Filler-Enhanced Piezoelectricity of Poly-L-Lactide and Its Use as a Functional Ultrasound-Activated Biomaterial

Poly-L-lactide (PLLA) offers a unique possibility for processing into biocompatible, biodegradable, and implantable piezoelectric structures. With such properties, PLLA has potential to be used as an advanced tool for mimicking biophysical processes that naturally occur during the self-repair of wounds and damaged tissues, including electrostimulated regeneration. The piezoelectricity of PLLA strongly depends on the possibility of controlling its crystallinity and molecular orientation. Here, it is shown that modifying PLLA with a small amount (1 wt%) of crystalline filler particles with a high aspect ratio, which act as nucleating agents during drawing-induced crystallization, promotes the formation of highly crystalline and oriented PLLA structures. This increases their piezoelectricity, and the filler-modified PLLA films provide a 20-fold larger voltage output than nonmodified PLLA during ultrasound (US)-assisted activation. With 99% PLLA content, the ability of the films to produce reactive oxygen species (ROS) and increase the local temperature during interactions with US is shown to be very low. US-assisted piezostimulation of adherent cells directly attach to their surface (such as skin keratinocytes), stimulate cytoskeleton formation, and as a result cells elongate and orient themselves in a specific direction that align with the direction of PLLA film drawing and PLLA dipole orientation.

Piezoelectric Nanogenerators Based On BaTiO3/PDMS Composites for High-Frequency Applications

A series of highly flexible and environmentally friendly composites based on polydimethylsiloxane (PDMS) filled with 200 nm size ferroelectric BaTiO₃ (BTO) particles at different concentrations (from 7 to 23 vol %) have been fabricated by a simple dispersion method. The dielectric, piezoelectric, and ultrasonic properties have been studied. The ferroelectric state of BTO was confirmed by differential scanning calorimetry and ultrasonic spectroscopy. The addition of BTO into PDMS strongly affects the dielectric properties of the composites. At low temperatures close to 160 K, the PDMS matrix exhibits a dielectric anomaly related to a dynamic glass transition, which shifts to higher temperatures as the BTO content increases due to the strong interaction between polymer chains and nanoparticles. Ultrasonic measurements demonstrate the appearance of a piezoelectric voltage signal on a thin plate of the composite with the highest available filler concentration (23 vol %) under longitudinal stress applied by a 10 MHz ultrasonic wave. As a result, at room temperature, the detected signal is characterized by output voltage and specific stored energy values of 10 mV and 367.3 MeV/m², respectively, followed by a further increase with cooling to 35 mV at 150 K. The proposed BTO/PDMS composite system is thus a potential candidate for nanogenerators, namely, a simple, flexible, and lead-free device converting high-frequency (10 MHz) mechanical vibrations into electrical voltage.

Intelligent wearable devices based on nanomaterials and nanostructures for healthcare

Emerging classes of flexible electronic sensors as alternatives to conventional rigid sensors offer a powerful set of capabilities for detecting and quantifying physiological and physical signals from human skin in personal healthcare. Unfortunately, the practical applications and commercialization of flexible sensors are generally limited by certain unsatisfactory aspects of their performance, such as biocompatibility, low sensing range, power supply, or single sensory function. This review intends to provide up-to-date literature on wearable devices for smart healthcare. A systematic review is provided, from sensors based on nanomaterials and nanostructures, algorithms, to multifunctional integrated devices with stretchability, self-powered performance, and biocompatibility. Typical electromechanical sensors are investigated with a specific focus on the strategies for constructing high-performance sensors based on nanomaterials and nanostructures. Then, the review emphasizes the importance of tailoring the fabrication techniques in order to improve stretchability, biocompatibility, and self-powered performance. The construction of wearable devices with high integration, high performance, and multi-functionalization for multiparameter healthcare is discussed in depth. Integrating wearable devices with appropriate machine learning algorithms is summarized. After interpretation of the algorithms, intelligent predictions are produced to give instructions or predictions for smart implementations. It is desired that this review will offer guidance for future excellence in flexible wearable sensing technologies and provide insight into commercial wearable sensors.

Perovskite Piezoelectric-Based Flexible Energy Harvesters for Self-Powered Implantable and Wearable IoT Devices

In the ongoing fourth industrial revolution, the internet of things (IoT) will play a crucial role in collecting and analyzing information related to human healthcare, public safety, environmental monitoring and home/industrial automation. Even though conventional batteries are widely used to operate IoT devices as a power source, these batteries have a drawback of limited capacity, which impedes broad commercialization of the IoT. In this regard, piezoelectric energy harvesting technology has attracted a great deal of attention because piezoelectric materials can convert electricity from mechanical and vibrational movements in the ambient environment. In particular, piezoelectric-based flexible energy harvesters can precisely harvest tiny mechanical movements of muscles and internal organs from the human body to produce electricity. These inherent properties of flexible piezoelectric harvesters make it possible to eliminate conventional batteries for lifetime extension of implantable and wearable IoTs. This paper describes the progress of piezoelectric perovskite material-based flexible energy harvesters for self-powered IoT devices for biomedical/wearable electronics over the last decade.

High Energy Storage Density in Nanocomposites of P(VDF-TrFE-CFE) Terpolymer and BaZr0.2Ti0.8O3 Nanoparticles

Polymer materials are actively used in dielectric capacitors, in particular for energy storage applications. An enhancement of the stored energy density can be achieved in composites of electroactive polymers and dielectric inorganic fillers with a high dielectric permittivity. In this article, we report on the energy storage characteristics of composites of relaxor terpolymer P(VDF-TrFE-CFE) and BaZr_0.2Ti_0.8O₃ (BZT) nanoparticles. The choice of materials was dictated by their large dielectric permittivity in the vicinity of room temperature. Free-standing composite films, with BZT contents up to 5 vol.%, were prepared by solution casting. The dielectric properties of the composites were investigated over a wide range of frequencies and temperatures. It was shown that the addition of the BZT nanoparticles does not affect the relaxor behavior of the polymer matrix, but significantly increases the dielectric permittivity. The energy storage parameters were estimated from the analysis of the unipolar polarization hysteresis loops. The addition of the BZT filler resulted in the increasing discharge energy density. The best results were achieved for composites with 1.25–2.5 vol.% of BZT. In the range of electric fields to 150 MV/m, the obtained materials demonstrate a superior energy storage density compared to other P(VDF-TFE-CFE) based composites reported in the literature.

Ferroelectric Polymer Nanofibers Reminiscent of Morphotropic Phase Boundary Behavior for Improved Piezoelectric Energy Harvesting

Ferroelectric and piezoelectric polymers have attracted great attention from many research and engineering fields due to its mechanical robustness and flexibility as well as cost-effectiveness and easy processibility. Nevertheless, the electrical performance of piezoelectric polymers is very hard to reach that of piezoelectric ceramics basically and physically, even in the case of the representative ferroelectric polymer, poly(vinylidene fluoride-co-trifluoroethylene) (P(VDF-TrFE)). Very recently, the concept for the morphotropic phase boundary (MPB), which has been exclusive in the field of high-performance piezoelectric ceramics, has been surprisingly confirmed in P(VDF-TrFE) piezoelectric copolymers by the groups. This study demonstrates the exceptional behaviors reminiscent of MPB and relaxor ferroelectrics in the feature of widely utilized electrospun P(VDF-TrFE) nanofibers. Consequently, an energy harvesting device that exceeds the performance limitation of the existing P(VDF-TrFE) materials is developed. Even the unpoled MPB-based P(VDF-TrFE) nanofibers show higher output than the electrically poled normal P(VDF-TrFE) nanofibers. This study is the first step toward the manufacture of a new generation of piezoelectric polymers with practical applications.

Progress in lead-free piezoelectric nanofiller materials and related composite nanogenerator devices

Current piezoelectric device systems need a significant reduction in size and weight so that electronic modules of increasing capacity and functionality can be incorporated into a great range of applications, particularly in energy device platforms. The key question for most applications is whether they can compete in the race of down-scaling and an easy integration with highly adaptable properties into various system technologies such as nano-electro-mechanical systems (NEMS). Piezoelectric NEMS have potential to offer access to a parameter space for sensing, actuating, and powering, which is inflential and intriguing. Fortunately, recent advances in modelling, synthesis, and characterization techniques are spurring unprecedented developments in a new field of piezoelectric nano-materials and devices. While the need for looking more closely at the piezoelectric nano-materials is driven by the relentless drive of miniaturization, there is an additional motivation: the piezoelectric materials, which are showing the largest electromechanical responses, are currently toxic lead (Pb)-based perovskite materials (such as the ubiquitous Pb(Zr,Ti)O3, PZT). This is important, as there is strong legislative and moral push to remove toxic lead compounds from commercial products. By far, the lack of viable alternatives has led to continuing exemptions to allow their temporary use in piezoelectric applications. However, the present exemption will expire soon, and the concurrent improvement of lead-free piezoelectric materials has led to the possibility that no new exemption will be granted. In this paper, the universal approaches and recent progresses in the field of lead-free piezoelectric nano-materials, initially focusing on hybrid composite materials as well as individual nanoparticles, and related energy harvesting devices are systematically elaborated. The paper begins with a short introduction to the properties of interest in various piezoelectric nanomaterials and a brief description of the current state-of-the-art for lead-free piezoelectric nanostructured materials. We then describe several key methodologies for the synthesis of nanostructure materials including nanoparticles, followed by the discussion on the critical current and emerging applications in detail.

Innovation Strategy Selection Facilitates High-Performance Flexible Piezoelectric Sensors

Piezoelectric sensors with high performance and low-to-zero power consumption meet the growing demand in the flexible microelectronic system with small size and low power consumption, which are promising in robotics and prosthetics, wearable devices and electronic skin. In this review, the development process, application scenarios and typical cases are discussed. In addition, several strategies to improve the performance of piezoelectric sensors are summed up: (1) material innovation: from piezoelectric semiconductor materials, inorganic piezoceramic materials, organic piezoelectric polymer, nanocomposite materials, to emerging and promising molecular ferroelectric materials. (2) designing microstructures on the surface of the piezoelectric materials to enlarge the contact area of piezoelectric materials under the applied force. (3) addition of dopants such as chemical elements and graphene in conventional piezoelectric materials. (4) developing piezoelectric transistors based on piezotronic effect. In addition, the principle, advantages, disadvantages and challenges of every strategy are discussed. Apart from that, the prospects and directions of piezoelectric sensors are predicted. In the future, the electronic sensors need to be embedded in the microelectronic systems to play the full part. Therefore, a strategy based on peripheral circuits to improve the performance of piezoelectric sensors is proposed in the final part of this review.