Applications of Three-Dimensional Printing in the Management of Complex Aortic Diseases

Planning the use of endografts in the endovascular repair of complex abdominal and thoraco-abdominal aortic lesions leveraging 3D printing

INTRODUCTION

Endovascular techniques and materials have significantly expanded their application in the treatment of abdominal and thoraco-abdominal aortic lesions, allowing for the management of increasingly complex pathologies that may require cannulation of target vessels. The treatment of such diseases deserves a particular approach and dedicated materials, for which correct procedural planning is mandatory. In the last decades, the use of 3D printing technology as an assisting tool for preoperative rehearsal of complex cases has progressively widespread.

AREAS COVERED

A review was performed about the use of 3D printing technology for the planning of endovascular repair of complex abdominal and thoraco-abdominal aortic lesions. Also, our experience of planning and simulation of an elective challenging endovascular procedure for a Crawford's type II thoraco-abdominal aortic aneurysm using a Cook Zenith® T-BranchTM endograft, leveraging a 3D-printed model of the patient-specific anatomy from the aortic arch to the common femoral artery, is herein described.

EXPERT OPINION

The benefits of using 3D printing technologies as an assistive tool in planning complex endovascular repairs of abdominal and thoraco-abdominal aortic lesions have been well-documented in the literature, including their application in urgent cases. However, further research and development are necessary to overcome the current limitations of this potentially highly valuable technology.

Systematic Review on the Use of 3D-Printed Models for Planning, Training and Simulation in Vascular Surgery

The use of 3D-printed models in simulation-based training and planning for vascular surgery is gaining interest. This study aims to provide an overview of the current applications of 3D-printing technologies in vascular surgery. We performed a systematic review by searching four databases: PubMed, Web of Science, Scopus, and Cochrane Library (last search: 1 March 2024). We included studies considering the treatment of vascular stenotic/occlusive or aneurysmal diseases. We included papers that reported the outcome of applications of 3D-printed models, excluding case reports or very limited case series (≤5 printed models or tests/simulations). Finally, 22 studies were included and analyzed. Computed tomography angiography (CTA) was the primary diagnostic method used to obtain the images serving as the basis for generating the 3D-printed models. Processing the CTA data involved the use of medical imaging software; 3DSlicer (Brigham and Women's Hospital, Harvard University, Boston, MA), ITK-Snap, and Mimics (Materialise NV, Leuven, Belgium) were the most frequently used. Autodesk Meshmixer (San Francisco, CA, USA) and 3-matic (Materialise NV, Leuven, Belgium) were the most frequently employed mesh-editing software during the post-processing phase. PolyJet™, fused deposition modeling (FDM), and stereolithography (SLA) were the most frequently employed 3D-printing technologies. Planning and training with 3D-printed models seem to enhance physicians' confidence and performance levels by up to 40% and lead to a reduction in the procedure time and contrast volume usage to varying extents.

Coral reef aorta: a rare form of obstruction of the ascending aorta in adolescent with aortopathy- case report

BACKGROUND

Supra aortic obstruction in children is uncommon and is seen in certain unique conditions. While intraluminal obstruction due to heavy calcification is seen in older populations, it is not described in pediatric populations. The coral reef aorta is a rare and distinct calcifying disease causing luminal obstruction of the suprarenal aorta in adults. The definition of this diagnosis relies entirely on the unique aspects and consistency of the lesions, which are rock-hard, irregular, gritty plaques with a white luminal surface resembling a coral reef. However, no such case has been described in children.

CASE PRESENTATION

We present an adolescent boy who presented with a heavily calcified ascending aortic lesion associated with aortopathy and hypertension, 12 years after an aortic coarctation repair. The investigations included echocardiography, magnetic resonance and computer-tomographic imaging. A 3-D model was printed in order to visualize and plan surgical steps in advance for safe placement of clamps and defining the extent of resection. In addition, it provided an idea about tissue quality, thickness, spatial relationship, and orientation in relation to surrounding structures. Successful resection and replacement of the diseased segment of the aorta were achieved on cardiopulmonary bypass support. Post-operative recovery was uneventful, and at 6-month follow-up, the patient is doing well. In this report, various aspects of such lesions have been discussed, including clinical presentations, complications, planning and conduct of a safe cardiopulmonary bypass, and precautions during surgery for a successful outcome.

CONCLUSION

Complicated obstructive aortic lesions in children require careful assessment, appropriate advanced imaging, and the use of 3-D printing technology in order to plan and perform safe and effective surgical management. The etiology of severe calcified aorta in children may be related to metabolic factors, previous surgery, use of a homograft, or an inflammatory process. However, it has yet to be proven.

The changing face of surgical education: transfer of surgical and endovascular knowledge to young surgeons

The goal of vascular surgery education is to provide the best possible training to vascular residents and fellows and to assure the highest standards of care for patients with vascular disease. In the USA, the currently used Vascular Surgery Milestones Program includes milestones as set targets at five levels, from novice to expertise, to assess the trainees' performance in knowledge, skills, attitudes, and other attributes of competencies. Competencies are broad and foundational domains of ability, the most important being the care of the patient. The soon to be introduced Entrustable Professional Activities (EPA) Project, a competency-based assessment, appears to be the best way to evaluate that trainees are ready to practice independently. Transferring surgical and endovascular skills to trainees has been, however, a challenge, because of the decreased number of open surgical procedures, the increasing number of the endovascular interventions, the decreased work hours for residents and that learning on patients in the operating room is no longer acceptable. Simulation laboratories, using 3D reconstructions of real patient's aneurysms has been most helpful to teach even complex endovascular procedures. In open or endovascular simulation laboratories, deliberate practice with focused attention and specific goals of improving performance should be combined with expert feedback. Greatness is not coded into our DNA but comes from deliberate practice, dedication and perseverance.