Protease-sensitive atelocollagen hydrogels promote healing in a diabetic wound model

Mechanical and suture-holding properties of a UV-cured atelocollagen membrane with varied crosslinked architecture

The mechanical competence and suturing ability of collagen-based membranes are paramount in guided bone regeneration (GBR) therapy, to ensure damage-free implantation, fixation and space maintenancein vivo. However, contact with the biological medium can induce swelling of collagen molecules, yielding risks of membrane sinking into the bone defect, early loss of barrier function, and irreversibly compromised clinical outcomes. To address these challenges, this study investigates the effect of the crosslinked network architecture on both mechanical and suture-holding properties of a new atelocollagen (AC) membrane. UV-cured networks were obtained via either single functionalisation of AC with 4-vinylbenzyl chloride (4VBC) or sequential functionalisation of AC with both 4VBC and methacrylic anhydride. The wet-state compression modulus (Ec) and swelling ratio (SR) were significantly affected by the UV-cured network architecture, leading up to a three-fold reduction in SR and about two-fold increase inEcin the sequentially functionalised, compared to the single-functionalised, samples. Electron microscopy, dimensional analysis and compression testing revealed the direct impact of the ethanol series dehydration process on membrane microstructure, yielding densification of the freshly synthesised porous samples and a pore-free microstructure with increasedEc. Nanoindentation tests via spherical bead-probe atomic force microscopy (AFM) confirmed an approximately two-fold increase in median (interquartile range (IQR)) elastic modulus in the sequentially functionalised (EAFM= 40 (13) kPa), with respect to single-functionalised (EAFM= 15 (9) kPa), variants. Noteworthy, the single-functionalised, but not the sequentially functionalised, samples displayed higher suture retention strength (SRS = 28 ± 2-35 ± 10 N∙mm-1) in both the dry state and following 1 h in phosphate buffered saline (PBS), compared to Bio-Gide® (SRS: 6 ± 1-14 ± 2 N∙mm-1), while a significant decrease was measured after 24 h in PBS (SRS= 1 ± 1 N∙mm-1). These structure-property relationships confirm the key role played by the molecular architecture of covalently crosslinked collagen, aimed towards long-lasting resorbable membranes for predictable GBR therapy.

Bioarchitectural Design of Bioactive Biopolymers: Structure-Function Paradigm for Diabetic Wound Healing

Chronic wounds such as diabetic ulcers are a major complication in diabetes caused by hyperglycemia, prolonged inflammation, high oxidative stress, and bacterial bioburden. Bioactive biopolymers have been found to have a biological response in wound tissue microenvironments and are used for developing advanced tissue engineering strategies to enhance wound healing. These biopolymers possess innate bioactivity and are biodegradable, with favourable mechanical properties. However, their bioactivity is highly dependent on their structural properties, which need to be carefully considered while developing wound healing strategies. Biopolymers such as alginate, chitosan, hyaluronic acid, and collagen have previously been used in wound healing solutions but the modulation of structural/physico-chemical properties for differential bioactivity have not been the prime focus. Factors such as molecular weight, degree of polymerization, amino acid sequences, and hierarchical structures can have a spectrum of immunomodulatory, anti-bacterial, and anti-oxidant properties that could determine the fate of the wound. The current narrative review addresses the structure-function relationship in bioactive biopolymers for promoting healing in chronic wounds with emphasis on diabetic ulcers. This review highlights the need for characterization of the biopolymers under research while designing biomaterials to maximize the inherent bioactive potency for better tissue regeneration outcomes, especially in the context of diabetic ulcers.

A collagen-based theranostic wound dressing with visual, long-lasting infection detection capability

Continuous wound monitoring is one strategy to minimise infection severity and inform prompt variations in therapeutic care following infection diagnosis. However, integration of this functionality in therapeutic wound dressings is still challenging. We hypothesised that a theranostic dressing could be realised by integrating a collagen-based wound contact layer with previously demonstrated wound healing capability, and a halochromic dye, i.e. bromothymol blue (BTB), undergoing colour change following infection-associated pH changes (pH: 5-6 ➔ >7). Two different BTB integration strategies, i.e. electrospinning and drop-casting, were pursued to introduce long-lasting visual infection detection capability through retention of BTB within the dressing. Both systems had an average BTB loading efficiency of 99 wt% and displayed a colour change within 1 min of contact with simulated wound fluid. Drop-cast samples retained up to 85 wt% of BTB after 96 h in a near-infected wound environment, in contrast to the fibre-bearing prototypes, which released over 80 wt% of BTB over the same time period. An increase in collagen denaturation temperature (DSC) and red shifts (ATR-FTIR) suggest the formation of secondary interactions between the collagen-based hydrogel and the BTB, which are attributed to count for the long-lasting dye confinement and durable dressing colour change. Given the high L929 fibroblast viability in drop-cast sample extracts (92 %, 7 days), the presented multiscale design is simple, cell- and regulatory-friendly, and compliant with industrial scale-up. This design, therefore, offers a new platform for the development of theranostic dressings enabling accelerated wound healing and prompt infection diagnosis.

Barrier Membranes for Guided Bone Regeneration (GBR): A Focus on Recent Advances in Collagen Membranes

Guided bone regeneration (GBR) has become a clinically standard modality for the treatment of localized jawbone defects. Barrier membranes play an important role in this process by preventing soft tissue invasion outgoing from the mucosa and creating an underlying space to support bone growth. Different membrane types provide different biological mechanisms due to their different origins, preparation methods and structures. Among them, collagen membranes have attracted great interest due to their excellent biological properties and desired bone regeneration results to non-absorbable membranes even without a second surgery for removal. This work provides a comparative summary of common barrier membranes used in GBR, focusing on recent advances in collagen membranes and their biological mechanisms. In conclusion, the review article highlights the biological and regenerative properties of currently available barrier membranes with a particular focus on bioresorbable collagen-based materials. In addition, the advantages and disadvantages of these biomaterials are highlighted, and possible improvements for future material developments are summarized.

Multifunctional hydrogels for wound dressings using xanthan gum and polyacrylamide

Developing advanced dressings that integrate multiple functions is one of the major challenges in current clinical wound treatment. In this study, Xanthan gum (XG) and polyacrylamide (PAAm) materials were used to prepare hydrogel dressings by one-pot method. With the combination of the PAAm network and the XG network, the PAAm-XG hydrogels showed the tensile strength of 0.36 MPa and the stretchability as large as 2078 %. The prepared PAAm-XG hydrogels had excellent water uptake efficiency with the swelling ratio of 1200 %. Besides, the developed dressings possessed outstanding biocompatibility, universal adhesion and self-healing ability. More importantly, the PAAm-XG hydrogels can be successfully loaded with Cefixime and human recombinant epidermal growth factor, and these loaded hydrogels released these bioactive molecules in sustained ways. As a result, both E. coli and S. aureus bacteria were inactivated after contacting with the Cefixime-loaded hydrogels for 24 h. Furthermore, in vivo data demonstrated that the PAAm-XG hydrogel dressings significantly accelerated the wound healing in a mouse model. All of these indicate that the multifunctional PAAm-XG hydrogels are promising candidates for wound treatment.

Functionalized gelatin/strontium hydrogel bearing endothelial progenitor cells for accelerating angiogenesis in wound tissue regeneration

While polymer hydrogels are frequently utilized as wound dressings, they lack the sufficient bioactivity necessary to promote re-epithelialization and angiogenesis. In this work, a therapeutic angiogenesis complex is developed using a mixture of dopamine-modified polyhedral oligomeric silsesquioxane (Dopa-POSS), strontium ions (Sr2+ ions) photocrosslinked gelatin methacryloyl (GelMA) hydrogel and endothelial progenitor cells (EPCs) for full-thickness burn wound healing. Dopa-POSS is used to reinforce the hydrogel, and Sr2+ ions stabilizer is densely incorporated inside the network of GelMA hydrogels by ultraviolet cross-linking, thus effectively enhancing the hydrogel mechanical strength. The multifunctional GelMA hydrogels comprised gelatin's arginine-glycine-aspartate (RGD) patterns and active Sr2+ ions that promote EPC biological activity and proliferation. Notably, the Sr2+ ions in the functional hydrogels substantially enhanced EPC proliferation in a three-dimensional environment, migration, and angiogenesis-related protein expression. After 14 days, the Gel/Sr2+@POSS/EPCs composite hydrogel substantially accelerates and enhances the new blood vessel development process, collagen deposition, and re-epithelialization with the almost closed wounds and newly created tissue. Thus, UV-crosslinked Gel/Sr2+@POSS hydrogels functionalized with EPCs can be a potentially beneficial therapeutic system for full-thickness burn wound healing.

A long-lasting guided bone regeneration membrane from sequentially functionalised photoactive atelocollagen

The fast degradation of collagen-based membranes in the biological environment remains a critical challenge, resulting in underperforming Guided Bone Regeneration (GBR) therapy leading to compromised clinical results. Photoactive atelocollagen (AC) systems functionalised with ethylenically unsaturated monomers, such as 4-vinylbenzyl chloride (4VBC), have been shown to generate mechanically competent materials for wound healing, inflammation control and drug delivery, whereby control of the molecular architecture of the AC network is key. Building on this platform, the sequential functionalisation with 4VBC and methacrylic anhydride (MA) was hypothesised to generate UV-cured AC hydrogels with reduced swelling ratio, increased proteolytic stability and barrier functionality for GBR therapy. The sequentially functionalised atelocollagen precursor (SAP) was characterised via TNBS and ninhydrin colourimetric assays, circular dichroism and UV-curing rheometry, which confirmed nearly complete consumption of collagen's primary amino groups, preserved triple helices and fast (< 180 s) gelation kinetics, respectively. Hydrogel's swelling ratio and compression modulus were adjusted depending on the aqueous environment used for UV-curing, whilst the sequential functionalisation of AC successfully generated hydrogels with superior proteolytic stability in vitro compared to both 4VBC-functionalised control and the commercial dental membrane Bio-Gide®. These in vitro results were confirmed in vivo via both subcutaneous implantation and a proof-of-concept study in a GBR calvarial model, indicating integrity of the hydrogel and barrier defect, as well as tissue formation following 1-month implantation in rats. STATEMENT OF SIGNIFICANCE: Collagen-based membranes remain a key component in Guided Bone Regeneration (GBR) therapy, but their properties, e.g. proteolytic stability and soft tissue barrier functionality, are still far from optimal. This is largely attributed to the complex molecular configuration of collagen, which makes chemical accessibility and structure-function relations challenging. Here, we fabricated a UV-cured hydrogel network of atelocollagen, whereby triple helices were sequentially functionalised with two distinct ethylenically unsaturated monomers. The effects of the sequential functionalisation and UV-curing on the macroscopic properties, degradation behaviour and GBR capability were investigated in vitro and in vivo. The results highlight the key role of the sequential functionalisation and provide important insights for the design of future, longer-lasting resorbable membranes for GBR therapy.

Fish Gelatin: Current Nutritional, Medicinal, Tissue Repair Applications and Carrier of Drug Delivery

Gelatin is obtained via partial denaturation of collagen and is extensively used in various industries. The majority of gelatin utilized globally is derived from a mammalian source. Several health and religious concerns associated with porcine/bovine gelatin were reported. Therefore, gelatin from a marine source is widely being investigated for its efficiency and utilization in a variety of applications as a potential substitute for porcine/bovine gelatin. Although fish gelatin is less durable and possesses lower melting and gelling temperatures compared to mammal-derived gelatin, various modifications are being reported to promote its rheological and functional properties to be efficiently employed. The present review describes in detail the current innovative applications of fish gelatin involving the food industry, drug delivery and possible therapeutic applications. Gelatin bioactive molecules may be utilized as carriers for drug delivery. Due to its versatility, gelatin can be used in different carrier systems, such as microparticles, nanoparticles, fibers and hydrogels. The present review also provides a perspective on the other potential pharmaceutical applications of fish gelatin, such as tissue regeneration, antioxidant supplementation, antihypertensive and anticancer treatments.

Subcutaneous toxicity of a dual ionically cross-linked atelocollagen and sodium hyaluronate gel: Rat in vivo study for biological safety evaluation of the injectable hydrogel

•

Hydrogel wound dressings are commonly used to stop bleeding and enhance healing.

•

Hyaluronic acid and collagen are beneficial for wound healing, however, each polymer has limitations.

•

A dual hydrogel combining the benefits of both biopolymers can be more effective for the treatment of various wound types.

•

A composite of collagen and sodium hyaluronate did not generate significant subacute toxicity or reactivity in vivo.

Hydrogels are commonly used in wound dressing, as they retain moisture, accelerate healing, and break down necrotic tissue. This process enhances patient comfort levels while simultaneously reducing pain caused by dead tissue. The purpose of this study was to investigate the in vivo toxicity of a dual hydrogel consisting of type I atelocollagen cross-linked with sodium hyaluronate hydrogel used for wound dressing.

Porcine type I atelocollagen was cross-linked with sodium hyaluronate to form the hydrogel. For subcutaneous implantation, 0.5 ml of dual hydrogel was injected into two different sites of twenty rats per group. High density polyethylene rods were implanted subcutaneously to serve as a control material. Hematological assessment, blood biochemistry, histopathological, and histological evaluations were scored and graded after 4 weeks. A bioreactivity rating was used for evaluation of subacute toxicity.

Differences observed in blood chemical analysis and hematological analysis between control and test groups were within normal variations and considered unrelated to the test article implantation. No significant implantation-related lesions were observed in any of the major organs of all test animals. The overall histopathological index of the test article implantation sites was evaluated as 0. The bioreactivity rating was evaluated as non-irritant after 4-week subcutaneous implantation.

Overall, these results indicate that the dual hydrogel of type I atelocollagen and sodium hyaluronate is biologically and chemically safe for clinical application as a wound dressing.

Hierarchically Assembled Type I Collagen Fibres as Biomimetic Building Blocks of Biomedical Membranes

Wet spinning is an established fibre manufacturing route to realise collagen fibres with preserved triple helix architecture and cell acceptability for applications in biomedical membranes. However, resulting fibres still need to be chemically modified post-spinning to ensure material integrity in physiological media, with inherent risks of alteration of fibre morphology and with limited opportunities to induce fibrillogenesis following collagen fixation in the crosslinked state. To overcome this challenge, we hypothesised that a photoactive type I collagen precursor bearing either single or multiple monomers could be employed to accomplish hierarchically assembled fibres with improved processability, macroscopic properties and nanoscale organisation via sequential wet spinning and UV-curing. In-house-extracted type I rat tail collagen functionalised with both 4-vinylbenzyl chloride (4VBC) and methacrylate residues generated a full hydrogel network following solubilisation in a photoactive aqueous solution and UV exposure, whereby ~85 wt.% of material was retained following 75-day hydrolytic incubation. Wide-angle X-ray diffraction confirmed the presence of typical collagen patterns, whilst an averaged compression modulus and swelling ratio of more than 290 kPa and 1500 wt.% was recorded in the UV-cured hydrogel networks. Photoactive type I collagen precursors were subsequently wet spun into fibres, displaying the typical dichroic features of collagen and regular fibre morphology. Varying tensile modulus (E = 5 ± 1 - 11 ± 4 MPa) and swelling ratio (SR = 1880 ± 200 - 3350 ± 500 wt.%) were measured following post-spinning UV curing and equilibration with phosphate-buffered saline (PBS). Most importantly, 72-h incubation of the wet spun fibres in PBS successfully induced renaturation of collagen-like fibrils, which were fixed following UV-induced network formation. The whole process proved to be well tolerated by cells, as indicated by a spread-like cell morphology following a 48-h culture of L929 mouse fibroblasts on the extracts of UV-cured fibres.

Structurally Dynamic Hydrogels for Biomedical Applications: Pursuing a Fine Balance between Macroscopic Stability and Microscopic Dynamics

Owing to their unique chemical and physical properties, hydrogels are attracting increasing attention in both basic and translational biomedical studies. Although the classical hydrogels with static networks have been widely reported for decades, a growing number of recent studies have shown that structurally dynamic hydrogels can better mimic the dynamics and functions of natural extracellular matrix (ECM) in soft tissues. These synthetic materials with defined compositions can recapitulate key chemical and biophysical properties of living tissues, providing an important means to understanding the mechanisms by which cells sense and remodel their surrounding microenvironments. This review begins with the overall expectation and design principles of dynamic hydrogels. We then highlight recent progress in the fabrication strategies of dynamic hydrogels including both degradation-dependent and degradation-independent approaches, followed by their unique properties and use in biomedical applications such as regenerative medicine, drug delivery, and 3D culture. Finally, challenges and emerging trends in the development and application of dynamic hydrogels are discussed.

Sustained delivery of MMP-9 siRNA via thermosensitive hydrogel accelerates diabetic wound healing

Excessive expression of matrix metalloproteinase 9 (MMP-9) impedes healing of diabetic chronic wounds, thus wound dressing that could effectively inhibit the expression of MMP-9 offers significant clinical translation for diabetic wound healing. Herein, a hybrid hydrogel dressing was developed for localized and sustained delivery of MMP-9 siRNA (siMMP-9). siMMP-9 was complexed with Gly-TETA (GT), the GT/siMMP9 complex was then loaded into a thermosensitive hydrogel based on Pluronic F-127 (PF) and methylcellulose (MC). In vitro, this hybrid hydrogel dressing exhibited negligible cytotoxicity, prolonged the release of GT/siMMP-9 for up to 7 days, and significantly reduced MMP-9 expression. In vivo assessment in diabetic rats demonstrated that hydrogel provided localized and sustained delivery via the thermosensitive controlled release of entrapped GT/siMMP-9 into wound tissues for 7 days, resulting in dramatic MMP-9 silencing which significantly improved diabetic wound closure. This hybrid hydrogel dressing exhibited excellent biocompatibility, with no observed systemic toxicity in rats. Taken together, the hybrid hydrogel dressing may constitute an effective and biocompatible means of enhancing diabetic wound healing through effective silencing of the MMP-9 gene, and this hydrogel delivery system also offers a platform for in vivo delivery of siRNA for the treatment of other diseases.

Rose Bengal Crosslinking to Stabilize Collagen Sheets and Generate Modulated Collagen Laminates

For medical application, easily accessible biomaterials with tailored properties are desirable. Collagen type I represents a biomaterial of choice for regenerative medicine and tissue engineering. Here, we present a simple method to modify the properties of collagen and to generate collagen laminates. We selected three commercially available collagen sheets with different thicknesses and densities and examined the effect of rose bengal and green light collagen crosslinking (RGX) on properties such as microstructure, swelling degree, mechanical stability, cell compatibility and drug release. The highest impact of RGX was measured for Atelocollagen, for which the swelling degree was reduced from 630% (w/w) to 520% (w/w) and thickness measured under force application increased from 0.014 mm to 0.455 mm, indicating a significant increase in mechanical stability. Microstructural analysis revealed that the sponge-like structure was replaced by a fibrous structure. While the initial burst effect during vancomycin release was not influenced by crosslinking, RGX increased cell proliferation on sheets of Atelocollagen and on Collagen Solutions. We furthermore demonstrate that RGX can be used to covalently attach different sheets to create materials with combined properties, making the modification and combination of readily available sheets with RGX an attractive approach for clinical application.

Polydopamine-assisted PDGF-BB immobilization on PLGA fibrous substrate enhances wound healing via regulating anti-inflammatory and cytokine secretion

Platelet-derived growth factor-bb (PDGF-BB) is a potent chemokine and mitogen for fibroblasts, keratinocytes, and vascular endothelium in the injured area, believed to be effective in wound healing. However, the short half-life of PDGF-BB and its rapid release from the wound surface limited its efficacy in vivo and vitro. To evaluate the wound healing effects of dorsal skin in SD rats with polydopamine-assisted immobilized PDGF-BB on PLGA nanofibrous substrate. First, the effects of pDA-coating and PDGF-BB immobilization on the morphology, compositions, and hydrophilicity of substrates were evaluated in details. Second, the wound healing effect of pDA/PLGA/PDGF-BB substrate was assessed in the dorsal skin of SD rats. Last, the cytokine analysis by ELISA method was employed to evaluate the advantages of pDA/PLGA/PDGF-BB substrate on anti-inflammatory, angiogenesis, and cellular proliferation. This method significantly improved the immobilization amount and stability of PDGF-BB on the substrate (p<0.01), further improved the hydrophilicity of substrates (p<0.05). Furthermore, the wound closure process was much more accelerated in the pDA/PLGA/PDGF-BB group (p<0.05). H&E and CD31 staining informed that the wound treated by pDA/PLGA/PDGF-BB substrate showed a high degree of regeneration and angiogenesis. The cytokine analysis showed that pDA significantly reduced the high level of inflammatory cytokines such as TNF-α (p<0.05). And the immobilized PDGF-BB significantly elevated the level of TGF-β and VEGF (p<0.05). The pDA/PLGA/PDGF-BB substrate showed great therapeutic effect on wound healing compared with other control groups via regulating anti-inflammatory, angiogenesis, and cellular proliferation. Absolutely, this report offered an available novel method for skin regeneration.

A redox-responsive hyaluronic acid-based hydrogel for chronic wound management

Polymer-based hydrogels have been widely applied for chronic wound therapeutics, due to their well-acclaimed wound exudate management capability. At the same time, there is still an unmet clinical need for simple wound diagnostic tools to assist clinical decision-making at the point of care and deliver on the vision of patient-personalised wound management. To explore this challenge, we present a one-step synthetic strategy to realise a redox-responsive, hyaluronic acid (HA)-based hydrogel that is sensitive to wound environment-related variations in glutathione (GSH) concentration. By selecting aminoethyl disulfide (AED) as a GSH-sensitive crosslinker and considering GSH concentration variations in active and non-self-healing wounds, we investigated the impact of GSH-induced AED cleavage on hydrogel dimensions, aiming to build GSH-size relationships for potential point-of-care wound diagnosis. The hydrogel was also found to be non-cytotoxic and aided L929 fibroblast growth and proliferation over seven days in vitro. Such a material offers a very low-cost tool for the visual detection of a target analyte that varies dependent on the status of the cells and tissues (wound detection), and may be further exploited as an implant for fibroblast growth and tissue regeneration (wound repair).

Targeting MMP-9 in Diabetic Foot Ulcers

Diabetic foot ulcers (DFUs) are significant complications of diabetes and an unmet medical need. Matrix metalloproteinases (MMPs) play important roles in the pathology of wounds and in the wound healing process. However, because of the challenge in distinguishing active MMPs from the two catalytically inactive forms of MMPs and the clinical failure of broad-spectrum MMP inhibitors in cancer, MMPs have not been a target for treatment of DFUs until recently. This review covers the discovery of active MMP-9 as the biochemical culprit in the recalcitrance of diabetic wounds to healing and targeting this proteinase as a novel approach for the treatment of DFUs. Active MMP-8 and MMP-9 were observed in mouse and human diabetic wounds using a batimastat affinity resin and proteomics. MMP-9 was shown to play a detrimental role in diabetic wound healing, whereas MMP-8 was beneficial. A new class of selective MMP-9 inhibitors shows clinical promise for the treatment of DFUs.

Monomer-Induced Customization of UV-Cured Atelocollagen Hydrogel Networks

The covalent functionalization of type I atelocollagen with either 4-vinylbenzyl or methacrylamide residues is presented as a simple synthetic strategy to achieve customizable, cell-friendly UV-cured hydrogel networks with widespread clinical applicability. Molecular parameters, i.e., the type of monomer, degree of atelocollagen functionalization and UV-curing solution, have been systematically varied and their effect on gelation kinetics, swelling behavior, elastic properties, and enzymatic degradability investigated. UV-cured hydrogel networks deriving from atelocollagen precursors functionalized with equivalent molar content of 4-vinylbenzyl (F 4VBC = 18 ± 1 mol.%) and methacrylamide (F MA = 19 ± 2 mol.%) adducts proved to display remarkably-different swelling ratio (SR = 1963 ± 58-5202 ± 401 wt.%), storage modulus (G' = 17 ± 3-390 ± 99 Pa) and collagenase resistance (μ rel = 18 ± 5-56 ± 5 wt.%), similarly to the case of UV-cured hydrogel networks obtained with the same type of methacrylamide adduct, but varied degree of functionalization (F MA = 19 ± 2 - 88 ± 1 mol.%). UV-induced network formation of 4VBC-functionalized atelocollagen molecules yielded hydrogels with increased stiffness and enzymatic stability, attributed to the molecular rigidity of resulting aromatized crosslinking segment, whilst no toxic response was observed with osteosarcoma G292 cells. Although to a lesser extent, the pH of the UV-curing solution also proved to affect macroscopic hydrogel properties, likely due to the altered organization of atelocollagen molecules during network formation. By leveraging the knowledge gained with classic synthetic networks, this study highlights how the type of monomer can be conveniently exploited to realize customizable atelocollagen hydrogels for personalized medicine, whereby the structure-property relationships can be controlled to meet the requirements of unmet clinical applications.

A simple strategy for robust preparation and characterisation of hydrogels derived from chitosan and amino functional monomers for biomedical applications

Molecular interactions of amino functional (AF) monomers with chitosan (CS) lead to the formation of external stimuli responsive hydrogels (HGs). These have the potential to produce biomaterials with novel properties by a simple blending approach. Six independent AF monomers such as diethylenetriamine (DETA), bis(3-aminopropyl)amine (BAPA), 3,3'-diamino-N-methyldipropyleamine (DAMPA), hexamethylenediamine (HMDA), N,N-dimethylethylamine (DMEA) and diethylamine (DEA) with distinct functional groups and chain lengths were designed to form stable HGs at physiological pH. Such AF monomers are able to form HGs within a short time (in the range from 10 to 19 seconds) by physically interacting with CS. This is an alternative to the covalently crosslinking reaction process, providing cost effective HG biomaterials. HG complexes were characterized by rheometry, differential scanning calorimetry (DSC), and Fourier transform infrared (FTIR) spectroscopy. The interaction between AF monomers and the CS polymer has been discussed and the results have been confirmed by FTIR analysis. The storage modulus (G'), loss modulus (G'') and complex viscosity (η*) were evaluated for all HGs using a rheometer, and the ratios of CS and the particular AF monomer were optimized for stable HG formation. The swelling ratio was evaluated using a simple method and was found to be directly related to the structure of the AF monomer, pH and temperature. These HGs were utilised for encapsulation, and the release of active molecules (e.g., reactive red 120 (RR120) as a model compound) was measured at low pH 5.5, physiological pH 7.4 and high pH 9.5. The cell viability and cellular compatibility of the HGs were evaluated in vitro cell culture, demonstrating that all the five different types of HGs support cellular compatibility, attachment and growth. The physical mixing of AF monomers with CS is expedited for the development of new bespoke economically viable biomaterials.

Review: Multimodal bioactive material approaches for wound healing

Wound healing is a highly complex process of tissue repair that relies on the synergistic effect of a number of different cells, cytokines, enzymes, and growth factors. A deregulation in this process can lead to the formation of a non-healing chronic ulcer. Current treatment options, such as collagen wound dressings, are unable to meet the demand set by the wound environment. Therefore, a multifaceted bioactive dressing is needed to elicit a targeted affect. Wound healing strategies seek to develop a targeted effect through the delivery of a bioactive molecule to the wound by a hydrogel or a polymeric scaffold. This review examines current biomaterial and small molecule-based approaches that seek to develop a bioactive material for targeted wound therapy and accepted wound healing models for testing material efficacy.

Electro-responsive graphene oxide hydrogels for skin bandages: The outcome of gelatin and trypsin immobilization

A free radical polymerization method was adopted for the fabrication of hybrid hydrogel films based on acrylamide and polyethylene glycol dimethacrylate as plasticizing and crosslinking agents, respectively, to be employed as smart skin bandages. Electro-sensitivity, biocompatibility and proteolytic properties were conferred to the final polymer networks by introducing graphene oxide (0.5% w/w), gelatin or trypsin (10% w/w) in the polymerization feed. The physical chemical and mechanical characterization of hybrid materials was performed by means of determination of protein content, Raman spectroscopy, thermogravimetric analysis and measurement of tensile strength. The evaluation of both water affinity and curcumin release profiles (analyzed by suitable mathematical modelling) upon application of an external electric stimulation in the 0-48 voltage range, confirmed the possibility to modulate the release kinetics. Proper proteolytic tests showed that the trypsin enzymatic activity was retained by 80% upon immobilization. Moreover, for all samples, we observed a viability higher than 94% in normal human fibroblast cells (MRC-5), while a reduction of methicillin-resistant Staphylococcus aureus CFU mL^-1 (90%) was obtained with curcumin loaded samples.

3D-printing porosity: A new approach to creating elevated porosity materials and structures

We introduce a new process that enables the ability to 3D-print high porosity materials and structures by combining the newly introduced 3D-Painting process with traditional salt-leaching. The synthesis and resulting properties of three 3D-printable inks comprised of varying volume ratios (25:75, 50:50, 70:30) of CuSO₄ salt and polylactide-co-glycolide (PLGA), as well as their as-printed and salt-leached counterparts, are discussed. The resulting materials are comprised entirely of PLGA (F-PLGA), but exhibit porosities proportional to the original CuSO₄ content. The three distinct F-PLGA materials exhibit average porosities of 66.6-94.4%, elastic moduli of 112.6-2.7 MPa, and absorbency of 195.7-742.2%. Studies with adult human mesenchymal stem cells (hMSCs) demonstrated that elevated porosity substantially promotes cell adhesion, viability, and proliferation. F-PLGA can also act as carriers for weak, naturally or synthetically-derived hydrogels. Finally, we show that this process can be extended to other materials including graphene, metals, and ceramics.

STATEMENT OF SIGNIFICANCE

Porosity plays an essential role in the performance and function of biomaterials, tissue engineering, and clinical medicine. For the same material chemistry, the level of porosity can dictate if it is cell, tissue, or organ friendly; with low porosity materials being far less favorable than high porosity materials. Despite its importance, it has been difficult to create three-dimensionally printed structures that are comprised of materials that have extremely high levels of internal porosity yet are surgically friendly (able to handle and utilize during surgical operations). In this work, we extend a new materials-centric approach to 3D-printing, 3D-Painting, to 3D-printing structures made almost entirely out of water-soluble salt. The structures are then washed in a specific way that not only extracts the salt but causes the structures to increase in size. With the salt removed, the resulting medical polymer structures are almost entirely porous and contain very little solid material, but the maintain their 3D-printed form and are highly compatible with adult human stem cells, are mechanically robust enough to use in surgical manipulations, and can be filled with and act as carriers for biologically active liquids and gels. We can also extend this process to three-dimensionally printing other porous materials, such as graphene, metals, and even ceramics.

Self-assembly of collagen-based biomaterials: preparation, characterizations and biomedical applications

By combining regulatory parameters with characterization methods, researchers can selectively fabricate collagenous biomaterials with various functional responses for biomedical applications.

A hydroxamic acid–methacrylated collagen conjugate for the modulation of inflammation-related MMP upregulation

The selective covalent coupling of hydroxamic acid functions on to methacrylated type I collagen led to UV-cured networks with inherent MMP-modulating capability and enhanced proteolytic stability.

Thiol-Ene Photo-Click Collagen-PEG Hydrogels: Impact of Water-Soluble Photoinitiators on Cell Viability, Gelation Kinetics and Rheological Properties

Thiol-ene photo-click hydrogels were prepared via step-growth polymerisation using thiol-functionalised type-I collagen and 8-arm poly(ethylene glycol) norbornene-terminated (PEG-NB), as a potential injectable regenerative device. Type-I collagen was thiol-functionalised by a ring opening reaction with 2-iminothiolane (2IT), whereby up to 80 Abs.% functionalisation and 90 RPN% triple helical preservation were recorded via 2,4,6-Trinitrobenzenesulfonic acid (TNBS) colorimetric assay and circular dichroism (CD). Type, i.e., either 2-Hydroxy-1-[4-(2-hydroxyethoxy) phenyl]-2-methyl-1-propanone (I2959) or lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP), and concentration of photoinitiator were varied to ensure minimal photoinitiator-induced cytotoxicity and to enable thiol-ene network formation of collagen-PEG mixtures. The viability of G292 cells following 24 h culture in photoinitiator-supplemented media was largely affected by the photoinitiator concentration, with I2959-supplemented media observed to induce higher toxic response (0.1 → 0.5% (w/v) I2959, cell survival: 62 → 2 Abs.%) compared to LAP-supplemented media (cell survival: 86 → 8 Abs.%). In line with the in vitro study, selected photoinitiator concentrations were used to prepare thiol-ene photo-click hydrogels. Gelation kinetics proved to be largely affected by the specific photoinitiator, with LAP-containing thiol-ene mixtures leading to significantly reduced complete gelation time (τ: 187 s) with respect to I2959-containing mixtures (τ: 1683 s). Other than the specific photoinitiator, the photoinitiator concentration was key to adjusting the hydrogel storage modulus (G'), whereby 15-fold G' increase (232 → 3360 Pa) was observed in samples prepared with 0.5% (w/v) compared to 0.1% (w/v) LAP. Further thiol-ene formulations with 0.5% (w/v) LAP and varied content of PEG-NB were tested to prepare photo-click hydrogels with porous architecture, as well as tunable storage modulus (G': 540⁻4810 Pa), gelation time (τ: 73⁻300 s) and swelling ratio (SR: 1530⁻2840 wt %). The photoinitiator-gelation-cytotoxicity relationships established in this study will be instrumental to the design of orthogonal collagen-based niches for regenerative medicine.