Silver nanocrystal-decorated polyoxometalate single-walled nanotubes as nanoreactors for desulfurization catalysis at room temperature

Polymer-induced self-assembly strategy toward 3D printable porous MoO3/Al2O3 catalyst for efficient oxidative desulfurization

Porous metal oxides have attracted much attention due to their large number of internal crosslinking channels and higher specific surface areas in the fields of heterogeneous catalysis. Herein, a solvent-free polymer-induced self-assembly strategy is reported for the preparation of porous metal oxides by the strong interaction between polymers and inorganic precursors in a high-energy ball milling process. The 5 %MoO3/Al2O3 catalyst has a stratified pore structure and high surface area. Meanwhile, due to the introduction of the active component molybdenum oxide, the abundant low-price molybdenum species and the corresponding oxygen vacancy are retained, which shows high catalytic oxidative desulfurization performance for a variety of aromatic sulfides, especially the intractable 4,6-DMDBT. The 3D printing ink with excellent viscoelasticity is prepared by the composite of powder porous metal oxides and montmorillonite, and the monolithic catalyst is obtained by direct ink writing 3D printing technology. This research provides a new idea for the design and fabrication of high efficiency catalysts.

Mn-Based Mullites for Environmental and Energy Applications

Mn-based mullite oxides AMn2O5 (A = lanthanide, Y, Bi) is a novel type of ternary catalyst in terms of their electronic and geometric structures. The coexistence of pyramid Mn3+-O and octahedral Mn4+-O makes the d-orbital selectively active toward various catalytic reactions. The alternative edge- and corner-sharing stacking configuration constructs the confined active sites and abundant active oxygen species. As a result, they tend to show superior catalytic behaviors and thus gain great attention in environmental treatment and energy conversion and storage. In environmental applications, Mn-based mullites have been demonstrated to be highly active toward low-temperature oxidization of CO, NO, volatile organic compounds (VOCs), etc. Recent research further shows that mullites decompose O3 and ozonize VOCs from -20 °C to room temperature. Moreover, mullites enhance oxygen reduction reactions (ORR) and sulfur reduction reactions (SRR), critical kinetic steps in air-battery and Li-S batteries, respectively. Their distinctive structures also facilitate applications in gas-sensitive sensing, ionic conduction, high mobility dielectrics, oxygen storage, piezoelectricity, dehydration, H2O2 decomposition, and beyond. A comprehensive review from basic physicochemical properties to application certainly not only gains a full picture of mullite oxides but also provides new insights into designing heterogeneous catalysts.

Modulating the Catalytic Properties of Polyoxovanadates with Transition-Metal-Complex Units for Selective Oxidation of Sulfides

Selective oxidation of sulfides to sulfoxides is of great significance in the synthesis of pharmaceuticals, desulfurization of fuels, and detoxification of sulfur mustard chemical warfare agents. Designing selective catalysts to achieve the efficient transformation of sulfides to sulfoxides is thus highly desired. Herein, we report three transition metal-complex-functionalized polyoxovanadates, [Zn2(BPB)2][V4O12]·0.5BPB·H2O (1), [Ni(BPB)(H2O)][V2O6]·2H2O (2), and [Co(HBPB)2][V4O12] (3) (BPB = 1,4-bis(pyrid-4-yl)benzene)), and explore their applications for selective oxidation of sulfides using H2O2 as an oxidant. All three compounds were catalytically effective for the oxidation of methyl phenyl sulfide to methyl phenyl sulfoxide, with 1 being best-performing with complete conversion and a selectivity of 96.7%. In the selective oxidation of a series of aromatic and aliphatic sulfides to corresponding sulfoxides, 1 also showed satisfactory performance; in particular, the chemical warfare agent stimulant 2-chloroethyl ethyl sulfide can be completely and selectively oxidized to the nontoxic 2-chloroethyl ethyl sulfoxide within 20 min at room temperature. Catalyst 1 can be recycled and reused at least six times with uncompromised performance. The perfect performance of 1 is attributed to the synergistic effect of coordinatively unsaturated V and Zn sites in bimetallic oxide, as revealed by comparative structural and catalytic studies.

Single-Walled Cluster Nanotubes for Single-Atom Catalysts with Precise Structures

Spatially confining isolated atomic sites in low-dimensional nanostructures is a promising strategy for preparing high-performance single-atom catalysts (SACs). Herein, fascinating polyoxometalate cluster-based single-walled nanotubes (POM-SWNTs) with atomically precise structures, uniform diameter, and single-cluster wall thickness are constructed by lacunary POM clusters (PW11 and P2W17 clusters). Isolated metal centers are accurately incorporated into the PW11-SWNTs and P2W17-SWNTs supports. The structures of the resulting MPW11-SWNTs and MP2W17-SWNTs are well established (M = Cu, Pt). Molecular dynamics simulations demonstrate the stability of POM-SWNTs. Furthermore, the turnover frequency of PtP2W17-SWNTs is 20 times higher than that of PtP2W17 cluster units and 140 times higher than that of Pt nanoparticles in the alcoholysis of dimethylphenylsilane. Theoretical studies indicate that incorporating a Pt atom into the P2W17 support induces straightforward electron transfer between them, combining the nanoconfined environment to enhance the catalytic activity of PtP2W17-SWNTs. This work shows the feasibility of using subnanometric POM clusters to assemble single-walled cluster nanotubes, highlighting their potential to prepare superior SACs with precise structures.

ZnO-POM Cluster Sub-1 nm Nanosheets as Robust Catalysts for the Oxidation of Thioethers at Room Temperature

Two-dimensional (2D) zinc oxides have attracted more and more research interests due to their unique properties. Yet, it remains a great challenge to limit the thickness to the sub-1 nm scale and further combine with other components to obtain 2D hybrid zinc oxide (ZnO)-based sub-1 nm materials. Herein, a versatile strategy was successfully developed to realize the controllable preparation of ZnO-polyoxometalate (POM)-based 2D hybrid sub-1 nm nanosheet (HSNS) superstructures by incorporating three kinds of molybdenum-based POM clusters into the zinc oxide system. Molecular dynamics simulation results demonstrated that POM clusters interact with ZnO/Zn(OH)₂ molecules and coassembled into stable 2D HSNSs. Significantly, theses materials as robust catalysts showed excellent catalytic activity, selectivity, and stability in the oxidation of thioethers at room temperature, which partly can be attributed to the special 2D sub-1 nm nanostructures with large specific areas leading to the full exposure of active sites. Meanwhile, the synergetic effect of multiple components also played an important role during the catalytic process. Thus, this work would pave the way for the precise synthesis of multicomponent 2D hybrid sub-1 nm materials for widespread applications.

A current overview of the oxidative desulfurization of fuels utilizing heat and solar light: from materials design to catalysis for clean energy

The ceaseless increase of pollution cases due to the tremendous consumption of fossil fuels has steered the world towards an environmental crisis and necessitated urgency to curtail noxious sulfur oxide emissions. Since the world is moving toward green chemistry, a fuel desulfurization process driven by clean technology is of paramount significance in the field of environmental remediation. Among the novel desulfurization techniques, the oxidative desulfurization (ODS) process has been intensively studied and is highlighted as the rising star to effectuate sulfur-free fuels due to its mild reaction conditions and remarkable desulfurization performances in the past decade. This critical review emphasizes the latest advances in thermal catalytic ODS and photocatalytic ODS related to the design and synthesis routes of myriad materials. This encompasses the engineering of metal oxides, ionic liquids, deep eutectic solvents, polyoxometalates, metal-organic frameworks, metal-free materials and their hybrids in the customization of advantageous properties in terms of morphology, topography, composition and electronic states. The essential connection between catalyst characteristics and performances in ODS will be critically discussed along with corresponding reaction mechanisms to provide thorough insight for shaping future research directions. The impacts of oxidant type, solvent type, temperature and other pivotal factors on the effectiveness of ODS are outlined. Finally, a summary of confronted challenges and future outlooks in the journey to ODS application is presented.

In Situ Implanting of Single Tungsten Sites into Defective UiO-66(Zr) by Solvent-Free Route for Efficient Oxidative Desulfurization at Room Temperature

Design of single-site catalysts with catalytic sites at atomic-scale and high atom utilization, provides new opportunities to gain superior catalytic performance for targeted reactions. In this contribution, we report a one-pot green approach for in situ implanting of single tungsten sites (up to 12.7 wt.%) onto the nodes of defective UiO-66(Zr) structure via forming Zr-O-W bonds under solvent-free condition. The catalysts displayed extraordinary activity for the oxidative removal of sulfur compounds (1000 ppm S) at room temperature within 30 min. The turnover frequency (TOF) value can reach 44.0 h^-1 at 30 °C, which is 109.0, 12.3 and 1.2 times higher than that of pristine UiO-66(Zr), WO₃ , and WCl₆ (homogeneous catalyst). Theoretical and experimental studies show that the anchored W sites can react with oxidant readily and generate W^VI -peroxo intermediates that determine the reaction activity. Our work not only manifests the application of SSCs in the field of desulfurization of fuel oil but also opens a new solvent-free avenue for fabricating MOFs based SSCs.

Sub-Nanometer Nanobelts Based on Titanium Dioxide/Zirconium Dioxide-Polyoxometalate Heterostructures

In addition to offering conformational flexibility, sub-nanometer nanobelts (SNBs) also outperform many larger nanobelts with large size owing to their ultrathin morphologies. However, to date, only a few monocomponent SNBs have been synthesized. This study presents a facile method for synthesizing ZrO₂ -PMoO (PMZ) SNBs and TiO₂ -PMoO (PMT) SNBs with heterostructures. The SNBs comprise ZrO₂ /TiO₂ and polyoxometalate (POM) nanoclusters, which are formed via the aggregation and subsequent transformation of nanoclusters. Significantly, these SNBs demonstrate high catalytic activity and stability in oxidative desulfurization reactions at room temperature. The impressive catalytic performance of the SNBs is aided by the POM nanoclusters, which not only coassemble with ZrO₂ /TiO₂ nuclei to form building blocks of PMZ SNBs/PMT SNBs but also serve as catalytic centers. The catalytic performance is further enhanced by the ZrO₂ /TiO₂ in the SNBs. Moreover, the proposed synthesis method can be utilized to produce other SNBs. Thus, this method provides valuable insights into the strong performance properties of SNBs created by combining metal oxides and POM nanoclusters into SNBs, which have great potential as redox catalysts.

Two-dimensional ultrathin surfactant-encapsulating polyoxometalate assemblies as carriers for monodispersing noble-metal nanoparticles with high catalytic activity and stability

Noble metal nanoparticles (NMNPs) with excellent catalytic activity and stability play an important role in the field of environmental governance. A uniform distribution and a strong binding force with the carriers of the noble metal nanoparticles are important, but avoidance of the use of additional reducing agents is a promising direction of research. Herein, 2D ultrathin surfactant-encapsulating polyoxometalate (SEP) nanosheets constructed by the self-assembly of dodecyldimethylammonium bromide (DODA) and molybdophosphate (H3PMo12O40, PMo12) are designed to be versatile carriers for Ag nanoparticles. Under the synergistic effect of the well-arranged PMo12 units, encapsulating hydrophobic oleic acid (OA) and reductive molybdophosphate under Xe lamp irradiation, the silver oleate (AgOA)-derived Ag nanoparticles (5 ± 2 nm) are monodispersed on the DODA-PMo12 assemblies and form the Agx/DODA-PMo12 composite. The optimized Ag4.89/DODA-PMo12 composite exhibits high catalytic activity and stability in the degradation of 4-nitrophenol (4-NP), which reaches a superior rate constant of 6.49 × 10-3 s-1 and without significant deterioration after three recycles. This technique can be facilely promoted to other noble metal nanoparticles with excellent catalytic activity and stability.

Vanadium-substituted heteropolyacids (H3+mPW12−mVmO40) encapsulated in Fe3O4@UiO-66 magnetic core–shell microspheres as excellent catalysts for oxidative desulfurization under oxygen

In this study, the novel magnetic core–shell composites Fe₃O₄@UiO-66-HPA, consisting of magnetic Fe₃O₄@UiO-66 and vanadium-substituted Keggin-type heteropolyacid active species supported by Zr-MOF, were prepared via a one-pot method and fully characterized.

Polyoxometalates encapsulated into hollow double-shelled nanospheres as amphiphilic nanoreactors for an effective oxidative desulfurization

Although some catalytic hollow nanoreactors have been fabricated in the past, the encapsulated active species focus on metal nanoparticles, and a method for polyoxometalate (POM)-containing hollow nanoreactors has seldom been developed. Herein, we report a synthetic strategy towards POM-based amphiphilic nanoreactors, where the hollow mesoporous double-shelled SiO₂@C nanospheres were used to encapsulate Keggin-type H₃PMo₁₂O₄₀ (PMo₁₂). The outer hydrophobic carbon shell was beneficial for the enrichment of the organic substrate around the nanoreactor and simultaneously prevented the deposition of POMs on the outer surface of the nanoreactor. The inner hydrophilic silica cavity was modified by two types of organosilanes, which not only created an amphiphilic cavity environment but also acted as an anchor to mobilize PMo₁₂. As the POM nanoreactor had the hydrophilic@hydrophobic SiO₂@C shell and an amphiphilic cavity, both dibenzothiophene (DBT) and H₂O₂ could smoothly diffuse into the nanosized cavity, where the DBT was effectively oxidized (conversion: >99%) by the immobilized PMo₁₂ under mild conditions. Importantly, the control experiments indicated that the confined effect of nanoreactor, amphiphilic SiO₂@C double-shell, unique cavity environment, and mesoporous channels accounted for an excellent catalytic performance. Moreover, the nanoreactor was robust and could be reused for five cycles without loss of activity.

Self-Assembly of Ultrathin Nanocrystals to Multidimensional Superstructures

The self-assembly of ultrathin nanocrystals (UTNCs) into well-organized multidimensional superstructures is one of the key topics in material chemistry and physics. Highly ordered nanocrystal assemblies also known as superstructures or synthetic structures have remained a focus for researchers over the past few years due to synergy in their properties as compared to their components. Here, we aim to present the recent progress being made in this field with highlights of our research group endeavors in the engineering of self-assembled complex multidimensional superstructures of various inorganic materials, including polyoxometalates. The driving forces for the assembly process and its kinetics along with the potential applications associated with these unique ordered and spatially complex superstructures are also discussed.

Z-scheme Ag3PO4/POM/GO heterojunction with enhanced photocatalytic performance for degradation and water splitting

To develop solar light-driven photocatalysts with high activity and structural stability, Ag₃PO₄/POM/GO heterojunction has been successfully prepared by a facile method at room temperature.