Three-dimensional free-standing carbon nanotubes for a flexible lithium-ion battery anode

Flexible Li[Li0.2Ni0.13Co0.13Mn0.54]O2/Carbon Nanotubes/Nanofibrillated Celluloses Composite Electrode for High-Performance Lithium-Ion Battery

Rapidly-growing demand for wearable and flexible devices is boosting the development of flexible lithium ion batteries (LIBs). The exploitation of flexible electrodes with high mechanical properties and superior electrochemical performances has been a key challenge for the rapid practical application of flexible LIBs. Herein, a flexible composite electrode was prepared from the mixed solutions of Li[Li_0.2Ni_0.13Co_0.13Mn_0.54]O₂ (LLOs), carbon nanotubes(CNTs), and nanofibrillated celluloses (NFCs) via a vacuum filtration method. The resulting LLOs/CNTs/NFCs electrode delivered an initial discharge capacity of 253 mAh g⁻¹ at 0.1 C in the voltage range from 2.0 to 4.6 V, and retained a reversible capacity of 178 mAh g⁻¹ with 83% capacity retention after 100 cycles at 1 C. The LLOs/CNTs/NFCs electrode exhibited excellent flexibility along with repeated bending in the bending test. The LLOs/CNTs/NFCs electrode after bending test remained a discharge capacity of 149 mAh g⁻¹ after 100 cycles at 1 C, and the corresponding capacity retentions was 76%. The excellent electrochemical performance and high flexibility can be ascribed to the framework formed by CNTs with high conductivity and NFCs with good mechanical properties. The results imply that the as-fabricated electrode can be a promising candidate for the flexible LIBs.

In situ fabrication of a graphene-coated three-dimensional nickel oxide anode for high-capacity lithium-ion batteries

The high theoretical specific capacity of nickel oxide (NiO) makes it attractive as a high-efficiency electrode material for electrochemical energy storage. However, its application is limited due to its inferior electrochemical performance and complicated electrode fabrication process. Here, we developed an in situ fabrication of a graphene-coated, three-dimensional (3D) NiO–Ni structure by simple chemical vapor deposition (CVD). We synthesized NiO layers on Ni foam through a thermal oxidation process; subsequently, we grew graphene layers directly on the surface of NiO after a hydrogen-assisted reduction process. The uniform graphene coating renders high electrical conductivity, structural flexibility and high elastic modulus at atomic thickness. The graphene-coated 3D NiO–Ni structure delivered a high areal density of ∼23 mg cm⁻². It also exhibits a high areal capacity of 1.2 mA h cm⁻² at 0.1 mA cm⁻² for its Li-ion battery performance. The high capacity is attributed to the high surface area of the 3D structure and the unique properties of the graphene layers on the NiO anode. Since the entire process is carried out in one CVD system, the fabrication of such a graphene-coated 3D NiO–Ni anode is simple and scalable for practical applications.

The processing of graphene coated NiO–Ni anode using one CVD system delivered high Li-ion battery performance.

Polysiloxane Functionalized Carbon Dots and Their Cross-Linked Flexible Silicone Rubbers for Color Conversion and Encapsulation of White LEDs

In this work, aminopropylmethylpolysiloxane (AMS) functionalized luminescent carbon dots (AMS-CDs) were prepared via a one-step solvothermal method. AMS-CDs could be self- or co-cross-linking with AMS to form 3D flexible transparent silicone rubbers (SRs) where CDs acted as cross-linking points, so the loading fraction of AMS-CDs could be adjusted from 10 to 100 wt %, thus modulating fluorescence properties and flexibility of silicone rubbers. Because of the self-curing property and high thermal stability, AMS-CDs were also studied in white LEDs (WLEDs), serving as a color conversion and encapsulation layer of GaN based blue LEDs simultaneously that would avoid the traditional problem of poor compatibility between emitting and packaging materials. And the color coordinate of AMS-CDs based WLEDs (0.33, 0.28) was very close to the pure white light. In addition, the obtained CDs cross-linked SRs had good transparency (T > 80%) at 510-1400 nm and high refractive indexes (1.33-1.54) that could meet the need of commercial packaging materials and optical application. AMS-CDs were also promising to be used in the UV LEDs based WLEDs according to their wide wavelength emission and flexible optoelectronic device.

Highly porous three-dimensional carbon nanotube foam as a freestanding anode for a lithium-ion battery

Freestanding MWCNT 3D foam demonstrates stable Li-ion storage capacities of 790 mA h g⁻¹ at 0.1C maintaining 99.7% coulombic efficiency.