A compact Class D RF power amplifier for mobile nuclear magnetic resonance systems

A pulsed current-mode class-D low-voltage high-bandwidth power amplifier for portable NMR systems

Low-field NMR has seen growing interest in recent years, especially for portable applications. The lower homogeneity magnets used for portable applications require short RF pulses to ensure enough transmit bandwidth to excite the sample volume and also support short echo periods. Furthermore, the preferred use of a high-Q coil to improve signal-to-noise ratio (SNR) prolongs the pulse transients. Thus, at such low Larmor frequencies, the excitation pulse transients become comparable or longer than the pulse length, such that the transmit bandwidth begins to limit measurement SNR. This paper describes the design of a pulsed current-mode class-D power (PCMCD) transmitter that addresses this issue by generating high power in a tuned sample coil while maintaining short transients, thus resulting in high output bandwidth. The transmitter also uses a charge recycling mechanism to maximize power efficiency for RF train excitation, which also results in faster pulse repetition rate and reduces allowable echo time. Experimental results from a small form-factor PCMCD transmitter are presented. This design generates a peak RF power of 240 W into a 9.16 μH coil at 4 MHz while operating off a single 12 V power supply. NMR measurement results using the transmitter are also described, showing minimum achievable echo time of 70 μs and 25 μs depending on the transmitter mode of operation.

Mobile low field magnetic resonance hardware development

Typically, NMR systems are bulky and expensive laboratory based equipment. For half a century after its scientific discovery taking NMR outside of a laboratory environment is still not a common practice due to the complexity of the underlining physical phenomena and its low sensitivity, to the myriad of technical challenges when integrating a complete system. The scarcity of compact and mobile NMR systems has prevented its proliferation into many other areas and applications. This paper describes the progress in the development of compact electronic spectrometers that we coupled with handheld sensors in order to provide complete mobile solutions. The key to this progress has been the modern advances in computing, electronics and permanent magnet technologies. Mobile NMR is now feasible as a valuable, non-invasive tool for industrial and medical applications. By leveraging the strengths of NMR, which is to probe at the molecular level and gain information about molecular structure, organisation, abundance and orientation, NMR is intrinsically suitable for non-destructive testing of a wide range of materials and their manufacturing processes. The development of complete NMR systems benefits from working across various disciplines and organisations. By embracing a collaborative approach we believe it will accelerate NMR technology to become more ubiquitous in the near future.

Three-dimensional MRI in a homogenous 27 cm diameter bore Halbach array magnet

Modern clinical MRI systems utilise very high magnetic fields strengths to produce high resolution images of the human body. The high up-front and maintenance cost of these systems means that much of the world lacks access to this technology. In this paper we propose a low cost, head-only, homogenous Halbach magnet array with the potential for paediatric neuroimaging in low-resource settings. The homogeneity of the Halbach array is improved by allowing the diameter of the Halbach array to vary along its length, and also adding smaller internal shim magnets. The constructed magnet has a bore diameter of 27 cm, mean B₀ field strength of 50.4 mT and a homogeneity of 2400 ppm over a 20 cm diameter spherical volume. The level of homogeneity of the system means that coil-based gradients can be used for spatial encoding which greatly increases the flexibility in image acquisition. 3D images of a "brain phantom" were acquired over a 22 × 22 × 22 cm field of view with a 3.5 mm isotropic resolution using a spin-echo sequence. Future development of a low-cost gradient amplifier and an open-source spectrometer has the potential of offering a fully open-source, low-cost MRI system for paediatric neuroimaging in low-resource settings.

A high duty-cycle, multi-channel, power amplifier for high-resolution radiofrequency encoded magnetic resonance imaging

OBJECTIVE

A radiofrequency (RF) power amplifier is an essential component of any magnetic resonance imaging (MRI) system. Unfortunately, no commercial amplifier exists to fulfill the needs of the transmit array spatial encoding (TRASE) MRI technique, requiring high duty cycle, high RF output power and independently controlled multi-channel capability. Thus, an RF amplifier for TRASE MRI is needed.

MATERIALS AND METHODS

A dual-channel RF power amplifier dedicated for TRASE at 0.22 T (9.27 MHz) was designed and constructed using commercially available components. The amplifier was tested on the bench and used a 0.22 T MRI system with a twisted solenoid and saddle RF coil combination capable of a single-axis TRASE.

RESULTS

The amplifier is capable of sequential, dual-channel operation up to 50% duty cycle, 1 kW peak output and highly stable 100 μs RF pulse trains. High spatial resolution one-dimensional TRASE was obtained with the power amplifier to demonstrate its capability.

CONCLUSION

The constructed amplifier is the first prototype that meets the requirements of TRASE rectifying limitations of duty cycle and timing presented by commercial RF amplifiers. The amplifier makes possible future high resolution in vivo TRASE MRI.