In vitro biomechanical comparison of a newly designed interlocking nail system to a standard DCP

Mechanical evaluation of a novel angle-stable interlocking nail in a gap fracture model

OBJECTIVE

To describe the mechanical characteristics of a novel angle-stable interlocking nail (NAS-ILN) and compare them to those of a locking compression plate (LCP) by using a gap-fracture model.

STUDY DESIGN

Experimental study.

SAMPLE POPULATION

Synthetic bone models.

METHODS

Synthetic bone models simulating a 50 mm diaphyseal comminuted canine tibial fracture were treated with either a novel angle-stable interlocking nail (NAS-ILN) or a locking compression plate (LCP). Maximal axial deformation and load to failure in compression and 4-point bending, as well as maximal angular deformation, slack, and torque to failure in torsion, were statistically compared (P < .05).

RESULTS

In compression, the maximal axial deformation was lower for NAS-ILN (0.11 mm ± 0.03) than for LCP (1.10 mm ± 0.22) (P < .0001). The ultimate load to failure was higher for NAS-ILN (803.58 N ± 29.52) than for LCP (328.40 N ± 11.01) (P < .0001). In torsion, the maximal angular deformation did not differ between NAS-ILN (22.79° ± 1.48) and LCP (24.36° ± 1.45) (P = .09). The ultimate torque to failure was higher for NAS-ILN (22.45 Nm ± 0.24) than for LCP (19.10 Nm ± 1.36) (P = .001). No slack was observed with NAS-ILN. In 4-point bending, the maximal axial deformation was lower for NAS-ILN (3.19 mm ± 0.49) than for LCP (4.17 mm ± 0.34) (P = .003). The ultimate bending moment was higher for NAS-ILN (25.73 Nm, IQR [23.54-26.86] Nm) than for LCP (16.29 Nm, IQR [15.66-16.47] Nm) (P = .002).

CONCLUSION

The NAS-ILN showed greater stiffness in compression and 4-point bending, and a greater resistance to failure in compression, torsion, and 4-point bending, than LCP.

CLINICAL IMPACT

Based on these results, NAS-ILNs could be considered as alternative implants for the stabilization of comminuted fractures.

Feline Femoral Fracture Fixation: What are the options?

Practical relevance:

The femur is the most commonly fractured bone in cats. Femoral fractures usually result from high-velocity trauma such as a road traffic accident or fall from a height and, as such, are associated with a wide variety of concurrent injuries. The initial focus of treatment should always be on assessment and stabilisation of the major body systems. Once any concurrent injuries have been addressed, all femoral fractures need surgical stabilisation, with the notable exception of greenstick fractures in very young cats, which can heal with cage rest alone. A number of different surgical options are available depending on the fracture type, location, equipment, surgeon experience and owner finances.

Clinical challenges:

Femoral fractures can vary hugely in complexity and the small size of feline bones can limit the choice of implants. Furthermore, cats can present unique challenges in the postoperative period due to their active nature and the limited means to control their exercise level.

Audience:

This review is aimed at general and feline-specific practitioners who have some experience of feline orthopaedics, as well as those simply wishing to expand their knowledge.

Aims:

The aim of this review is to help clinicians assess, plan and manage feline femoral fractures. It provides an overview of diagnostic imaging and a discussion of a range of suitable surgical options, including the principles of different types of fixation. It also highlights cat-specific issues, approaches and implants pertinent to the management of these cases.

Evidence base:

A number of original articles and textbook chapters covering many aspects of femoral fractures in cats and dogs have been published. Where possible, this review draws on information from key feline research and, where necessary, extrapolates from relevant canine literature. The authors also offer practical guidance based on their own clinical experience.

Biomechanical Comparison of Use of Two Screws versus Three Screws Per Fragment with Locking Plate Constructs under Cyclic Loading in Compression in a Fracture Gap Model

OBJECTIVES

 The aim of this study was to measure and compare the stiffness and cyclic fatigue of two plate-bone model constructs, with either two or three locking screws per fragment, under cyclic compression.

METHODS

 A 10-hole 3.5 mm stainless steel locking compression plate (LCP) was fixed 1 mm from a synthetic bone model in which the fracture gap was 47 mm. Two groups of 10 constructs, prepared with either two or three bicortical locking screws placed at the extremities of each fragment, were tested in a load-controlled compression test until failure.

RESULTS

 The three-screw constructs were stiffer than the two-screw constructs (196.75 ± 50.48 N/mm and 102.43 ± 22.93 N/mm, respectively) and the actuator displacements of the two-screw constructs were higher (18.02 ± 1.07 mm) than those of the three-screw constructs (14.48 ± 2.25 mm). The number of cycles to failure of the two-screw constructs was significantly lower (38,337.50 ± 2,196.98) than the that of the three-screw constructs (44,224.00 ± 1,515.24). Load at irreversible deformation was significantly lower in the two-screw constructs (140.93 ± 13.39 N) than in the three-screw constructs (184.27 ± 13.17 N). All constructs failed by plate bending at the gap between the two cylinders.

CLINICAL SIGNIFICANCE

 Omission of the third innermost locking screw during bridging osteosynthesis subjected to compression forces led to a 13.3% reduction in the number of cycles to failure and a 23.5% reduction of the load withstood by the plate before plastic deformation occurred.

Clinical application of the small I-Loc interlocking nail in 30 feline fractures: A prospective study

OBJECTIVE

To describe medium-term functional outcome after nail osteosynthesis in feline traumatology and report clinically relevant recommendations for I-Loc angle-stable interlocking nail use in cats.

STUDY DESIGN

Prospective clinical study.

SAMPLE POPULATION

Client-owned cats (n = 29).

METHODS

Consecutive cases with femoral, tibial, or humeral fractures were included. Outcome measures included fracture and surgical procedure description, limb alignment, nail size vs body weight (BW), percentage of nail medullary canal (MC) fill, time to limb function at clinical union (CU), and complications. Descriptive statistics were reported and compared with historical data.

RESULTS

Bone distribution was 53.3% femora, 30% tibiae, and 16.7% humeri. There were six epimetaphyseal and 24 diaphyseal fractures. Overall, 67% of fractures were comminuted. Open reduction and minimally invasive techniques were used in 73% and 27% of cases, respectively. Seventeen I-Loc 3 (cat mean BW 4.4 ± 2.2 kg) and 13 I-Loc 4 (cat mean BW 5.2 ± 1.2 kg) nails were placed with mean MC fill of ≤50%. Average time to CU was 7.2 weeks. At CU, lameness had resolved or was mild in every cat, and all cats ultimately regained full limb function. No major complications were encountered.

CONCLUSION

Because of improved CU times, excellent functional outcomes, and low complication rate, our results provide evidence that I-Loc nails are safe and effective for feline traumatology.

CLINICAL SIGNIFICANCE

The I-Loc may be advantageous for fixation of epimetaphyseal fractures. Because of feline bone specific dimensional constraints, I-Loc 3 is likely appropriate for all feline humeri and most tibiae, while I-Loc 4 is well sized for feline femora.

Evaluation of a Feline Bone Surrogate and In Vitro Mechanical Comparison of Small Interlocking Nail Systems in Mediolateral Bending

OBJECTIVE

 The aim of this study was to (1) evaluate bending structural properties of a machined short fibre epoxy (SFE) feline bone surrogate (FBS), (2) compare the bending behaviour of small angle-stable interlocking nails (I-Loc; Targon) and locking compression plates (LCP) and (3) evaluate the effect of implant removal on FBS bending strength.

METHODS

 Part 1: Feline cadaveric femurs (n = 10) and FBS (n = 4) underwent cyclic four-point bending and load to failure. Part 2: Fracture gap FBS constructs (n = 4/group) were stabilized in a bridging fashion with either I-Loc 3 and 4, Targon 2.5 and 3.0, LCP 2.0 and 2.4, then cyclically bent. Part 3: Intact FBS with pilot holes, simulating explantation, (n = 4/group) underwent destructive bending tests. Bending compliance, angular deformation and failure moment (F_M) were statistically compared (p < 0.05).

RESULTS

 Native bone and FBS were similar for all outcome measures (p > 0.05). The smallest and largest bending compliance and angular deformation were seen in the I-Loc 4 and LCP 2.0 respectively (p < 0.05). While explanted Targon FBS had the lowest F_M (p < 0.05), I-Loc and LCP constructs F_M were not different (p > 0.05).

CONCLUSION

 The similar bending properties of short fibre epoxy made FBS and native feline femurs suggest that this model could be used for mechanical testing of implants designed for feline long bone osteosynthesis. The I-Loc constructs smaller angular deformation which also suggests that these implants represent a valid alternative to size-matched Targon and LCP for feline fracture osteosynthesis. The significantly lower F_M of explanted Targon may increase the risk of secondary fracture following implant removal.

Biomechanical comparison of a new expandable intramedullary nail and conventional intramedullary nails for femoral osteosynthesis in dogs

Intramedullary nailing of diaphyseal femoral fractures is a commonly used treatment method in dogs because of its biological and biomechanical advantages compared to bone plating. To achieve adequate resistance of the intramedullary nail against torsional and axial compressive forces, additional application of transcortical screws is needed. As these interlocking screws represent a frequent cause of post-operative complications, a new expandable intramedullary nail (EXPN) was developed, which was designed to provide adequate fracture stabilisation without the need for transcortical fixation. The evaluation of the biomechanical properties of the new EXPN with regard to torsional, compressive and bending stability as well as direct comparison to the biomechanical properties of conventional Steinmann (STMN)- and interlocking (ILN) nails was carried out with different biomechanical test arrangements. No significant statistical differences regarding the torsional and bending resistance between the EXPN and ILN group were seen, which indicates that rotatory as well as bending stability of the innovative EXPN is similar to the conventional ILN. Nevertheless, the percentage deviation between the attempted and successfully reached physiological compressive forces was significantly higher (p = 0.045) in the EXPN group compared to the ILN group, which indicates that the compressive stability of the innovative EXPN might be weaker compared to the ILN. In summary, the new EXPN represents an interesting alternative to conventional intramedullary nails. However, in direct comparison to conventional interlocking nails, the EXPN has shown weaknesses in the neutralization of axial compressive forces, which indicates that at least biomechanically the interlocking nail seems advantageous. Further in-vitro and in-vivo investigations are required before clinical use can be recommended.

Mechanical comparison of two small interlocking nails in torsion using a feline bone surrogate

OBJECTIVE

To compare the torsional behavior of two small angle-stable interlocking nails (I-Loc and Targon) with that of locking compression plates (LCP). To evaluate the effect of implant removal on the torsional strength of feline bone surrogates.

STUDY DESIGN

Experimental.

SAMPLE POPULATION

Fracture gap constructs and intact explanted bone surrogates.

METHODS

Fracture gap constructs were stabilized with one of six implants (I-Loc 3 and 4, Targon 2.5 and 3.0, LCP 2.0 and 2.4) and then cyclically tested in torsion (n = 4/group). To simulate implant removal, intact surrogates with implant-specific pilot holes were then twisted to failure (n = 4/group). Torsional compliance (TC; °/Nm), angular deformation (AD; °), and failure torque (F_T ; Nm) were statistically compared (P < .05).

RESULTS

The I-Loc 4 had the smallest TC and AD of all constructs (P < .05). The largest TC (P < .05) was seen with the LCP 2.0. The Targon 2.5 had the largest AD (P < .05) secondary to locking interface slippage. Targon surrogates F_T were the lowest of all groups (P < .05). Conversely, there was no difference between the F_T of the I-Loc, LCP, and intact surrogates (P > .05).

CONCLUSION

We showed that I-Loc nails provided greater torsional stability than size-matched Targon nails and LCPs. Conversely, Targon 2.5 locking interface slippage may jeopardize that construct's stability. Furthermore, the significantly reduced bone surrogate torsional strength provided evidence that the large Targon bolt holes increased the risk of postexplantation iatrogenic fracture.

CLINICAL SIGNIFICANCE

Our results provide evidence to conclude that the small I-Loc nails may be valid alternatives to other osteosynthesis options for feline fracture repair.

Intramedullary nailing biomechanics: Evolution and challenges

This article aims to review the biomechanical evolution of intramedullary nailing and describe the breakthrough concepts which allowed for nail improvement and its current success. The understanding of this field establishes an adequate background for forthcoming research and allows to infer on the path for future developments on intramedullary nailing. It was not until the 1940s, with the revolutionary Küntscher intramedullary nailing design, that this method was recognized as a widespread medical procedure. Such achievement was established based on the foundations created from intuition-based experiments and the first biomechanical ideologies. The nail evolved from allowing alignment and stability through press-fit fixation with nail-cortical wall friction to the nowadays nail stability achieved through interlocking screws mechanical linkage between nail and bone. Important landmarks during nail evolution comprise the introduction of flexible reaming, the progress from slotted to non-slotted nails design, the introduction of nail ‘dynamization’ and the use of titanium alloys as a new nail material. Current biomechanical improvement efforts aim to enhance the bone–intramedullary nail system stability. We suggested that benefit would be attained from a better understanding of the ideal mechano-biological environment at the fracture site, and future improvements will emerge from combining mechanics and biological tools.

Ex vivo torsional properties of a 2.5 mm veterinary interlocking nail system in canine femurs

Objective: To evaluate the torsional properties of the Targon® Vet Nail System (TVS) in small canine femurs and to compare these properties to those of the 2.4 mm LC-DCP® plates.

Methods: Thirty-six cadaveric femurs were allocated to three groups (n = 12). In all bones, points just distal to the lesser trochanter and just proximal to the fabellae were marked and a midshaft transverse osteotomy was performed. Group 1: bones were fixed with the 2.5 mm TVS with the bolts applied at the pre-identified marks. Group 2: A TVS system with 25% shorter inter-bolt distance was used. Group 3: A 7-hole 2.4 mm LCDCP® plates were applied. All constructs were tested non-destructively for 10 cycles, followed by an acute torsion to failure.

Results: Torque at yield was 0.806 ± 0.183 and 0.805 ± 0.093 Nm for groups 1 and 2 and 1.737 ± 0.461 Nm for group 3. Stiffness was 0.05 ± 0.01, 0.05 ± 0.007, and 0.14 ± 0.015 Nm/° for groups 1 to 3 respectively. Maximal angular displacement under cyclic loading was 16.6° ± 2.5°, 15.6° ± 2.1°, and 7.8° ± 1.06° respectively. There was no significant difference for any of the parameters between groups 1 and 2. Both torque at yield and stiffness were significantly greater between group 3 and groups 1 and 2.

Clinical significance: The TVS had approximately half the torsional strength and approximately 1/3 of the stiffness of the 2.4 mm bone plate. Slippage of the locking mechanism was probably the cause of the early failure. The system should be considered as a low-strength and low-stiffness system when compared to bone plates.