Fracture load of colored and non-colored high translucent zirconia three-unit fixed dental prosthesis frameworks

Influence of coloring liquid immersion on flexural strength, Vickers hardness, and color of zirconia

STATEMENT OF PROBLEM

Zirconia is a widely used restorative material, yet its white color does not meet esthetic requirements and coloring is needed. However, the effects of different durations of coloring have not been thoroughly investigated.

PURPOSE

The purpose of this in vitro study was to evaluate the effects of coloring liquid immersion of different durations on the flexural strength, Vickers hardness, and color of zirconia.

MATERIAL AND METHODS

Fifty bar-shaped and 60 disk-shaped zirconia specimens were milled from nonshaded (Copran Zri) and preshaded (Copran Zri Precoloured Medium) disks by using a computer-aided design and computer-aided manufacturing (CAD-CAM) system. Preshaded specimens were assigned to the group PS and received no further immersion. Nonshaded specimens were divided into 4 subgroups as per immersion time in coloring liquid (Copran Color A2 Shade): control (C; no immersion), G45 (45 seconds of immersion), G90 (90 seconds of immersion), and G135 (135 seconds of immersion). Bar-shaped specimens were subjected to a 3-point flexural strength test by using a universal testing machine (Lloyd LRX), following the International Organization for Standardization (ISO) 6872:2015 specification. Color coordinates of disk-shaped specimens were measured with a spectrophotometer (VITA Easyshade Advance 4.0) over a gray background. Color differences were calculated by using both CIE76 and CIEDE2000 formulas, followed by a comparison of obtained values with perceptibility (CIE76: 3.7, CIEDE2000: 0.8) and acceptability (CIE76: 6.8, CIEDE2000: 1.8) thresholds of each formula. Subsequently, Vickers hardness measurements were conducted. The data were statistically analyzed by using the Shapiro-Wilk test, 1-way ANOVA, and the Tukey HSD test (α=.05).

RESULTS

Immersing zirconia specimens in coloring liquid decreased the flexural strength and hardness values, as group C presented the highest values for both parameters. In addition, prolonged duration had a negative effect on mechanical properties. The flexural strength of groups PS and G45 (P=.993) and groups G90 and G135 (P=.999) was statistically similar. For Vickers hardness, group G135 presented the lowest values with the difference between groups G90 and G135 being statistically similar (P=.061). Color differences among groups varied from 2.49 to 27.33 for ΔE∗, whereas ΔE₀₀ values ranged from 0.58 to 8.26. Compared with group C, ΔE∗ values of all shaded specimens exceeded the acceptability threshold of 6.8. The color difference between each group was higher than the acceptability threshold values of both ΔE∗ and ΔE₀₀ except for groups G45 and PS.

CONCLUSIONS

Colored zirconia specimens had lower flexural strength and Vickers hardness values than nonshaded specimens, regardless of the immersion time or coloring technique.

Effect of extrinsic pigmentation and surface treatments on biaxial flexure strength after cyclic loading of a translucent ZrO2 ceramic

OBJECTIVE

To evaluate the influence of extrinsic pigmentation on the biaxial flexural strength and surface topographic of translucent Y-TZP (InCoris TZI - Sirona - USA) subjected to several surface treatments.

METHODS

Sintered zirconia discs-shaped specimens (n=120) (ø:12mm; thickness:1.2mm; ISO 6872) were prepared and divided (n=15) according to various factors: "extrinsic pigmentation" (n: without; p: with) and "surface treatments" (C: control - as sintered; A: abraded with silica-coated alumina particles (30μm); G: glazed with a thin film of low-fusing porcelain glaze; GH: glazed and etched with 10% hydrofluoridric acid for 60s. Mechanical cycling (1.2×106 cycles, 200N, 3.8Hz) and flexural strength test (1mm/min - 1000kg cell) were performed. Two-way ANOVA and Tukey's were used for statistical test (α=0.05). Weibull analysis was used to evaluate the strength reliability. Samples were analyzed via (1) an optical profilometer to determine the surface roughness (Ra); (2) an X-ray diffraction (XRD) to evaluate phase transformations; and (3) a SEM equipped with an energy dispersive X-ray spectroscopy (EDX) to elucidate morphological properties and chemical compositions.

RESULTS

Regardless of the surface treatment (p=0.5459) (Cn: 560.16MPa; Gn: 573.36MPa; An: 643.51MPa; GHn: 542.94MPa; Cp: 628.04MPa; Gp: 641.90MPa; Ap: 554.47MPa; GHp :602.84MPa) and extrinsic pigmentation (p=0.1280) there was no difference in the flexural strength among the experimental groups. According to the XRD analysis, phase transformations occurred in the An group (t→m) and in Ap group (t→c). Surface roughness was affected by surface treatments (An - p=0.001) and extrinsic pigmentation (Gp - p=0.001).

SIGNIFICANCE

The biaxial flexural strength of the tested samples was not affected neither by surface treatments nor by pigmentation, although it can cause phase transformation and promote surface roughness.