Nanoscale engineering of ring-mounted nanostructure around AAO nanopores for highly sensitive and reliable SERS substrates

A Rapid, Efficient Method for Anodic Aluminum Oxide Membrane Room-Temperature Multi-Detachment from Commercial 1050 Aluminum Alloy

For commercial processes, through-hole AAO membranes are fabricated from high-purity aluminum by chemical etching. However, this method has the disadvantages of using heavy-metal solutions, creating large amounts of material waste, and leading to an irregular pore structure. Through-hole porous alumina membrane fabrication has been widely investigated due to applications in filters, nanomaterial synthesis, and surface-enhanced Raman scattering. There are several means to obtain freestanding through-hole AAO membranes, but a fast, low-cost, and repetitive process to create complete, high-quality membranes has not yet been established. Here, we propose a rapid and efficient method for the multi-detachment of an AAO membrane at room temperature by integrating the one-time potentiostatic (OTP) method and two-step electrochemical polishing. Economical commercial AA1050 was used instead of traditional high-cost high-purity aluminum for AAO membrane fabrication at 25 °C. The OTP method, which is a single-step process, was applied to achieve a high-quality membrane with unimodal pore distribution and diameters between 35 and 40 nm, maintaining a high consistency over five repetitions. To repeatedly detach the AAO membrane, two-step electrochemical polishing was developed to minimize damage on the AA1050 substrate caused by membrane separation. The mechanism for creating AAO membranes using the OTP method can be divided into three major components, including the Joule heating effect, the dissolution of the barrier layer, and stress effects. The stress is attributed to two factors: bubble formation and the difference in the coefficient of thermal expansion between the AAO membrane and the Al substrate. This highly efficient AAO membrane detachment method will facilitate the rapid production and applications of AAO films.

Fabrication of complexed nanostructure using AAO template for ultrasensitive SERS detection

In the study of surface-enhanced Raman scattering (SERS) processes, a simple and fast approach is needed to ensure the large-scale preparation of SERS substrates. This article uses anodic aluminum oxide (AAO) as a template to assemble gold nanoparticles (Au NPs) into an ordered array. By changing the pore size of AAO and silanizing the pores, the number and density of Au NPs entering the pores through liquid-liquid two-phase self-assembly (LLSA) can be effectively regulated. Using Rh6G (Rhodamine 6G) and CV (Crystal Violet) molecules as probe molecules, substrate sensitivity was evaluated with an enhancement factor of up to 6.34 × 107. In addition, the uniformity of the substrate is good, with a relative standard deviation (RSD) of 9.94%, and the logarithmic concentration and the Raman signal presented significant linear correlations R2 was 0.997 and 0.985, respectively. The detection limit of the substrate for APM (aspartame) as a solvent is as low as 0.0078 g/L. Finally, the substrate was subjected to high sensitivity testing on two types of beverages containing APM sold, proving the practicality of the substrate. It is expected to achieve simple and rapid detection in food additive trace detection in the future.

Electric field-induced assembly of Au-Ag alloy nanoparticles into nano-reticulation for ultrasensitive SERS

This paper discusses a method for assembling Au-Ag alloy nanoparticles (NPs) using direct current (DC) electric field to fabricate highly active SERS substrates. Different nanostructures could be obtained by regulating the intensity and action time of DC electric field. Under the condition of 5mA*10 min, we obtained Au-Ag alloy nano-reticulation (ANR) substrate with excellent SERS activity (Enhancement factor on order of magnitude of 10⁶). ANR substrate has excellent SERS performance due to the resonance matching between its LSPR mode and excitation wavelength. The uniformity of the Raman signal on ANR is greatly improved than bare ITO glass. ANR substrate also has the ability to detect multiple molecules: ANR substrate can respectively detect Rh6G and CV molecules with a concentration as low as 10^-10 M and 10^-9 M and the Raman spectral intensity of the probe molecules on the surface of the ANR substrate has good linear correlation with the molecular concentration (R²> 0.95). In addition, ANR substrate can detect both thiram and aspartame (APM) molecules far below (thiram for 0.0024 ppm and APM for 0.0625 g/L) the safety standard, which demonstrate its practical application potential.

Low-cost and flexible paper-based plasmonic nanostructure for a highly sensitive SERS substrate

The application of a noble-metal-based plasmon-enhanced substrate to detect low-concentration analytes has attracted extensive attention. Most of the substrates used in recently reported researches are based on two-dimensional structures. Hence, we prepared a higher efficiency Raman activity substrate with a filter paper structure, which not only provides more plasmonic "hot spots," but also facilitates analyte extraction and detection due to the flexibility of the paper. The preparation of the plasmonic paper substrate adopted centrifugation to deposit the alloy nanoparticles onto the paper base. The optimal particle deposition condition was found by adjusting the centrifugal force and centrifugation time. Then, the surface-enhanced Raman spectroscopy (SERS) performance of the substrate was enhanced by altering the plasmon resonance peak on the surface of the nanoparticles. The enhancement factor of this paper-based substrate was 1.55×10⁷, with high detection uniformity (10^-6 M, rhodamine 6G) and a low detection limit (10^-11 M, rhodamine 6G). Then, we applied the SERS substrate to pesticide detection; the detection limit of the thiram reached 10^-6 M. As a result, the simple and cost-effective paper-based SERS substrate obtained in this way has high detection performance for pesticides and can be used for rapid detection in the field, which is beneficial to food safety and environmental safety.

Capillary-force-assisted self-assembly of gold nanoparticles into highly ordered plasmonic thin films for ultrasensitive SERS

In this study, a capillary device based on the surface plasmon-enhanced Raman scattering effect was prepared by a simple and easy method. First, the capillary was treated with APTES solution. Due to the electrostatic effect, gold nanoparticles could be easily and tightly assembled in the capillary inner wall. On this basis, the effects of changing the concentration of APTES, the concentration of colloids and the soaking time of the capillary in the colloids on the assembly of gold nanoparticles on the inner wall of the capillary were studied, and the SERS enhancement effect under different conditions was analyzed, and the optimal solution was successfully found. At the same time, the reason why the capillary substrate shows better SERS performance than the traditional planar substrate is deeply discussed. Since the nanoparticles can be attached to the upper and lower surfaces of the inner wall of the capillary, the utilization rate of nanoparticles and laser is improved, thereby achieving higher enhancement. For the detection of the probe molecule rhodamine 6G, it was proved that the substrate has good uniformity and the lowest detection limit can reach 10^-10 M. Finally, the real-life pesticide thiram and the food additive aspartame were tested, and the detection limits could reach 10^-6 M and 0.25 g L^-1. It is confirmed that the prepared capillary shows excellent SERS performance and can be used for rapid detection in various fields.

Nonlinear Optical Microscopy and Plasmon Enhancement

Improving nonlinear optics efficiency is currently one of the hotspots in modern optical research. Moreover, with the maturity of nonlinear optical microscope systems, more and more biology, materials, medicine, and other related disciplines have higher imaging resolution and detection accuracy requirements for nonlinear optical microscope systems. Surface plasmons of metal nanoparticle structures could confine strong localized electromagnetic fields in their vicinity to generate a new electromagnetic mode, which has been widely used in surface-enhanced Raman scattering, surface-enhanced fluorescence, and photocatalysis. In this review, we summarize the mechanism of nonlinear optical effects and surface plasmons and also review some recent work on plasmon-enhanced nonlinear optical effects. In addition, we present some latest applications of nonlinear optical microscopy system research.