Amperometric Glucose Biosensor Based on the Deposition of Copper and Glucose Oxidase onto Glassy Carbon Transducer

Response surface methodology use in construction of polianiline-coated carbon paste electrode-based biosensor: Modification and characterization

In this study, the effect of amperometric glucose biosensor construction and using conditions on the current response was investigated in detail applying experimental design. Polyaniline (PANI) was synthesized on the carbon paste electrode (CPE) surface using the cyclic voltammetry technique in sodium oxalate (NaOx ) electrolyte medium, and an amperometric biosensor was constructed by immobilizing glucose oxidase (GOD). Biosensor preparation (aniline, GOD and NaOx concentrations, and scan rate) and operating conditions (pH and applied potential) were optimized by Box-Behnken and optimal designs, respectively, via State Ease Design Expert 7.0.1.1 software. ANOVA analyses showed that among the biosensor preparation parameters, the NaOx concentration has the highest effect on the current measured in the presence of glucose, whereas in the optimization of pH and potential parameters applied in current measurement studies, it has been revealed that pH has a very high effect on the measured current. Several compounds, such as MWCNT, two different ionic liquids and two different organic molecules were added to carbon paste, and, among them, 2-cyanoethylpyrrole (CPy) enhanced the efficacy highly, most probably due to its polymerization in the paste and increasing the electron transfer rate of the CPE. Sucrose- and lactose-sensitive biosensors were also constructed by co-immobilizing GOD with invertase (INV) or β-galactosidase, respectively, onto modified CPE, and sensitivities to their substrates were shown by cyclic voltammetry and impedance analysis. CPy modification caused an increase in the current values, and also Imax /KM values increased approximately 11.8, 7.83, and 2.56 times for glucose-, sucrose-, and lactose-sensitive CPEs, respectively.

Copper–Ruthenium Composite as Perspective Material for Bioelectrodes: Laser-Assisted Synthesis, Biocompatibility Study, and an Impedance-Based Cellular Biosensor as Proof of Concept

Copper is an inexpensive material that has found wide application in electronics due to its remarkable electric properties. However, the high toxicity of both copper and copper oxide imposes restrictions on the application of this metal as a material for bioelectronics. One way to increase the biocompatibility of pure copper while keeping its remarkable properties is to use copper-based composites. In the present study, we explored a new copper–ruthenium composite as a potential biocompatible material for bioelectrodes. Sample electrodes were obtained by subsequent laser deposition of copper and ruthenium on glass plates from a solution containing salts of these metals. The fabricated Cu–Ru electrodes exhibit high effective area and their impedance properties can be described by simple R-CPE equivalent circuits that make them perspective for sensing applications. Finally, we designed a simple impedance cell-based biosensor using this material that allows us to distinguish between dead and alive HeLa cells.

3D printed enzymatic microchip for multiplexed electrochemical biosensing

The low-cost e-fabrication of specialized multianalyte biosensors within the point-of-care (POC) settings in a few minutes remains a great challenge. Unlike prefabricated biosensors, 3D printing seems to be able to meet this challenge, empowering the end user with the freedom to create on-demand devices adapted to immediate bioanalytical need. Here, we describe a novel miniature all-3D-printed 4-electrode biochip, capable of the simultaneous determination of different biomarkers in a single assay. The chip is utterly fabricated via an one-step 3D printing process and it is connected to a mini portable bi-potentiostant, permitting simultaneous measurements. The bioanalytical capability of the microchip is demonstrated through the simultaneous amperometric determination of two cardiac biomarkers (cholesterol and choline) in the same blood droplet, via enzymatic assays developed on its two tiny integrated electrodes. The simultaneous determination of cholesterol and choline is free from cross-talk phenomena and interferences offering limits of detection much lower than the cut-off levels of these biomarkers in blood for coronary syndromes. The biodevice is an easy-constructed, low-cost, sensitive and e-transferable POC chip with wide scope of applicability to other enzymatic bioassays.

Implantable Graphene-based Neural Electrode Interfaces for Electrophysiology and Neurochemistry in In Vivo Hyperacute Stroke Model

Implantable microelectrode arrays have attracted considerable interest due to their high temporal and spatial resolution recording of neuronal activity in tissues. We herein presented an implantable multichannel neural probe with multiple real-time monitoring of neural-chemical and neural-electrical signals by a nonenzymatic neural-chemical interface, which was designed by creating the newly developed reduced graphene oxide-gold oxide (rGO/Au2O3) nanocomposite electrode. The modified electrode on the neural probe was prepared by a facile one-step cyclic voltammetry (CV) electrochemical method with simultaneous occurrence of gold oxidation and GOs reduction to induce the intimate attachment by electrostatic interaction using chloride ions (Cl(-)). The rGO/Au2O3-modified electrode at a low deposition scan rate of 10 mVs(-1) displayed significantly improved electrocatalytic activity due to large active areas and well-dispersive attached rGO sheets. The in vitro amperometric response to H2O2 demonstrated a fast response of less than 5 s and a very low detection limit of 0.63 μM. In in vivo hyperacute stroke model, the concentration of H2O2 was measured as 100.48 ± 4.52 μM for rGO/Au2O3 electrode within 1 h photothrombotic stroke, which was much higher than that (71.92 μM ± 2.52 μM) for noncoated electrode via in vitro calibration. Simultaneously, the somatosensory-evoked potentials (SSEPs) test provided reliable and precise validation for detecting functional changes of neuronal activities. This newly developed implantable probe with localized rGO/Au2O3 nanocomposite electrode can serve as a rapid and reliable sensing platform for practical H2O2 detection in the brain or for other neural-chemical molecules in vivo.

Recent advances in electrochemical sensing for hydrogen peroxide: a review

Due to the significance of hydrogen peroxide (H(2)O(2)) in biological systems and its practical applications, the development of efficient electrochemical H(2)O(2) sensors holds a special attraction for researchers. Various materials such as Prussian blue (PB), heme proteins, carbon nanotubes (CNTs) and transition metals have been applied to the construction of H(2)O(2) sensors. In this article, the electrocatalytic H(2)O(2) determinations are mainly focused on because they can provide a superior sensing performance over non-electrocatalytic ones. The synergetic effect between nanotechnology and electrochemical H(2)O(2) determination is also highlighted in various aspects. In addition, some recent progress for in vivo H(2)O(2) measurements is also presented. Finally, the future prospects for more efficient H(2)O(2) sensing are discussed.

Amperometric glucose biosensor based on assisted ion transfer through gel-supported microinterfaces

A novel amperometric glucose sensor was developed based on the facilitated proton transfer across microinterfaces between two immiscible electrolyte solutions. The combination of a 1,3:2,4-dibenzylidene sorbitol/2-nitrophenyl octyl ether gel membrane and 3-(2-pyridyl)-5,6-diphenyl-1,2,4-triazine as the ionophore allows the transfer of protons from water to the gellified organic phase; the gel membrane is supported on arrays of microholes drilled on a polyester film. The protons are generated as the result of the dissociation of gluconic acid produced during the enzymatic degradation of glucose by glucose oxidase. The characteristics of the glucose sensor were investigated using several experimental conditions, namely, the concentration of ligand and enzyme. The electrochemical response is typical of an enzymatic electrode and displays a linear behavior in the range 0.2-3 mM glucose. The effect of the experimental parameters of the voltammetric technique was also optimized with the aim of improving sensor sensitivity.