Evaluation of the fouling potential of ceramic membrane configurations designed for the treatment of oilfield produced water

Enhancing oil-water emulsion separation via synergistic filtration using graphene oxide-silver oxide nanocomposite-embedded polyethersulfone membrane

This study introduces an innovative approach for enhancing oil-water emulsion separation using a polyethersulfone (PES) membrane embedded with a nanocomposite of graphene oxide (GO) and silver oxide (AgO). The composite membrane, incorporating PES and polyvinyl chloride (PVC), demonstrates improved hydrophilicity, structural integrity and resistance to fouling. Physicochemical characterization confirms successful integration of GO and AgO, leading to increased tensile strength, porosity and hydrophilicity. Filtration tests reveal substantial improvements in separating various oils from contaminated wastewater, with the composite membrane exhibiting superior efficiency and reusability compared to pristine PES membranes. This research contributes to the development of environmentally friendly oil-water separation methods with broad industrial applications.

High-Performance γ-Al2O3 Multichannel Tube-Type Tight Ultrafiltration Membrane Using a Modified Sol-Gel Method

We introduced a modified sol-gel method using polyvinyl alcohol (PVA) as an additive to improve the permeability of γ-Al₂O₃ membranes by minimizing the thickness of the selective layer and maximizing the porosity. First, the analysis revealed that the thickness of γ-Al₂O₃ decreased as the concentration of PVA increased in the boehmite sol. Second, the properties of the γ-Al₂O₃ mesoporous membranes were greatly influenced by the modified route (method B) compared to the conventional route (method A). The results showed that the porosity and surface area of the γ-Al₂O₃ membrane increased, and the tortuosity decreased considerably using method B. This effect was attributed to the adsorption of PVA molecules on the surface of the boehmite particles, which depended on the synthesis route. The experimentally determined pure water permeability trend and the Hagen-Poiseuille mathematical model confirmed that the modified method improved the performance of the γ-Al₂O₃ membrane. Finally, the γ-Al₂O₃ membrane fabricated via a modified sol-gel method with a pore size of 2.7 nm (MWCO = 5300 Da) exhibited a pure water permeability of over 18 LMH/bar, which is three times higher than that of the γ-Al₂O₃ membrane prepared using the conventional method.

Experimental Investigation of the Novel Periodic Feed Pressure Technique in Minimizing Fouling during the Filtration of Oily Water Systems Using Ceramic Membranes

Fouling represents a bottleneck problem for promoting the use of membranes in filtration and separation applications. It becomes even more persistent when it comes to the filtration of fluid emulsions. In this case, a gel-like layer that combines droplets, impurities, salts, and other materials form at the membrane's surface, blocking its pores. It is, therefore, a privilege to combat fouling by minimizing the accumulation of these droplets that work as seeds for other incoming droplets to cluster and coalesce with. In this work, we explore the use of the newly developed and novel periodic feed pressure technique (PFPT) in combating the fouling of ceramic membranes upon the filtration of oily water systems. The PFPT is based on alternating the applied transmembrane pressure (TMP) between the operating one and zero. A PFPT cycle is composed of a filtration half-cycle and a cleaning half-cycle. Permeation occurs when the TMP is set at its working value, while the cleaning occurs when it is zero. Three PFPT patterns were examined over two feeds of oily water systems with oil contents of 100 and 200 ppm, respectively. The results show that the PFPT is very effective in minimizing the problem of fouling compared to a non-PFPT normal filtration. Furthermore, the overall drops in permeate flux during the cleaning half-cycles are compensated by appreciable enhancement due to the significant elimination of fouling development such that the overall production of filtered water is even increased. Inspection of the internal surface of the membrane post rinsing at the end of the experiment proves that all PFPT cycles maintained the ceramic membranes as clean after a 2-h operation. This can ensure a prolonged lifespan of the ceramic membrane use and a continuous greater permeate volume production. The advantage of the PFPT is that it can be implemented on existing units with minimal modification, ease of operation, and saving energy.

Oilfield-produced water treatment using conventional and membrane-based technologies for beneficial reuse: A critical review

Oilfield produced water (OPW) is one of the most important by-products, resulting from oil and gas exploration. The water contains a complex mixture of organic and inorganic compounds such as grease, dissolved salt, heavy metals as well as dissolved and dispersed oils, which can be toxic to the environment and public health. This article critically reviews the complex properties of OPW and various technologies for its treatment. They include the physico-chemical treatment process, biological treatment process, and physical treatment process. Their technological strengths and bottlenecks as well as strategies to mitigate their bottlenecks are elaborated. A particular focus is placed on membrane technologies. Finally, further research direction, challenges, and perspectives of treatment technologies for OPW are discussed. It is conclusively evident from 262 published studies (1965-2021) that no single treatment method is highly effective for OPW treatment as a stand-alone process however, conventional membrane-based technologies are frequently used for the treatment of OPW with the ultrafiltration (UF) process being the most used for oil rejection form OPW and oily waste water. After membrane treatment, treated effluents of the OPW could be reused for irrigation, habitant and wildlife watering, microalgae production, and livestock watering. Overall, this implies that target pollutants in the OPW samples could be removed efficiently for subsequent use, despite its complex properties. In general, it is however important to note that feed quality, desired quality of effluent, cost-effectiveness, simplicity of process are key determinants in choosing the most suitable treatment process for OPW treatment.

Effect of the Peptization Process and Thermal Treatment on the Sol-Gel Preparation of Mesoporous α-Alumina Membranes

Compared to traditional membrane materials, alumina membranes are particularly beneficial for industrial wastewater treatment. However, the development of mesoporous α-alumina membranes for ultrafiltration applications is still a challenge due to uncontrolled pore size. In this study, we optimized the sol-gel method for the fabrication of a high-performance mesoporous α-alumina membrane. The peptization conditions (pH and peptization time) and phase transformation of boehmite were investigated to achieve better properties of the α-alumina membrane. The surface properties of the membrane were observed to be improved by reducing the system pH to 3.5 and increasing the peptization time to 24 h. The effect of sintering temperature on the phase transformation behavior, microstructures and performance of the membranes was also elucidated. An α-alumina ultrafiltration membrane with an average thickness of 2 μm was obtained after sintering at 1100 °C. The molecular weight cut-off of the α-alumina membrane, as obtained by the filtration of aqueous PEG solution, was approximately 163 kDa (12.5 nm). This is the smallest pore size ever reported for pure α-alumina membranes.

Treatment of oily wastewaters by highly porous whisker-constructed ceramic membranes: Separation performance and fouling models

Efficient treatment of challenging oily emulsion wastewater can alleviate water pollution to provide more chances for water reuse and resource recovery. Despite their promising application potential, conventional porous ceramic membranes have challenging bottleneck issues such as high cost and insufficient permeance. This study presents a new strategy for highly efficient treatment of not only synthetic but real oily emulsions via unexpensive whisker-constructed ceramic membranes, exhibiting exceptional permeance and less energy input. Compared with common ceramic membranes, such lower-cost mullite membranes with a novel whisker-constructed structure show higher porosity and water permeance, and better surface oleophobicity in water. Treatment performance such as permeate flux and oil rejection was explored for the oily emulsions with different properties under key operating parameters. Furthermore, classical Hermia models were used to reveal membrane fouling mechanism to well understand the microscopic interactions between emulsion droplets and membrane interface. Even for real acidic oily wastewater, such membranes also exhibit high permeance and less energy consumption, outperforming most state-of-the-art ceramic membranes. This work provides a new structure concept of highly permeably whisker-constructed porous ceramic membranes that can efficiently enable more water separation applications.

Characterization and treatment of Bakken oilfield produced water as a potential source of value-added elements

The oilfield produced water is a major waste stream in places where shale-gas production is growing rapidly. The reuse of produced water merits consideration because this practice helps reduce freshwater demand for fracking and moderates water pollution. Knowledge about the chemistry of produced water is needed to develop sustainable treatment/reuse strategies and set standards for acceptable levels of treatment of produced water. Thus, the author performed the first comprehensive analysis of oilfield produced water collected from the Bakken shale play in the U.S. state of North Dakota that represents the nation's third-largest net increase in proven crude oil reserves. The concentrations of a total of 36 elements in 13 IUPAC groups were determined. Among them, a few metals that are critical to the economy of the United States were detected at elevated concentrations (median, mg/L): K (7,620), Mg (2780), Sr (1610), Li (69), and Mn (33). Heavy metals essential for plants and animals, including Cu, Zn, and Mn, were detected at ppm levels. Measurable concentrations of highly toxic metal ions such as Cd and Pb were not detected. Concentrations of rare earth elements and platinum group metals were below respective detection limits. The produced water samples had very high total dissolved solids (237,680 ± 73,828 mg/L) and total hardness (>31,000 mg/L as CaCO₃) but an extremely low alkalinity (152.4 ± 184.9 mg/L as CaCO₃); therefore, softening by lime and soda was ineffective. Softening by caustic soda removed 99.5% hardness ions (Ca and Mg) under alkaline conditions. This study provides vital insight into the chemistry and treatability of produced water containing various metals.

Innovative Optical-Sensing Technology for the Online Fouling Characterization of Silicon Carbide Membranes during the Treatment of Oily Water

The oil and gas industry generates a large volume of contaminated water (produced water) which must be processed to recover oil before discharge. Here, we evaluated the performance and fouling behavior of commercial ceramic silicon carbide membranes in the treatment of oily wastewaters. In this context, microfiltration and ultrafiltration ceramic membranes were used for the separation of oil during the treatment of tank dewatering produced water and oily model solutions, respectively. We also tested a new online oil-in-water sensor (OMD-32) based on the principle of light scattering for the continuous measurement of oil concentrations in order to optimize the main filtration process parameters that determine membrane performance: the transmembrane pressure and cross-flow velocity. Using the OMD-32 sensor, the oil content of the feed, concentrate and permeate streams was measured continuously and fell within the range 0.0-200 parts per million (ppm) with a resolution of 1.0 ppm. The ceramic membranes achieved an oil-recovery efficiency of up to 98% with less than 1.0 ppm residual oil in the permeate stream, meeting environmental regulations for discharge in most areas.

Treatment of petrochemical wastewater and produced water from oil and gas

Wastewater in petrochemical processes and produced water from oil and gas production remain a challenge for the industry to minimize their impact on the environment. Recent research and development of treatment technologies for petrochemical wastewater and produced water from oil and gas industries published in 2018 were summarized in this annual review. Great efforts and progresses were made in various treatment options, including membrane processes, advanced oxidation, biological systems, adsorption, coagulation, and combined processes. PRACTITIONER POINTS: Treatment technologies for petrochemical wastewater are reviewed. Research development in produced water from oil and gas industries is summarized. Reviewed technologies include traditional, advanced, and innovative processes.