Porous crystalline conjugated macrocyclic materials and their energy storage applications

Porous crystalline conjugated macrocyclic materials (CMMs) possess high porosity, tunable structure/function and efficient charge transport ability owing to their planar macrocyclic conjugated π-electron system, which make them promising candidates for applications in energy storage. In this review, we thoroughly summarize the timely development of porous crystalline CMMs in energy storage related fields. Specifically, we summarize and discuss their structures and properties. In addition, their energy storage applications, such as lithium ion batteries, lithium sulfur batteries, sodium ion batteries, potassium ion batteries, Li-CO2 batteries, Li-O2 batteries, Zn-air batteries, supercapacitors and triboelectric nanogenerators, are also discussed. Finally, we present the existing challenges and future prospects. We hope this review will inspire the development of advanced energy storage materials based on porous crystalline CMMs.

Application of μ-Nitrido- and μ-Carbido-Bridged Iron Phthalocyanine Dimers as Cathode-Active Materials for Rechargeable Batteries

μ-Nitrido- and μ-carbido-bridged iron phthalocyanine dimers, when used as cathode-active materials for rechargeable lithium batteries, showed four stable redox waves in cyclic voltammetry studies in solution and a stable discharge capacity of approximately 60 mAh g^-1 after 200 cycles. These results indicate that μ-heteroatom-bridged iron phthalocyanine dimers are good platforms for designing novel phthalocyanine-based electrode-active materials.

1,4,5,8-Naphthalenetetracarboxylic dianhydride grafted phthalocyanine macromolecules as an anode material for lithium ion batteries

For solving the problems of high solubility in electrolytes, poor conductivity and low active site utilization of organic electrode materials, in this work, 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTCDA) grafted nickel phthalocyanine (TNTCDA-NiPc) was synthesized and used as an anode material for lithium ion batteries. As a result, the dispersibility, conductivity and dissolution stability are improved, which is conducive to enhancing the performance of batteries. The initial discharge capacity of the TNTCDA-NiPc electrode is 859.8 mA h g^-1 at 2 A g^-1 current density, which is much higher than that of the NTCDA electrode (247.4 mA h g^-1). After 379 cycles, the discharge capacity of the TNTCDA-NiPc electrode is 1162.9 mA h g^-1, and the capacity retention rate is 135.3%, which is 7 times that of the NTCDA electrode. After NTCDA is grafted to the phthalocyanine macrocyclic system, the dissolution of the NTCDA in the electrolyte is reduced, and the conductivity and dispersion of the NTCDA and phthalocyanine ring are also improved, so that more active sites of super lithium intercalation from NTCDA and phthalocyanine rings are exposed, which results in better electrochemical performance. The strategy of grafting small molecular active compounds into macrocyclic conjugated systems used in this work can provide new ideas for the development of high performance organic electrode materials.

Porous diatomite-mixed 1,4,5,8-NTCDA nanowires as high-performance electrode materials for lithium-ion batteries

A porous composite electrode composed of diatomite-mixed 1,4,5,8-naphthalenetetracarboxylic dianhydride (NTCDA) is prepared by electrostatic spinning technology. Compared with traditional coated electrodes without diatomite mixing, the obtained composite electrode materials have higher porosity, larger specific surface area and faster lithium ion transport channels, which makes them exhibit better electrochemical performance, such as smaller impedance, higher capacity, and better cycling stability and rate performance. The electrospun diatomite-mixed 1,4,5,8-NTCDA composite (ED-1,4,5,8-NTCDA) electrode shows an initial coulombic efficiency of 77.2%, which is much higher than that of the electrospun 1,4,5,8-NTCA (E-1,4,5,8-NTCDA) electrode without diatomite mixing (63.8%) and the coated 1,4,5,8-NTCA (C-1,4,5,8-NTCDA) electrode (48.3%). Moreover, the ED-1,4,5,8-NTCDA electrode displays an initial discharge capacity of 1106.5 mA h g-1, which is much higher than that of the E-1,4,5,8-NTCDA electrode (546.0 mA h g-1) and the C-1,4,5,8-NTCDA electrode (185.4 mA h g-1). After 200 cycles, the capacity of the ED-1,4,5,8-NTCDA electrode remains at 1008.5 mA h g-1 with a retention ratio of 91.2%, which is also much higher than that of 753.2 mA h g-1 for the E-1,4,5,8-NTCDA electrode and 288.1 mA h g-1 for the C-1,4,5,8-NTCDA electrode. Even at a higher current density of 1500 mA g-1, its capacity remains above 508.9 mA h g-1. The ED-1,4,5,8-NTCDA electrode presents superior performance, which opens up a promising new approach for further utilization of organic materials as electrode materials in rechargeable lithium-ion batteries.

Current mapping of lead phthalocyanine thin films in the presence of gaseous dopants

Iodine doping in nonplanar Pb(ii)phthalocyanine causes significant structural reorganization and enhanced conductance with nanoscale conducting pathways and improved sensitivity towards other gaseous adsorbates.