Employing magnetism of Fe3O4 and hydrophilicity of ZrO2 to mitigate biofouling in magnetic MBR by Fe3O4-coated ZrO2/PAN nanocomposite membrane

Modeling and simulation-assisted strategies for effective membrane-fouling mitigation during membrane bioreactor operation

This research principally aimed to present a suitable strategy for membrane-fouling mitigation in membrane-bioreactors (MBRs). The current strategies for membrane-fouling mitigation before initiating the process in many cases, are unmodifiable for a specific MBR system along the operations. Thus, membrane-fouling strategies during filtration should be applied. To select the best and most economical method for controlling fouling during the operations, the quality (site and mechanism) as well as quantity (thickness, mass, and porosity of the cake layer, and pore resistances) of fouling should be predicted. Accordingly, in this research, two powerful tools, i.e. modeling and simulation, have been used for predicting the quality and quantity of fouling, respectively. Through modeling, the best model describing the site and mechanism of fouling was chosen. Through simulation, the thickness, mass and porosity of the cake layer, along with resistance of cake and pores were calculated. In addition, the match between the results of modeling, simulation, and experimental results confirmed the accuracy of the performed predictions. Ultimately, to achieve the minimum membrane-fouling during filtration, based on the modeling results, the general solution of washing (physical or chemical), and based on the simulation results, its intensity (low, medium, and high) were proposed.

Membrane processes enhanced by various forms of physical energy: A systematic review on mechanisms, implementation, application and energy efficiency

Membrane technologies in water and wastewater treatment have been eagerly pursued over the past decades, yet membrane fouling remains the major bottleneck to overcome. Membrane fouling control methods which couple membrane processes with online in situ application of external physical energy input (EPEI) are getting closer and closer to reality, thanks to recent advances in novel materials and energy deliverance methods. In this review, we summarized recent studies on membrane fouling control techniques that depend on (i) electric field, (ii) acoustic field, (iii) magnetic field, and (iv) photo-irradiation (mostly ultraviolet or visible light). Mechanisms of each energy input were first reported, which defines the applicability of these methods to certain wastewater matrices. Then, means of implementation were discussed to evaluate the compatibility of these fouling control methods with established membrane techniques. After that, preferred applications of each energy input to different foulant types and membrane processes in the experiment reports were summarized, along with a discussion on the trends and knowledge gaps of such fouling control research. Next, specific energy consumption in membrane fouling control and flux enhancement was estimated and compared, based on the experimental results reported in the literature. Lastly, strength and weakness of these methods and future perspectives were presented as open questions.

Nanomaterials in membrane bioreactors: Recent progresses, challenges, and potentials

The use of nanomaterials (NMs) in the fabrication and modification of membranes as well as the coupling of nanomaterial-based processes with membrane processes have been attracted many researchers today. The NMs due to a wide range of types, different chemistry, the possibility of various kinds of functionality, different properties like antibacterial activity, hydrophilicity, and large surface area were applied to enhance the membrane properties. In the membrane bioreactors (MBRs) as a highly successful process of membrane technology in wastewater treatment, the NMs have been applied for improving the efficiency of MBR process. This review assessed the application of NMs both as the modifiers of membrane and as the effective part of hybrid techniques with MBR system for wastewater treatment. The efficiency of NMs blended membranes in the MBR process has been reviewed in terms of antifouling and antibacterial improvement and removal performance of the pollutants. Novel kinds of NMs were recognized and discussed based on their properties and advantages. The NMs-based photocatalytic and electrochemical processes integrated with MBR were reviewed with their benefits and drawbacks. In addition, the effect of the presence of mobilized NPs in the sludge on MBR performance was surveyed. As a result of this review, it can be concluded that nanomaterials generally improve MBR performance. The high flux and antifouling properties can be obtained by adding nanomaterials with hydrophilic and antibacterial properties to the membrane, and further studies are required for photocatalytic NMs applications. In addition, this review shows that the low amounts of NMs in the membrane structure could have an effective influence on the MBR process. Besides, since many studies in the literature are carried out at the laboratory scale, it is thought that pilot and real-scale studies should be carried out to obtain more reliable data.

Influence of alumina nanoparticles on the performance of polyacrylonitrile membranes in MBR

This study aims to investigate the effect of using Al₂O₃ nanoparticles (NPs) in membrane structure on the operation condition of the membrane bioreactor. To this end, alumina NPs as the high hydrophilic agents with an approximate size of 40 nm and a concentration of 0-3 wt.% were placed within the PAN polymeric membrane matrix structure with high hydrophilicity and high mechanical resistance over the others via the phase inversion method. Characterization of synthesized nanocomposite membranes was carried out by SEM analysis. In the presence of the alumina NPs, the porosity of the membranes improved. The water contact angle measurement confirmed the superior hydrophilicity of mixed PAN membranes compared to the pure polymeric membranes. The best nanocomposite membrane with better antifouling properties was selected to evaluate the MBR's performance in wastewater treatment and assessed in terms of the resistance, flux recovery, and COD removal rates. The result of a comparison with pure membrane showed that by increasing the Al₂O₃ amount up to 2wt.%, irreversible fouling resistance mitigated as much as 50%. Moreover, the flux recovery ratio was increased by 15%, and the COD removal rate was also raised as large as 16%. Our investigation illustrated that the presence of alumina NPs has improved the MBR performance and decreased the irreversible fouling resistance of the membrane.

Modification of polyethersulfone membranes by Polyethyleneimine (PEI) grafted Silica nanoparticles and their application for textile wastewater treatment

In the current work, a novel nanocomposite membrane for wastewater treatment applications has been synthesized. A hydrophilic nature nanoadditive comprised grafting polyethylenimine (PEI) molecules onto the surfaces of silica nanoparticles (SiO₂ NPs) was synthesized then entrapped within a polyethersulfone polymeric matrix at disparate ratios via the classical phase inversion technique. A series of experimental tools were employed to probe the influence of SiO₂-PEI on the surface topography and morphological changes, hydrophilicity, porosity, surface chemistry as well as permeation and dyes retention characteristics of the new nanocomposite. Upon increasing the nanoadditives content (up to 0.7 wt. % SiO₂- PEI), clear cross-sectional changes were depicted along with a noticeable decline in the water contact angle by 29.7%. Performance evaluation measurements against synthetic dye solutions were disclosed explicit enhancement in both; retention and permeation characteristics of the nanocomposite membranes. Besides, prolonged permeation test has maintained high flux stability against real textile wastewater; implying better resistance and self-cleaning characteristics have been achieved.

Magnetic MBR technology: from the fabrication of membrane to application in wastewater treatment

The aim of this study is to synthesize a magnetic nanocomposite membrane using iron oxide and alumina nanoparticles and employing it in magnetic membrane bioreactors (MBRs) for oily wastewater treatment. Al₂O₃ and Fe₃O₄ nanoparticles with approximate sizes of 20 and 30 nm respectively, were settled into a polysulfone (PSf) membrane matrix via magnetic casting method. The concentration of alumina and iron oxide nanoparticles were 0-0.25 wt% and 0.03 wt%, respectively. Compared with the blank membrane, an increase in the concentration of Fe₃O₄ up to 0.2 wt%, led to the flux as much as 70% and mitigated total resistance by 70%. The presence of the magnetic field around the bioreactor increased the flux significantly and reduced the cake resistance by 93%. Moreover, by applying the static magnetic field to MBR, the Chemical Oxygen Demand (COD) removal rate was increased to 93%, while in the MBR without the magnetic field the COD removal rate was 80%. Our investigation illustrated that the magnetic casting is an effective method to improve the flux and mitigate the fouling of the magnetic nanocomposite membrane. The output of this research indicates that the magnetic casting method enhance the magnetic MBRs performance for wastewater treatment.

Application of zinc oxide and sodium alginate for biofouling mitigation in a membrane bioreactor treating urban wastewater

This research aimed to mitigate fouling in membrane bioreactors (MBR) through concurrent usage of zinc oxide as an antibacterial agent (A) and sodium alginate as a hydrophilic agent (H) within a polyacrylonitrile membrane (PM) structure. The antibacterial polymeric membranes (APM) and antibacterial hydrophilic polymeric membranes (AHPM) synthesized showed a higher porosity, mechanical strength and bacterial inhibition zone, and a lower contact angle in comparison with PM membranes. EDS, SEM and AFM analyses were used to characterize the chemical, structural, and morphological properties of PM, APM, and AHPM. The flux of PM, APM, and AHPM in MBR was 37, 48, and 51 l m^-2 h^-1 and COD removal was 81, 93.5, and 96.7%, respectively. After MBR operation for 35 days in an urban wastewater treatment, only 50% of the flux of PM was recovered, while the antibacterial and hydrophilic agents yielded a flux recovery of 72.7 and 100% for APM and AHPM, respectively.