Development of broad-band high-reflectivity multilayer film for positron emission tomography system

Colored reflectors to improve coincidence timing resolution of BGO-based time-of-flight PET detectors

Time-of-flight (TOF) positron emission tomography (PET) detectors improve the signal-to-noise ratio of PET images by limiting the position of the generation of two 511 keV gamma-rays in space using the arrival time difference between the two photons. Unfortunately, bismuth germanate (BGO), widely used in conventional PET detectors, was limited as a TOF PET scintillator due to the relatively slow decay time of the scintillation photons. However, prompt Cerenkov light in BGO has been identified in addition to scintillation photons. Using Cerenkov photons for timing has significantly improved the coincidence timing resolution (CTR) of BGO. Based on this, further research on improving the CTR for a BGO-based TOF PET system is being actively conducted. Wrapping materials for BGO pixels have primarily employed white reflectors to most efficiently collect scintillation light. White reflectors have customarily been used as reflectors for BGO pixels even after Cerenkov light began to be utilized for timing calculations in pixel-level experiments. However, when the arrival-time differences of the two 511 keV annihilations photons were measured with pure Cerenkov radiators, painting the lateral sides of the radiators black can improve CTR by suppressing the reflection of Cerenkov photons. The use of BGO for TOF PET detectors requires simultaneously minimizing scintillation loss for good energy information and suppressing reflected Cerenkov photons for better timing performance. Thus, reflectors for BGO pixels should be optimized for better timing and energy performance. In this study, colored polytetrafluoroethylene (PTFE) tapes with discontinuous reflectance values at specific wavelengths were applied as a BGO reflector. We hypothesized that CTR could be enhanced by selectively suppressing reflected Cerenkov photons with an optimum colored reflector on the BGO pixel while minimizing scintillation photon loss. CTRs were investigated utilizing white and three colors (yellow, red, and green) PTFE tapes as a reflector. In addition, black-painted PTFE tape and enhanced specular reflector film were investigated as reference reflector materials. When 3 × 3 × 20 mm3BGO pixels were wrapped with the yellow PTFE reflector, the CTR was significantly improved to 365 ± 5 ps from 403 ± 14 ps measured with the conventional white PTFE reflector. Adequate energy information was still obtained with only 4.1% degradation in light collection compared to the white reflector. Colored reflectors show the possibility to further improve CTR for BGO pixels with optimum reflectance design.

A depth encoding PET detector using four-crystals-to-one-SiPM coupling and light-sharing window method

PURPOSE

Depth of interaction (DOI) decoding capability is of great importance for positron emission tomography (PET) requiring high resolution. In this study, we presented a novel low-cost DOI detector design with four crystals coupling to one SiPM, based on the method of rectangular light-sharing window (RLSW). A prototype detector was constructed, calibrated, and assessed using the methods of homogeneous radiation and flood map analysis.

METHODS

The DOI detector was constructed with a 4 × 4 array of lutetium-yttrium oxyorthosilicate (LYSO) crystals (2.95 mm × 2.95 mm × 20 mm³ ), barium sulfate (BaSO₄ ) reflectors, and optical glues. A RLSW 7 mm in height was deployed in the BaSO₄ reflectors. A non-DOI detector with identical dimensions and without RLSW was also constructed for comparison. The light-output surface of the detector was air-coupled with a 4 × 4 array of SiPMs (3 mm × 3 mm² ). The signals generated from the 16 SiPMs were read out by a custom-designed electronic system, and the signals from four adjacent 3 mm SiPMs were summed into one signal to emulate a 2 × 2 array of 6 mm SiPMs. The RLSW caused the DOI-related position shifts of the crystal spots in the flood map. A homogeneous radiation method was used to establish the transfer functions to convert the spot shifts measured from the flood map into DOI measurements. The accuracy of the DOI measurements was assessed with data acquired using the conventional collimated radiation method.

RESULTS

All 16 crystals are distinctly separated from each other in the flood map. Twelve crystals, including four central crystals and eight edge crystals, have the DOI capability. The full width half maximum (FWHM) of the DOI measurements of the central crystals and the edge crystals are 3.06 ± 0.08 and 3.79 ± 0.15 mm, respectively, for the configuration with four crystals coupling to one SiPM. By contrast, the FWHMs (3.98 ± 0.16 and 5.12 ± 0.38 mm, respectively) are slightly worse for the configuration with one crystal coupling to one SiPM. The average and standard deviation (STD) of the FWHM energy resolutions of the DOI detector and non-DOI detector were 10.2% ± 0.7% and 10.7% ± 1.7%, respectively. Their FWHM coincidence timing resolutions were 197.0 ± 9.6 and 206.4 ± 13.3 ps, respectively. The RLSW had no significant impact on the energy resolutions and timing resolutions of the DOI detector.

CONCLUSIONS

The novel four-crystals-to-one-SiPM coupling technology is a cost-efficient approach to construct high-performance detector modules with DOI capability. The methods of homogeneous radiation and flood map analysis are easy to perform and of good performance. Those methods can be adapted in the clinic PET scanners to enable the capability of DOI measurements.

Ultra-precise surface processing of LYSO scintillator crystals for Positron Emission Tomography

The Lutetium-Yttrium Oxyorthosilicate (LYSO) is one of the most widely used scintillation crystal in the high-performance Positron Emission Tomography (PET) systems. The quality of the surface finish of the LYSO has an important impact on the light output, the decoding performance, the energy resolution and timing resolution of the PET detectors and systems. In this paper, we present an ultra-precise method for processing the surface of LYSO crystals. The hardness and elastic modulus of the crystals were initially measured using Nano indentation technology. The scintillators were fixed onto the plate in sparse, serried and continuous arrangements and polished using an alumina (Al2O3) and cerium oxide (CeO2) polishing solution with particles of varying size. We used a magnetorheological-polishing technique to polish the LYSO crystals. The polishing solution here included hydroxyl iron powder and hard abrasives. The hardness and elastic modulus of the crystals in question was, respectively, 11.18 ± 0.50 and 155.78 ± 4gigapascals (GPa). A 3D optical surface profiler (3D-OPS) and an atomic force microscope (AFM) were used to evaluate the quality of the polished surfaces. The average roughness of Ra 0.55 nm measured by 3D-OPS was achieved using a precise plate grinding and polishing technique. The magnetorheological-polishing method also obtained an excellent roughness of Ra 0.75 nm (3D-OPS). Our report of the use of these processing technologies can serve as a foundation for further in-depth research regarding the optimal techniques for scintillator surface processing.