Investigation of alternative compounds to poly(E-MA) as a polymeric surfactant for preparation of microcapsules by phase separation method

The Microencapsulation of Tung Oil with a Natural Hydrocolloid Emulsifier for Extrinsic Self-Healing Applications

In this work, tung oil was utilised as a catalyst-free self-healing agent, and an in-situ polymerization process was applied to encapsulate the tung oil core with a poly(urea-formaldehyde) (PUF) shell. The conventional poly(ethylene-alt-maleic-anhydride) (PEMA) polymer was compared to a more naturally abundant gelatin (GEL) emulsifier to compare the microcapsules’ barrier, morphological, thermal, and chemical properties, and the crystalline nature of the shell material. GEL emulsifiers produced microcapsules with a higher payload (96.5%), yield (28.9%), and encapsulation efficiency (61.7%) compared to PEMA (90.8%, 28.6% and 52.6%, respectively). Optical and electron microscopy imaging indicated a more uniform morphology for the GEL samples. The thermal decomposition measurements indicated that GEL decomposed to a value 7% lower than that of PEMA, which was suggested to be attributed to the much thinner shell materials that the GEL samples produced. An innovative and novel focused ion beam (FIB) milling method was exerted on the GEL sample, confirming the storage and release of the active tung oil material upon rupturing. The samples with GEL conveyed a higher healing efficiency of 91%, compared to PEMA’s 63%, and the GEL samples also conveyed higher levels of corrosion resistance.

Improved volatile cargo retention and mechanical properties of capsules via sediment-free in situ polymerization with cross-linked poly(vinyl alcohol) as an emulsifier

HYPOTHESIS

It is hypothesized that poly(vinyl alcohol) (PVOH) as an emulsifier destabilizes the insoluble molecular aggregates by increasing interparticle interactions and their tendency toward agglomeration into large particle aggregates during the encapsulation process of one-step in situ polymerization. Porosity of capsule shells is expected to decrease with reducing agglomeration tendency to allow dense packing of smaller insoluble aggregates. Cross-linking the polymer network further reduces shell permeability to improve the retention of volatile cargos. PVOH also modifies the short-range order of polymer network to bestow improved mechanical properties in addition to the shell thickening effect at appropriate synthesis conditions.

EXPERIMENTS

PVOH was used to stabilize a heptane-in-water emulsion as a template for producing capsules via one-step in situ polymerization. Shell morphologies at different PVOH concentrations were compared. Physical freeze-thawing and chemical cross-linking were adopted separately to synthesize capsules with a volatile cargo, and its retention was characterized qualitatively by a solvatochromism-based fluorescent method and quantitative payload calculation. Mechanical properties of capsules were tested with micromanipulation. The effect of graphene oxide (GO) impregnation into capsules was studied with various co-emulsifiers.

FINDINGS

When PVOH alone was used as the emulsifier for capsule synthesis, the higher its concentration, the more porous the shell structure was. At very low concentrations, visible pores were eliminated. Freeze-thaw cycles reduced the permeability of capsule shells when visible pores were absent. Chemical cross-linking with poly(acrylic acid) (PAA) significantly improved the retention of volatile cargo heptane. PVOH substantially reduced polymer sediment during capsule synthesis, which eliminated the tedious centrifugation procedure that normally would have followed. Superior mechanical strength of capsules was achieved with PAA cross-linked PVOH at appropriate conditions. The impregnation of aqueously dispersed GO into capsules was also promoted by using PVOH but not hydrocolloid emulsifiers.

Self-assembly of poly(o-methoxyaniline) hollow nanospheres from a polymeric acid solution

Self-assembled poly(o-methoxyaniline) (POMA) hollow nanospheres were prepared in a solution of poly(methyl vinyl ether-alt-maleic acid) (PMVEA) by oxidative polymerization using ammonium persulfate as the oxidant. The weight ratio of PMVEA to o-methoxyaniline in the solution had a significant effect on the morphology of the poly(o-methoxyaniline) nanospheres as determined by scanning electron microscopy. The diameter of the hollow nanospheres decreased from 440 to 210 nm with an increase in the PMVEA concentration from 1% to 5%. Freeze-fracture transmission electron microscopy results showed the presence of spherical micelles composed of PMVEA/ o-methoxyaniline prior to polymerization, which also decreased in size as more PMVEA was added to the solution, and can act as soft templates for the formation of the hollow POMA nanospheres. The POMA/PMVEA hollow nanospheres were characterized by means of Fourier transform infrared, UV-visible, x-ray photoelectron spectroscopy, elemental analysis and conductivity measurements.

Microcapsules with macroholes prepared by the competitive adsorption of surfactants on emulsion droplet surfaces

We demonstrate a simple, unique method for preparing microcapsules with holes in their shells. Cross-linked polymelamine microcapsules are prepared by the phase-separation method. The holey shell of each microcapsule is synthesized on the surface of an oil-in-water (O/W) emulsion droplet where a water-soluble polymeric surfactant and an oil-soluble surfactant are competitively adsorbed. The water-soluble polymeric surfactant provides a reaction site for shell formation. The oil-soluble surfactant molecules seem to self-assemble while the shells are being formed, so holes appear where they assemble. The critical degree of surface coverage of an emulsion droplet by the water-soluble polymeric surfactant needed to form the holey shells is determined to be 0.90 from theoretical calculations in which competitive adsorption is considered. Theoretical consideration suggests that the size and quantity of the holes in the microcapsule shells are controlled by the composition of the surfactants adsorbed on the surface of an emulsion droplet. This theoretical consideration is confirmed by experiments. The prepared microcapsule with controllable macroholes in its shell has the potential to be used for controlled release applications and can be used to fabricate a microcapsule that encapsulates hydrophilic compounds.

Micro/nanostructured polymeric systems for biomedical and pharmaceutical applications

This review provides an outline of the polymeric micro/nanostructured advanced systems that are suited for the controlled and targeted administration of, specifically, nonconventional drugs. The contribution of new trends in drug-delivery technology is focused on two major parts, dealing with brief surveys of: the biodegradable/bioerodible polymeric systems used in the formulation of micro/nanoparticles and techniques used in the preparation of micro/nanoparticles for their biomedical application in cancer treatment specifically, in inflammation pathologies, as oxygen carriers (blood substitutes) and in tissue-engineering practice. A small discussion of the future perspectives of the described systems is also given.