Engineering active sites in ternary CeO2-CuO-Mn3O4 heterointerface embedded in reduced graphene oxide for boosting water splitting activity

The rational design of highly efficient and stable bifunctional catalysts for overall water splitting is vitally important. In this study, to increase the active catalytic sites of CeO2 for electrochemical water splitting, a ternary CeO2-CuO-Mn3O4 heterostructure, synthesized by coprecipitation method, is loaded on reduced graphene oxide (rGO) nanosheets in different amounts to produce CeO2-CuO-Mn3O4@rGO nanocomposites. It is found that CeO2-CuO-Mn3O4@rGO nanocomposites show higher electrocatalytic activity than unsupported samples, and the best activity is observed when the wieght ratio of CeO2-CuO-Mn3O4 is three times that of rGO. The CeO2-CuO-Mn3O4@rGO(3:1) requires low overpotentials of 130 and 270 mV for hydrogen and oxygen evolution reactions (HER and OER) at a current density of 10 mA cm-2. Furthermore, this material demonstrates a large electrochemically active surface area, low charge transfer resistance, suitable kintics, and high long-term stability for both OER and HER. Additionally, when CeO2-CuO-Mn3O4@rGO(3:1) is used as self-supported electrodes for the overall water splitting reaction, a low cell voltage of 1.68 V is obtained. This superior performance is due to: (i) active multi-metal sites that produce strong synergistic effects; (ii) the high conductivity of rGO, which faciliate favorable electron transfer; and (iii) the homogenous anchoring of CeO2-CuO-Mn3O4 on rGO, which increases the number of active sites available on the catalyst surface.

Multifunctional Fe-S bonds assist poly(3,4-ethylenedioxythiophene) to enhance iron diselenide for ultra-long sodium storage lifetime

Transition metal selenides (TMS) have been used to prepare hundreds of electrode materials for ion batteries due to their superior theoretical capacity, but have been repeatedly limited by the sluggish reaction kinetics and the enormous volume change during the repeated charge/discharge process. Here, we report a facile strategy to fabricate organic-inorganic composites by engineering a unique chemical bonding interface between TMS and conductive polymers. For the first time, poly(3,4-ethylenedioxythiophene) (PEDOT) is utilized to encapsulate iron diselenide (FeSe2) nanoparticles by in situ polymerization, and the Fe-S bonds are meanwhile formed at the interface of FeSe2 and PEDOT. The experimental analysis demonstrates the stability of Fe-S bonds during the sodiation/desodiation process and after long cycling, which can serve as a "bridge" for fast charge transfer and also serve as a "rivet" to stabilize the composite structure. When used for sodium ion storage, the composite offers an exceptionally long lifetime of up to 17,000 loops at 10 A/g without capacity degradation. In addition, it delivers a high specific capacity of 490.4 mAh/g and retains 60 % when the current density is amplified 150 times. The assembled full cell also exhibits excellent cycling stability. This work will provide a feasible way to improve the metal oxide/sulfide/selenides for long-life ion batteries.

Three-dimensional bimodal pore-rich G/MXene sponge amalgamated with vanadium diselenide nanosheets as a high-performance electrode for electrochemical water-oxidation/reduction reactions

Exploring new strategies to design non-precious and efficient electrocatalysts can provide a solution for sluggish electrocatalytic kinetics and sustainable hydrogen energy. Transition metal selenides are potential contenders for bifunctional electrocatalysis owing to their unique layered structure, low band gap, and high intrinsic activities. However, insufficient access to active sites, lethargic water dissociation, and structural degradation of active materials during electrochemical reactions limit their activities, especially in alkaline media. In this article, we report a useful strategy to assemble vanadium diselenide (VSe2) into a 3D MXene/rGO-based sponge-like architecture (VSe2@G/MXe) using hydrothermal and freeze-drying approaches. The 3D hierarchical meso/macro-pore rich sponge-like morphology not only prevents aggregation of VSe2 nanosheets but also offers a kinetics-favorable framework and high robustness to the electrocatalyst. Synergistic coupling of VSe2 and a MXene/rGO matrix yields a heterostructure with a large specific surface area, high conductivity, and multi-dimensional anisotropic pore channels for uninterrupted mass transport and gas diffusion. Consequently, VSe2@G/MXe presented superior electrochemical activity for both the HER and OER compared to its counterparts (VSe2 and VSe2@G), in alkaline media. The overpotentials required to reach a cathodic and anodic current density of 10 mA cm-2 were 153 mV (Tafel slope = 84 mV dec-1) and 241 mV (Tafel slope = 87 mV dec-1), respectively. The Rct values at the open circuit voltage were as low as 9.1 Ω and 1.41 Ω for the HER and OER activity, respectively. Importantly, VSe2@G/MXe withstands a steady current output for a long 24 h operating time. Hence, this work presents a rational design for 3D microstructures with optimum characteristics for efficient bifunctional alkaline water-splitting.

Interfacial Se-O Bonds Modulating Spatial Charge Distribution in FeSe2/Nb:Fe2O3 with Rapid Hole Extraction for Efficient Photoelectrochemical Water Oxidation

Surface engineering is an effective strategy to improve the photoelectrochemical (PEC) catalytic activity of hematite, and the defect states with abundant coordinative unsaturation atoms can serve as anchoring sites for constructing intimate connections between semiconductors. On this basis, we anchored an ultrathin FeSe2 layer on Nb5+-doped Fe2O3 (FeSe2/Nb:Fe2O3) via interfacial Se-O chemical bonds to tune the surface potential. Density functional theory (DFT) calculations indicate that amorphous FeSe2 decoration could generate electron delocalization over the composite photoanodes so that the electron mobility was improved to a large extent. Furthermore, electrons could be transferred via the newly formed Se-O bonds at the interface and holes were collected at the surface of electrode for PEC water oxidation. The desired charge redistribution is in favor of suppressing charge recombination and extracting effective holes. Later, work function calculations and Mott-Schottky (M-S) plots demonstrate that a type-II heterojunction was formed in FeSe2/Nb:Fe2O3, which further expedited carrier separation. Except for spatial carrier modulation, the amorphous FeSe2 layer also provided abundant active sites for intermediates adsorption according to the d band center results. In consequence, the target photoanodes attained an improved photocurrent density of 2.42 mA cm-2 at 1.23 V versus the reversible hydrogen electrode (RHE), 2.5 times as that of the bare Fe2O3. This study proposed a defect-anchoring method to grow a close-connected layer via interfacial chemical bonds and revealed the spatial charge distribution effects of FeSe2 on Nb:Fe2O3, giving insights into rational designation in composite photoanodes.

Activating and optimizing the In-Plane interface of 1 T/2H MoS2 for efficient hydrogen evolution reaction

Implanting the octahedral phase (1 T) into the hexagonal phase (2H) of the molybdenum disulfide (MoS₂) matrix is considered one of the effective methods to enhance hydrogen evolution reaction (HER) performances of MoS₂. In this paper, hybrid 1 T/2H MoS₂ nanosheets array was successfully grown on conductive carbon cloth (1 T/2H MoS₂/CC) via facile hydrothermal method and the 1 T phase content in 1 T/2H MoS₂ is regulated to gradually increase from 0 % to 80 %. 1 T/2H MoS₂/CC with 75 % 1 T phase content exhibits optimal HER performances. The DFT calculation results show that S atoms in 1 T/2H MoS₂ interface exhibit the lowest hydrogen adsorption Gibbs free energies (ΔG_H*) compared with other sites. The improvement of HER performances are primarily attributed to activating the in-plane interface regions of the hybrid 1 T/2H MoS₂ nanosheets. Furthermore, the relationship between 1 T MoS₂ content in 1 T/2H MoS₂ and catalytic activity was simulated by a mathematical model, which shows that the catalytic activity presents a trend of increasing and then decreasing with the increase of 1 T phase content.

Self-supported amorphous phosphide catalytic electrodes for electrochemical hydrogen production coupling with methanol upgrading

Efficient catalytic electrodes for cathodic hydrogen evolution reaction (HER) and anodic oxygen evolution reaction (OER) are pivotal for massive production of green hydrogen from water electrolysis, and the further replacement of kinetically sluggish OER by tailored elecrooxidation of certain organics is a promising way to co-produce hydrogen and value-added chemicals via a more energy-saving and safer manner. Herein, amorphous Ni-Co-Fe ternary phosphides (Ni_xCo_yFe_z-Ps) with different Ni:Co:Fe ratios electrodeposited onto Ni foam (NF) substrate were served as self-supported catalytic electrodes for alkaline HER and OER. The Ni₄Co₄Fe₁-P electrode deposited in solution at Ni:Co:Fe ratio of 4:4:1 displayed low overpotential (61 mV at -20 mA cm^-2) and acceptable durability for HER, while the Ni₂Co₂Fe₁-P electrode fabricated in deposition solution at Ni:Co:Fe ratio of 2:2:1 showed good OER efficiency (overpotential of 275 mV at 20 mA cm^-2) and robust durability, the further replacement of OER by anodic methanol oxidation reaction (MOR) enabled selective production of formate with 110 mV lower anodic potential at 20 mA cm^-2. The HER-MOR co-electrolysis system based on Ni₄Co₄Fe₁-P cathode and Ni₂Co₂Fe₁-P anode could save 1.4 kWh of electric energy per cubic meter of H₂ relative to mere water electrolysis. The current work offers a feasible approach to co-produce H₂ and value-upgraded formate via an energy-saving manner by rational design of catalytic electrodes and construction of co-electrolysis system, and paves the way for cost-effective co-preparation of more value-added organics and green hydrogen via electrolysis.

CeO2/CuO/NiO hybrid nanostructures loaded on N-doped reduced graphene oxide nanosheets as an efficient electrocatalyst for water oxidation and non-enzymatic glucose detection

In this work, the three-component heterostructure of CeO₂/CuO/NiO was synthesized by a co-precipitation procedure and heating at a temperature of 750 °C. Then, CeO₂/CuO/NiO nanoparticles were successfully supported on N-doped reduced graphene oxide (N-rGO) by a hydrothermal method. The obtained nanomaterials were used as effective electrocatalysts for the oxygen evolution reaction and glucose sensing in an alkaline medium. The results indicated that when CeO₂/CuO/NiO is anchored on N-rGO nanosheets, active catalytic sites increase. On the other hand, N-doped rGO enhances electrical conductivity and electron transfer for water or glucose oxidation. CeO₂/CuO/NiO@N-rGO has a large electrochemically active surface area and more active catalytic positions, and thus exhibits high activity for the OER with a low overpotential of 290 mV, a suitable Tafel slope of 110 mV dec^-1, and superior stability and durability for at least 10 hours. CeO₂/CuO/NiO@N-rGO can also detect glucose with a high sensitivity of 912.7 μA mM^-1 cm^-2, a low detection limit of 0.053 μM, a wide linear range between 0.001 and 24 mM, and a short response time of about 2.9 s. Moreover, the high selectivity and stability of this electrode for glucose sensing show its potential for clinical applications.

Introducing High-Valence Iridium Single Atoms into Bimetal Phosphides toward High-Efficiency Oxygen Evolution and Overall Water Splitting

Single atoms are superior electrocatalysts having high atomic utilization and amazing activity for water oxidation and splitting. Herein, this work reports a thermal reduction method to introduce high-valence iridium (Ir) single atoms into bimetal phosphide (FeNiP) nanoparticles toward high-efficiency oxygen evolution reaction (OER) and overall water splitting. The presence of high-valence single Ir atoms (Ir⁴⁺ ) and their synergistic interaction with Ni³⁺ species as well as the disproportionation of Ni³⁺ assisted by Fe collectively contribute to the exceptional OER performance. In specific, at appropriate Ir/Ni and Fe/Ni ratios, the as-prepared Ir-doped FeNiP (Ir₂₅ -Fe₁₆ Ni₁₀₀ P₆₄ ) nanoparticles at a mass loading of only 35 µg cm^-2 show the overpotential as low as 232 mV at 10 mA cm^-2 and activity as high as 1.86 A mg^-1 at 1.5 V versus RHE for OER in 1.0 m KOH. Computational simulations confirm the vital role of high-valence Ir to weaken the adsorption of OER intermediates, favorable for accelerating OER kinetics. Impressively, a Pt/C||Ir₂₅ -Fe₁₆ Ni₁₀₀ P₆₄ two-electrode alkaline electrolyzer affords a current density of 10 mA cm^-2 at a low cell voltage of 1.42 V, along with satisfied stability. An AA battery with a nominal voltage of 1.5 V can drive overall water splitting with obvious bubbles released.

In situ phosphoselenization induced heterointerface engineering endow NiSe2/Ni2P/FeSe2 hollow nanocages with efficient water oxidation electrocatalysis performance

Exploiting Earth-abundant and highly effective electrocatalysts toward the oxygen evolution reaction (OER) is critical for boosting water splitting efficiency. Herein, we proposed a novel in situ phosphoselenization strategy to fabricate heterostructured NiSe₂/Ni₂P/FeSe₂ (NiFePSe) nanocages with a modified electronic structure and well-defined nanointerfaces. Owing to the strong interfacial coupling and synergistic effect among the three components, the prepared NiFePSe nanocages exhibit superior OER performance with an ultralow overpotential of 242 mV at 10 mA cm^-2 and a small Tafel slope of 55.8 mV dec^-1 along with robust stability in 1 M KOH. Remarkably, the highly open 3D porous architecture, delicate internal voids, and numerous surface defects endow the NiFePSe nanocages with abundant active sites and enhanced electron mobility. In addition, the super-hydrophilic surface is conducive to facilitating mass transfer between the electrolyte and electrode and rapidly releasing the bubbles. This work may lead to new breakthroughs in the tuning of multi-component transition metal catalysts and the designing of highly active and durable materials for water splitting.

MXene Nanosheets Induce Efficient Iron Selenide Active Sites to Boost the Electrocatalytic Hydrogen Evolution Reaction

Along with the widespread utilization of hydrogen energy, the rise of highly active hydrogen evolution electrocatalysts with affordable costs presently becomes a substantial crux of this emerging domain. In this work, we demonstrate a feasible and convenient in situ seed-induced growth strategy for the construction of small-sized FeSe₂ nanoparticles decorated on two-dimensional (2D) superthin Ti₃C₂T_x MXene sheets (FeSe₂/Ti₃C₂T_x) through a manipulated bottom-up synthetic procedure. By virtue of the distinctive 0D/2D heterostructures, abundant exposed surface area, well-distributed FeSe₂ catalytic centers, strong surface electronic coupling, and high electrical conductivity, the resultant FeSe₂/Ti₃C₂T_x nanoarchitectures are endowed with a superior electrocatalytic hydrogen evolution capacity including a competitive onset potential of 89 mV, a favorable Tafel slope of 78 mV dec^-1, and a long-period stability, significantly better than that of the pristine FeSe₂ and Ti₃C₂T_x catalysts.

Heterometal doping on nickel selenide corrugations for solar-assisted electrocatalytic hydrogen evolution

Since nickel exhibits good binding energy and is inexpensive, it is widely applied as a hydrogen evolution reaction (HER) electrocatalyst. Among all Ni-based materials, nickel selenide (NiSe) shows a unique electronic structure as a semiconductor with good electrocatalytic activity. Herein, we prepare Co-doped NiSe (Ni_1-xCo_xSe) with a structure of uniform corrugations by one-step chemical vapor deposition. For comparison, Fe-doped NiSe (Ni_1-xFe_xSe) and NiSe are also prepared using the same method. In alkaline electrolyte, Ni_1-xCo_xSe shows great HER performance in terms of low overpotential (93 mV@10 mA cm^-2 and 140 mV@50 mA cm^-2) and long-term stability. Moreover, with the assistance of solar energy, the overpotential needed for Ni_1-xCo_xSe is reduced, making Ni_1-xCo_xSe better than most reported NiSe-based HER catalysts. On the other hand, the current density of Ni_1-xCo_xSe is 13 mA cm^-2@93 mV and 63 mA cm^-2@140 mV with illumination, which is 30% and 26% higher than that without solar illumination assistance, respectively. Therefore, we believe that inducing sunlight to electrocatalytic hydrogen evolution in water splitting could be a supplementary footprint toward the utilization of solar energy.