Cross-linked solid-liquid interfaces enable a fast proton transport in the aluminate heterostructure electrolyte

Having a highly-conductive protonic electrolyte is an essential requirement of developing solid ceramic fuel cell (SCFC) operated below 600 °C. Proton transport in solid electrolyte structure occurs via a bulk conduction mechanism in conventional SCFC, which may not be so efficient; therefore we have developed a fast proton conducting NaAlO₂/LiAlO₂ (NAO-LAO) heterostructure electrolyte, achieving the ionic conductivity of 0.23 S cm^-1 thanks to its rich cross-linked solid-liquid interfaces; the SCFC employing this new developed electrolyte showed a maximum power density of 844 mW cm^-2 at 550 °C, and the fuel cell could still operate at even lower temperatures down to 370 °C, although the output reduced to 90 mW cm^-2. The proton-hydration liquid layer promoted the formation of cross-linked solid-liquid interfaces in the NAO-LAO electrolyte, which promoted the construction of solid-liquid hybrid proton transportation channels and effectively reduced polarization loss, leading to high proton conduction at even lower temperatures. This work provides an efficient design approach for developing enabling electrolytes with high proton conductivity for SCFCs to be operated at relatively lower temperatures (300-600 °C) than traditional solid oxide fuel cells which operate above 750 °C.

Energy Storage Mechanism of C12-3-3 with High-Capacity and High-Rate Performance for Li/Mg Batteries

The low specific capacity and Mg non-affinity of graphite limit the energy density of ion rechargeable batteries. Here, we first identify that the monolayer C12-3-3 in sp2-sp3 carbon hybridization with high Li/Mg affinity is an appropriate anode material for Li-ion batteries and Mg-ion batteries via the first-principles simulations. The monolayer C12-3-3 can achieve high specific capacities of 1181 mAh/g for Li and 739 mAh/g for Mg, higher than those of most previous anodes. The Li storage reaction is an "adsorption-conversion-intercalation mechanism", while the Mg storage reaction is an "adsorption mechanism". The 2D carbon material of C12-3-3 displays fast diffusion kinetics with low diffusion barriers of 0.41 eV for Li and 0.21 eV for Mg. As a new carbon-based anode material, the monolayer C12-3-3 will promote the practical application of batteries with high-capacity and high-rate performance.

Microstructure of the Li-Al-O Second Phases in Garnet Solid Electrolytes

The microstructure of the Li₇La₃Zr₂O₁₂ (LLZO) garnet solid electrolyte is critical for its performance in all-solid-state lithium-ion battery. During conventional high-temperature sintering, second phases are generated at the grain boundaries due to the reaction between sintering aids and LLZO, which have an enormous effect on the performances of LLZO. However, a detailed structure study of the second phases and their impact on physical properties is lacking. Here, crystal structures of the second phases in LLZO pellets are studied in detail by transmission electron microscopy. Three different crystal structures of Li-Al-O second phases, γ-LiAlO₂, α-Li₅AlO₄, and β-Li₅AlO₄ were identified, and atomic-scale lattice information was obtained by applying low-dose high-resolution imaging for these electron-beam-sensitive second phases. On this basis, the structure-property relationship of these structures was explored. It was found that sintering aids with a higher Li/Al ratio are beneficial to form Li-rich second phases, which result in more highly ionic conductive LLZO.

Interfacial-engineering-enabled practical low-temperature sodium metal battery

Solid-state sodium (Na) batteries have received extensive attention as a promising alternative to room-temperature liquid electrolyte Na-ion batteries and high-temperature liquid electrode Na-S batteries because of safety concerns. However, the major issues for solid-state Na batteries are a high interfacial resistance between solid electrolytes and electrodes, and Na dendrite growth. Here we report that a yttria-stabilized zirconia (YSZ)-enhanced beta-alumina solid electrolyte (YSZ@BASE) has an extremely low interface impedance of 3.6 Ω cm² with the Na metal anode at 80 °C, and also exhibits an extremely high critical current density of ~7.0 mA cm^-2 compared with those of other Li- and Na-ion solid electrolytes reported so far. With a trace amount of eutectic NaFSI-KFSI molten salt at the electrolyte/cathode interface, a quasi-solid-state Na/YSZ@BASE/NaNi_0.45Cu_0.05Mn_0.4Ti_0.1O₂ full cell achieves a high capacity of 110 mAh g^-1 with a Coulombic efficiency >99.99% and retains 73% of the cell capacity over 500 cycles at 4C and 80 °C. Extensive characterizations and theoretical calculations prove that the stable β-NaAlO₂-rich solid-electrolyte interphase and strong YSZ support matrix play a critical role in suppressing the Na dendrite as they maintain robust interfacial contacts, lower electronic conduction and prevent the continual reduction of BASE through oxygen-ion compensation.

Use of group 13 aryloxides for the synthesis of green chemicals and oxide materials

In this work, group 13 metal aryloxides [Al(MesalO)3] (1), [Me2Ga(MesalO)]2 (2), [AlLi3(MesalO)6] (3) and [Me2GaLi(MesalO)2(THF)] (4), were obtained by reaction of methyl salicylate (MesalOH) with group-13 alkyls MMe3 (for M...

Atomistic Simulations of the Defect Chemistry and Self-Diffusion of Li-ion in LiAlO2

Lithium aluminate, LiAlO2, is a material that is presently being considered as a tritium breeder material in fusion reactors and coating material in Li-conducting electrodes. Here, we employ atomistic simulation techniques to show that the lowest energy intrinsic defect process is the cation anti-site defect (1.10 eV per defect). This was followed closely by the lithium Frenkel defect (1.44 eV per defect), which ensures a high lithium content in the material and inclination for lithium diffusion from formation of vacancies. Li self-diffusion is three dimensional and exhibits a curved pathway with a migration barrier of 0.53 eV. We considered a variety of dopants with charges +1 (Na, K and Rb), +2 (Mg, Ca, Sr and Ba), +3 (Ga, Fe, Co, Ni, Mn, Sc, Y and La) and +4 (Si, Ge, Ti, Zr and Ce) on the Al site. Dopants Mg2+ and Ge4+ can facilitate the formation of Li interstitials and Li vacancies, respectively. Trivalent dopants Fe3+, Ni3+ and Mn3+ prefer to occupy the Al site with exoergic solution energies meaning that they are candidate dopants for the synthesis of Li (Al, M) O2 (M = Fe, Ni and Mn) compounds.

Suppression of Monoclinic Phase Transitions of O3-Type Cathodes Based on Electronic Delocalization for Na-Ion Batteries

As high capacity cathodes, O3-type Na-based oxides always suffer from a series of monoclinic transitions upon sodiation/desodiation, mainly caused by Na⁺/vacancy ordering and Jahn-Teller (J-T) distortion, leading to rapid structural degradation and serious performance fading. Herein, a simple modulation strategy is proposed to address this issue based on refrainment of electron localization in expectation to alleviate the charge ordering and change of electronic structure, which always lead to Na⁺/vacancy ordering and J-T distortion, respectively. According to density functional theory calculations, Fe³⁺ with slightly larger radius is introduced into NaNi_0.5Mn_0.5O₂ with the intention of enlarging transition metal layers and facilitating electronic delocalization. The obtained NaFe_0.3Ni_0.35Mn_0.35O₂ exhibits a reversible phase transition of O3_hex-P3_hex without any monoclinic transitions in striking contrast with the complicated phase transitions (O3_hex-O'3_mon-P3_hex-P'3_mon-P3'_hex) of NaNi_0.5Mn_0.5O₂, thus excellently improving the capacity retention with a high rate kinetic. In addition, the strategy is also effective to enhance the air stability, proved by direct observation of atomic-scale ABF-STEM for the first time.