Comparison of microwave and mechanochemical energy inputs in the catalytic oxidation of cyclohexane

Investigation of Cerium Reduction Efficiency by Grinding with Microwave Irradiation in Mechanochemical Processing

This study evaluated the efficiency of cerium reduction by grinding with microwave irradiation in mechanochemical processing. Grinding experiments with microwave irradiation were conducted using an agitating mixer. Since the structure of the ground samples was amorphous and the cerium concentration was much lower than those of other elements, the valence change and structural change of cerium after grinding with microwave irradiation were investigated using X-ray absorption fine structure (XAFS) analysis in the cerium K-edge. The X-ray absorption near-edge structure (XANES) analysis revealed that a portion of tetravalent cerium was reduced to trivalent cerium by grinding with microwave irradiation. In addition, it was confirmed by extended X-ray absorption fine structure (EXAFS) analysis that oxygen vacancies were produced as a result of the cerium reduction reaction. To evaluate the efficiency of cerium reduction efficiency, the percentage reduction by grinding with microwave irradiation was compared to that by planetary ball milling and microwave irradiation. As a result, it was revealed that the efficiency of cerium reduction via grinding with microwave irradiation was higher than that via microwave irradiation and the same as that via planetary ball milling. Moreover, a larger amount of tetravalent cerium could be reduced to trivalent cerium by grinding with microwave irradiation than when using planetary ball milling and microwave irradiation.

Glycerol Valorization towards a Benzoxazine Derivative through a Milling and Microwave Sequential Strategy

Glycerol and aminophenol intermolecular condensation has been investigated through a milling and microwave-assisted sequential strategy, towards the synthesis of a benzoxaxine derivative. Mechanochemical activation prior to the microwave-assisted process could improve the probability of contact between the reagents, and greatly favors the higher conversion of aminophenol. At the same time, following a mechanochemical–microwave sequential approach could tune the selectivity towards the formation of a benzoxazine derivative, which could find application in a wide range of biomedical areas.

A comprehensive and updated review of studies on the oxidation of cyclohexane to produce ketone-alcohol (KA) oil

Oxidation of cyclohexane is an essential chemical reaction for the industrial manufacture of cyclohexanol and cyclohexanone. These two compounds, together known as ketone–alcohol (KA) oil, are the main feedstock for nylon 6 and nylon 6,6 productions. Several types of catalysts and reaction conditions have been used for cyclohexane oxidation. This paper presents a thorough literature review of catalytic materials used for cyclohexane oxidation to produce KA oil using oxygen, air and other oxidizing agents as well as utilizing different solvents. This review covers research and development reported over the years 2014–2020. This review aims to comprehend the type of catalysts, solvents, oxidants and other reaction parameters used for the oxidation of cyclohexane. Three types of cyclohexane oxidation processes namely thermocatalytic, photocatalytic and microwave-assisted catalytic have been reported. The results of the review showed that metal and metal oxide loaded silica catalysts performed excellently and provided high selectivity of KA oil and cyclohexane conversion. The use of peroxides is not feasible due to their high price compared to air and oxygen. Gold nanoparticles supported on silica performed with high selectivity and good conversion. The use of hydrochloric acid as an additive was found very effective to enhance the photocatalytic oxidation of cyclohexane. Water on the catalyst surface enhanced the reactivity of the photocatalysts since it helps in the generation of hydroxyl radicals.

Fe(III) Complexes in Cyclohexane Oxidation: Comparison of Catalytic Activities under Different Energy Stimuli

In this study, the mononuclear Fe(III) complex [Fe(HL)(NO3)(H2O)2]NO3 (1) derived from Nʹ-acetylpyrazine-2-carbohydrazide (H2L) was synthesized and characterized by several physicochemical methods, e.g., elemental analysis, infrared (IR) spectroscopy, electrospray ionization mass spectrometry (ESI-MS), and single crystal X-ray diffraction analysis. The catalytic performances of 1 and the previously reported complexes [Fe(HL)Cl2] (2) and [Fe(HL)Cl(μ-OMe)]2 (3) towards the peroxidative oxidation of cyclohexane under three different energy stimuli (microwave irradiation, ultrasound, and conventional heating) were compared. 1-3 displayed homogeneous catalytic activity, leading to the formation of cyclohexanol and cyclohexanone as final products, with a high selectivity for the alcohol (up to 95%). Complex 1 exhibited the highest catalytic activity, with a total product yield of 38% (cyclohexanol + cyclohexanone) under optimized microwave-assisted conditions.

Mechanochemical Preparation of Pd(II) and Pt(II) Composites with Carbonaceous Materials and Their Application in the Suzuki-Miyaura Reaction at Several Energy Inputs

Pd(II) and Pt(II) composites with activated carbon (AC), graphene oxide, and multiwalled carbon nanotubes were prepared by ball milling and used as catalysts for the Suzuki-Miyaura reaction, under several energy inputs (mechanical grinding, conventional heating, and microwave irradiation). The catalytic composites were characterized by ICP-MS, BET, XPS analyses, TEM, and SEM. The average particle size of the prepared composites was estimated to be in the range of 6–30 nm, while the loadings of Pd and Pt did not significantly affect the surface area of the AC support due to the tendency to agglomerate as observed by the TEM analysis. The Pd/AC composites exhibit high mechanochemical catalytic activity in cross-coupling of bromobenzene and phenylboronic acid with molar yields up to 80% with TON and TOF of 222 and 444 h⁻¹, respectively, achieved with Pd(4.7 wt%)-AC catalyst under the liquid assisted grinding for 0.5 h at ambient conditions, using cyclohexene as an additive.

Ferraria A, M. Botelho do Rego A, Correia LMM, Saraiva MS, Pombeiro AJL. Ultrasound and Radiation-Induced Catalytic Oxidation of 1-Phenylethanol to Acetophenone with Iron-Containing Particulate Catalysts

Iron-containing particulate catalysts of 0.1–1 µm size were prepared by wet and ball-milling procedures from common salts and characterized by FTIR, TGA, UV-Vis, PXRD, FEG-SEM, and XPS analyses. It was found that when the wet method was used, semi-spherical magnetic nanoparticles were formed, whereas the mechanochemical method resulted in the formation of nonmagnetic microscale needles and rectangles. Catalytic activity of the prepared materials in the oxidation of 1-phenylethanol to acetophenone was assessed under conventional heating, microwave (MW) irradiation, ultrasound (US), and oscillating magnetic field of high frequency (induction heating). In general, the catalysts obtained by wet methods exhibit lower activities, whereas the materials prepared by ball milling afford better acetophenone yields (up to 83%). A significant increase in yield (up to 4 times) was observed under the induction heating if compared to conventional heating. The study demonstrated that MW, US irradiations, and induction heating may have great potential as alternative ways to activate the catalytic system for alcohol oxidation. The possibility of the synthesized material to be magnetically recoverable has been also verified.

Synergistic catalytic action of vanadia–titania composites towards the microwave-assisted benzoin oxidation

Application of synergistic effects is among the main ways to boost chemical efficiency.

Copper(II) Complexes of Arylhydrazone of 1H-Indene-1,3(2H)-dione as Catalysts for the Oxidation of Cyclohexane in Ionic Liquids

The copper(II) complexes [CuL(H2O)2]∙H2O (1) and [CuL(dea)] (2) [L = 2-(2-(1,3-dioxo-1H-inden-2(3H)-ylidene)hydrazinyl)benzenesulfonate, dea = diethanolamine] were applied as catalysts in the peroxidative (with tert-butyl-hydroperoxide or hydrogen peroxide) conversion of cyclohexane to cyclohexanol and cyclohexanone, either in acetonitrile or in any of the ionic liquids [bmim][NTf2] and [hmim][NTf2] [bmim = 1-butyl-3-methylimidazolium, hmim = 1-hexyl-3-methylimidazolium, NTf2 = bis(trifluoromethanesulfonyl) imide]. Tert-butyl-hydroperoxide led to better product yields, as compared to H2O2, with a selectivity directed towards cyclohexanone. The ILs showed a better performance than the conventional solvent for the copper complex 1. No catalytic activity was observed for 2 in the presence of an IL.