalyst possessed a higher acidity that enhanced propylcyclohexane production at prolonged reaction times. In terms of reusability, the Co/TiO2-A catalyst showed a higher stability (less Co leaching) and reusability compared to Co/TiO2-R, as confirmed by transmission electron microscopy (TEM) and inductively coupled plasma optical emission spectroscopy (ICP-OES) analyses. The HDO of the real bio-oil derived from pyrolysis of Leucaena leucocephala revealed that the Co/TiO2-A catalyst could convert high oxygenated aromatics (methoxyphenols, dimethoxyphenols, and benzenediols) to phenols and enhanced the phenols content, hinting at its potential to produce green chemicals from bio-feedstock.

Surface diffusion enhanced ion transport through two-dimensional nanochannels

Fast ion permeation in nanofluidic channels has been intensively investigated in the past few decades because of their potential uses in separation technologies and osmotic energy harvesting. Mechanisms governing ion transport at this ultimately small spatial regime remain to be understood, which can only be achieved in nanochannels that are controllably fabricated. Here, we report the fabrication of two-dimensional nanochannels with their top and bottom walls consisting of atomically flat graphite and mica crystals, respectively. The distinct wall structures and properties enable us to investigate interactions between ions and interior surfaces. We find an enhanced ion transport within the channels that is orders of magnitude faster than that in the bulk solutions. The result is attributed to the highly dense packing of adsorbed cations at mica surfaces, where they diffuse in-plane. Our work provides insights into surface effects on ion transport at the nanoscale.

Nanoconfined Water in Pillared Zeolites Probed by 1H Nuclear Magnetic Resonance

Here, we report the results of our 1H nuclear magnetic resonance study of the dynamics of water molecules confined in zeolites (mordenite and ZSM-5 structures) with hierarchical porosity (micropores in zeolite lamella and mesopores formed by amorphous SiO2 in the inter-lamellar space). 1H nuclear magnetic resonance (NMR) spectra show that water experiences complex behavior within the temperature range from 173 to 298 K. The temperature dependence of 1H spin-lattice relaxation evidences the presence of three processes with different activation energies: freezing (about 30 kJ/mol), fast rotation (about 10 kJ/mol), and translational motion of water molecules (23.6 and 26.0 kJ/mol for pillared mordenite and ZSM-5, respectively). For translational motion, the activation energy is markedly lower than for water in mesoporous silica or zeolites with similar mesopore size but with disordered secondary porosity. This indicates that the process of water diffusion in zeolites with hierarchical porosity is governed not only by the presence of mesopores, but also by the mutual arrangement of meso- and micropores. The translational motion of water molecules is determined mainly by zeolite micropores.

Magnetic Fe3O4/bamboo-based activated carbon/UiO-66 composite as an environmentally friendly and effective adsorbent for removal of Bisphenol A

The magnetic Fe3O4/bamboo-based activated carbon/Zr-based metal-organic frameworks composite (Fe3O4/BAC/UiO-66) was prepared by hydrothermal method. The as-prepared material was analyzed via TEM, XRD, FT-IR, BET-BJH, VSM and XPS techniques, the results showed that it had good dispersion and magnetic separation capacity (Ms = 44.06 emu∙g-1). Then, the adsorption properties of materials for bisphenol A (BPA) were studied. The results revealed that the removal efficiency of 50 mg·L-1 BPA by 0.1 g of adsorbent can reach 87.18-95% in a wide pH range. Langmuir isotherm model and pseudo-second-order kinetic well fitted the adsorption data. The thermodynamic data indicated that the adsorption process was spontaneous and endothermic. Moreover, BAC as a supporter and UiO-66 as the functional part in the ternary composite may have a synergistic effect, which was beneficial for the removal of contaminants. The Fe3O4/BAC/UiO-66 can be simply separated from the water using its strong magnetism after finish adsorption process, which effectively avoids secondary contamination.

3D Monolayer Silanation of Porous Structure Facilitating Multi-Phase Pollutants Removal

Activated carbon (AC) is widely used to removing hazardous pollutants from air and water, owing to its exceptional adsorption properties. However, the high affinity of water molecules with the surface oxygen-containing functional groups can adversely affect the adsorption performance of AC. In this study, a facile and efficient method is presented for fabrication of hydrophobic AC through surface monolayer silanation. Compared to initial AC, the hydrophobic AC improves the water contact angle from 29.7° to 123.5° while maintaining high specific surface area and enhances the removal capacity of multi-phase pollutants (emulsified oil and toluene). Additionally, the hydrophobic AC exhibits excellent adsorption capability to harmful algal bloom species (Chlorella) (97.56%) and algal organic matter (AOM) (96.23%) owing to electrostatic interactions and surface hydrophobicity. The study demonstrates that this method of surface monolayer silanation can effectively weaken the effect of water molecules on AC adsorption capacity, which has significant potential for practical use in air and water purification, as well as in the control of harmful algal blooms.

Evaluating the efficacy of zeolites synthesized from natural clay for the methanol-to-hydrocarbon process

Introducing sustainability into advanced catalytic material design is essential to address growing environmental concerns. Among them, synthesizing inorganic zeolite materials from non-traditional sources (like natural clay) offers several advantages, contributing to sustainability and environmental stewardship. With this objective, we used kaolin to synthesize zeolites with different topologies: SSZ-13 (8-MR with CHA topology), ZSM-5 (10-MR with MFI topology), and Beta (12-MR with BEA topology) (MR: member ring), where a simple and flexible synthetic protocol was adopted without any significant changes. All these zeolites were subjected to catalytic performance evaluation concerning the industrially relevant methanol-to-hydrocarbon (MTH) process. Herein, the kaolin-derived zeolites, especially ZSM-5, led to superior performance and demonstrated enhanced catalyst deactivation-resistant behavior compared to their zeolite counterparts prepared from traditional synthetic routes. Various characterization tools (including under operando conditions) were employed to understand their reactions and deactivation mechanisms. Overall, making zeolites from non-traditional sources presents a pathway for sustainable and environmentally friendly material production, offering benefits such as reduced resource dependence, lower energy consumption, and tailored physicochemical properties beneficial to catalysis. In a broader context, such a research approach contributes to the transition toward a more sustainable and circular economy.

Synthetic Control of the Defect Structure and Hierarchical Extra-Large-/Small-Pore Microporosity in Aluminosilicate Zeolite SWY

The SWY-type aluminosilicate zeolite, STA-30, has been synthesized via different routes to understand its defect chemistry and solid acidity. The synthetic parameters varied were the gel aging, the Al source, and the organic structure directing agent. All syntheses give crystalline materials with similar Si/Al ratios (6-7) that are stable in the activated K,H-form and closely similar by powder X-ray diffraction. However, they exhibit major differences in the crystal morphology and in their intracrystalline porosity and silanol concentrations. The diDABCO-C82+ (1,1'-(octane-1,8-diyl)bis(1,4-diazabicyclo[2.2.2]octan)-1-ium)-templated STA-30 samples (but not those templated by bisquinuclidinium octane, diQuin-C82+) possess hierarchical microporosity, consisting of noncrystallographic extra-large micropores (13 Å) that connect with the characteristic swy and gme cages of the SWY structure. This results in pore volumes up to 30% greater than those measured in activated diQuin-C8_STA-30 as well as higher concentrations of silanols and fewer Brønsted acid sites (BASs). The hierarchical porosity is demonstrated by isopentane adsorption and the FTIR of adsorbed pyridine, which shows that up to 77% of the BASs are accessible (remarkable for a zeolite that has a small-pore crystal structure). A structural model of single can/d6r column vacancies is proposed for the extra-large micropores, which is revealed unambiguously by high-resolution scanning transmission electron microscopy. STA-30 can therefore be prepared as a hierarchically porous zeolite via direct synthesis. The additional noncrystallographic porosity and, subsequently, the amount of SiOHs in the zeolites can be enhanced or strongly reduced by the choice of crystallization conditions.

Highly Efficient Conversion of Greenhouse Gases Using a Quadruple Mixed Oxide-Supported Nickel Catalyst in Reforming Process

The greenhouse gas reduction as well as the utilization of more renewable and clean energy via a dry reforming reaction is of interest. The impact of a CeMgZnAl oxide quad-blend-supported Ni catalyst on performance and anticoking during dry reforming reactions at 700 °C was studied. A high Ce-Mg/Zn ratio, as seen in the CeMg0.5ZnAl-supported nickel catalyst, enhances lattice oxygen, and the presence of strong basic sites, along with the creation of the carbonate intermediate species, is accompanied by the production of gaseous CO through a gasification reaction between the carbon species and Ni-COads-lin site. The phenomena caused the outstanding performance of the Ni/CeMg0.5ZnAl catalyst-CH4 (84%),CO2 (83%) conversions, and the H2/CO (0.80) ratio; moreover, its activity was also stable throughout 30 h.

Interplay Between Particle Size and Hierarchy of Zeolite ZSM-5 During the CO2 -to-aromatics Process

The CO2 -to-aromatics process is a chemical reaction that converts carbon dioxide (CO2 ) into valuable petrochemical, i. e., aromatics (especially, benzene, toluene, and xylene) over the metal/zeolite bifunctional catalytic systems. These aromatics are used in producing plastics, fibers, and other industrial products, which are currently exclusively sourced from fossil-derived feedstocks. The significance of this process lies in its potential to mitigate climate change by reducing greenhouse gas emissions and simultaneously producing valuable chemicals. Consequently, these CO2 -derived aromatics can reduce the reliance on fossil fuels as a source of feedstocks, which can help to promote a more sustainable and circular economy. Owing to the existence of a wider straight channel favoring the aromatization process, zeolite ZSM-5 is extensively used to yield aromatics during CO2 hydrogenation over bifunctional (metal/zeolite) catalytic systems. To provide a better understanding of this unique property of zeolite ZSM-5, this work investigates the impact of particle size and hierarchy of the zeolite and how these govern the reaction performance and the overall selectivity. As a result, an improved understanding of the zeolite-catalyzed hydrocarbon conversion process has been obtained.

Determination of the surface properties and adsorption states of nanoporous materials using the zeta adsorption isotherm

The adsorption process of porous materials has always been a popular field of research in interfacial physics, and the surface physical parameters of materials can be obtained from their adsorption characteristics, which has a great influence on the performance of materials. Based on the zeta adsorption isotherm, we propose a method based on the zeta adsorption isotherm to predict the entire adsorption process of porous materials and determine material surface properties from the measured isotherm data in the heterogeneity-free range. We applied the zeta constants of the silica adsorption system to the corresponding adsorption isotherm of the porous material. The results showed that the predicted adsorption isotherms are in good agreement with the experimental measurements before pore filling and can effectively identify the pressure ratios at the beginning and end of pore filling. In the region of high-pressure ratios, the Kelvin equation was utilized to calculate the pressure ratio at a contact angle of 0°. The surface parameters of the materials were determined by geometrically calculating the variation of the adsorption amount and the desorption isotherms in the high-pressure ratio range were calculated from these surface parameters. The predicted desorption isotherms can well reflect the adsorption process of silica porous materials in the region of a high-pressure ratio. In addition, for the surface parameters of the materials, the specific surface area calculated from the adsorption and desorption isotherms, respectively, differed by less than 7.9%, and the reliability of the method was verified by comparing the results with those of the argon adsorption systems.

Hierarchical Zeolites Containing Vanadium or Tantalum and Their Application in Cyclohexene Epoxidation Reaction

The aim of this study was the synthesis, characterization, and catalytic application of new hierarchical materials modified with tantalum and vanadium ions. These materials exhibit secondary porosity, thus allowing the reactant molecules to access the active sites of the material while maintaining the acidity and crystallinity of the zeolites. Based on the results, these systems were found to be highly active and selective in the oxidation of cyclohexene. The performance of the catalysts was compared in oxidation processes carried out by conventional and microwave-assisted methods. Microwave-assisted experiments showed that in the presence of a hierarchical FAU zeolite containing Ta, long reaction times could be shortened with increased activity and selectivity under the same residual experimental conditions.

The influence of sample mass (scaling effect) on the synthesis and structure of non-graphitizing carbon (biochar) during the analytical pyrolysis of biomass

The porous non-graphitizing carbon (NGC) known as biochar is derived from the pyrolytic conversion of organic precursors and is widely investigated due to its multifunctional applications. At present, biochar is predominantly synthesized in custom lab-scale reactors (LSRs) to determine the properties of carbon, while a thermogravimetric reactor (TG) is utilized for pyrolysis characterization. This results in inconsistencies in the correlation between the structure of biochar carbon and the pyrolysis process. If a TG reactor can also be used as an LSR for biochar synthesis, then the process characteristics and the properties of the synthesized NGC can be simultaneously investigated. It also eliminates the need for expensive LSRs in the laboratory, improves the reproducibility, and correlatability of pyrolysis characteristics with the properties of the resulting biochar carbon. Furthermore, despite numerous TG studies on the kinetics and characterization of biomass pyrolysis, none have questioned how the properties of biochar carbon vary due to the influence of the starting sample mass (scaling) in the reactor. Herein, with a lignin-rich model substrate (walnut shells), TG is utilized as an LSR, for the first time, to investigate the scaling effect starting from the pure kinetic regime (KR). The changes in the pyrolysis characteristics and the structural properties of the resultant NGC with scaling are concurrently traced and comprehensively studied. It is conclusively proven that scaling influences the pyrolysis process and the NGC structure. There is a gradual shift in pyrolysis characteristics and NGC properties from the KR until an inflection mass of ∼200 mg is reached. After this, the carbon properties (aryl-C%, pore characteristics, defects in nanostructure, and biochar yield) are similar. At small scales (≲100 mg), and especially near the KR (≤10 mg) carbonization is higher despite the reduced char formation reaction. The pyrolysis is more endothermic near KR with increased emissions of CO₂ and H₂O. For a lignin-rich precursor, at masses above inflection point, TG can be employed for concurrent pyrolysis characterization and biochar synthesis for application-specific NGC investigations.