New insights into the organic fouling mechanism of an in situ Ca2+ modified thin film composite forward osmosis membrane

Tailoring properties and performance of thin-film composite membranes by salt additives for water treatment: A critical review

During the fabrication of thin film composite (TFC) membranes by interfacial polymerization (IP), the utilization of salt additives is one of the effective methods to regulate membrane properties and performance. Despite gradually receiving widespread attention for membrane preparation, the strategies, effects and underlying mechanisms of using salt additives have not yet been systematically summarized. This review for the first time provides an overview of various salt additives used to tailor properties and performance of TFC membranes for water treatment. By classifying salt additives into organic and inorganic salts, the roles of added salt additives in the IP process and the induced changes in membrane structure and properties are discussed in detail, and the different mechanisms of salt additives affecting membrane formation are summarized. Based on these mechanisms, the salt-based regulation strategies have shown great potential for improving the performance and application competitiveness of TFC membranes, including overcoming the trade-off relationship between water permeability and salt selectivity, tailoring membrane pore size distribution for precise solute-solute separation, and enhancing membrane antifouling performance. Finally, future research directions are suggested to focus on the long-term stability assessment of salt-modified membranes, the combined use of different salt additives, and the integration of salt regulation with other membrane design or modification strategies.

Reconstruction and Removal Mechanisms of Gel-like Membrane Fouling for Seawater Desalination: Experiments and Molecular Dynamics Simulations

Anti-gel fouling is a key problem faced by membrane desalination, especially for applications in organic acid-rich seawater. In this paper, a chemical crosslinking-based method was used to reconstruct and characterize the gel pollutants produced under the actual operating conditions of seawater desalination. In addition to the calcium alginate/calcium humate three-dimensional network skeleton, salt ions (K+, Na+, Mg2+, Cl−) in solution were also considered to ensure that the reconstructed gel was similar to pollutant gels on membranes under practical operating conditions. Characterizations showed that the reconstructed gel has high thermal insulation and stability, thus adjusting the temperature has no removal effect. Two detergents (sodium citrate and sodium hydroxide) were investigated, and their gel-removal mechanism was elucidated by molecular dynamics simulation. Numerical analysis showed that the electrostatic attraction interaction had a significant role in the gel cleaning process. Owing to the attraction of the lower electrostatic potential region in the cleaning agent, the ion exchange between Na+ in the cleaning agent and Ca2+ in the gel led to the breaking of the Ca2+-induced intermolecular bridge in the complex. As the adhesion of fouling gels decreased, the gel water solubility was increased, resulting in a decrease in weight and strength of the gel. Therefore, the integrity of the gel fouling layer was weakened and can be effectively removed. This study provides a theoretical basis for the removal of gel-like membrane fouling during actual seawater desalination.

Analysis of zwitterionic membrane fouling mechanism caused by HPAM in the presence of electrolytes

Membrane fouling has always been a tough issue that is urgent to solve. Electrolytes which are prevalent in wastewater have a major influence on membrane fouling. Therefore, it is of great significance to understand the role and fouling mechanism of electrolytes in the membrane fouling process. In this work, the zwitterionic membrane is used to process hydrolyzed poly(acrylamide) (HPAM) with the addition of electrolytes (CaCl2, NaCl). Meanwhile, the effect of different electrolytes on the zwitterionic membrane fouling process by hydrolyzed poly(acrylamide) (HPAM) is systematically investigated. It was found that the flux recovery ratio (FRR) of the zwitterionic membrane is nearly 100% after treating HPAM with the addition of electrolytes. Therefore, molecular dynamics (MD) simulations were applied to illustrate the impact of electrolytes on the change of foulant structures and confirm the consequent effect of electrolytes on membrane fouling. According to the experiment and MD simulation results, it is found that the positive ion layer which exists between the HPAM and zwitterionic surface results in the excellent fouling resistance performance of the zwitterionic membrane. The zwitterionic membrane fouling mechanism is analyzed, which is helpful to the understanding of zwitterionic membrane fouling in high salinity wastewater.

Fabrication of High-Performance Thin-Film Composite Nanofiltration Membrane by Dynamic Calcium-Carboxyl Intra-Bridging during Post-Treatment

Widespread applications of nanofiltration (NF) and reverse osmosis (RO)-based processes for water purification and desalination call for high-performance thin-film composite (TFC) membranes. In this work, a novel and facile modification method was proposed to fabricate high-performance thin-film composite nanofiltration membrane by introducing Ca2+ in the heat post-treatment. The introduction of Ca2+ induced in situ Ca2+-carboxyl intra-bridging, leading to the embedment of Ca2+ in the polyamide (PA) layer. This post modification enhanced the hydrophilicity and surface charge of NF membranes compared to the pristine membrane. More interestingly, the modified membrane had more nodules and exhibited rougher morphology. Such changes brought by the addition of Ca2+ enabled the significant increase of water permeability (increasing from 17.9 L·m-2·h-1·bar-1 to 29.8 L·m-2·h-1·bar-1) while maintaining a high selectivity (Na2SO4 rejection rate of 98.0%). Furthermore, the intra-bridging between calcium and carboxyl imparted the NF membranes with evident antifouling properties, exhibiting milder permeability decline of 4.2% (compared to 16.7% of NF-control) during filtration of sodium alginate solution. The results highlight the potential of using Ca2+-carboxyl intra-bridging post-treatment to fabricate high-performance TFC membranes for water purification and desalination.