Relaxation response of lumbar segments undergoing disc-space distraction: implications to the stability of anterior lumbar interbody implants

An OLIF Cage Integrated with a Low-Profile Plate and Cross Screws Could Reduce the Risk of Postoperative Complications Biomechanically

BACKGROUND

Stand-alone oblique lumbar interbody fusion (OLIF) cannot provide credible postoperative stability; additional fixation devices (AFDs) have been used to optimize surgical segment stability. Anterior lateral single rod (ALSR) screw fixation can be performed without intraoperative body position changes and additional surgical incisions, but its biomechanical defect may trigger complications. Inspired by the cross screw in other fixation devices, we designed an OLIF cage integrated with a low-profile plate and cross screw (LPCS).

METHODS

This study was designed to investigate whether the biomechanical performance of the LPCS OLIF cage is better than that of OLIF with ALSR fixation. The pullout and bending strength of the newly designed conical screw were tested by comparing it with a clinically used cylindrical screw. Different directional fixation strengths of the LPCS OLIF cage were tested by comparing the failure moment and stiffness with the ALSR fixation model. To test the fixation stability and potential risk for screw loosening in models with LPCS OLIF, we also compared the surgical segment's range of motions (ROMs) and stress distributions on OLIF models without and with different AFD fixation under physiological loading conditions.

RESULTS

The bending and pullout strength of the conical screw was better than that of the clinically used screw, and the failure moment and stiffness of the LPCS OLIF model were higher than those of the ALSR model, especially under the extension loading conditions. In which, the maximum failure moment of ALSR fixed OLIF model was 0.88 Nm and 0.76 Nm, while that of the LPCS OLIF model was 9.79 Nm and 7.48 Nm in models with normal and osteoporotic BMD, respectively. Compared to the ALSR fixed OLIF model, failure moment of LPCS models increased by 1012.5% and 884.21% in normal and osteoporotic models, respectively. Moreover, under most physiological loading conditions, the ROM and stress values of the LPCS OLIF model were lower than those of the ALSR model and even slightly lower than those of the OLIF model with bilateral pedicle screw fixation under limited loading conditions.

CONCLUSIONS

Compared to OLIF with ALSR fixation, the newly developed LPCS OLIF cage demonstrates inherent biomechanical advantages in establishing immediate postoperative stability and reducing complications related to stress concentration. However, the conclusions of current research should still be validated through in vitro mechanical tests and clinical trials.

Deterioration of the fixation segment's stress distribution and the strength reduction of screw holding position together cause screw loosening in ALSR fixed OLIF patients with poor BMD

The vertebral body's Hounsfield unit (HU) value can credibly reflect patients' bone mineral density (BMD). Given that poor bone-screw integration initially triggers screw loosening and regional differences in BMD and strength in the vertebral body exist, HU in screw holding planes should better predict screw loosening. According to the stress shielding effect, the stress distribution changes in the fixation segment with BMD reduction should be related to screw loosening, but this has not been identified. We retrospectively collected the radiographic and demographic data of 56 patients treated by single-level oblique lumbar interbody fusion (OLIF) with anterior lateral single rod (ALSR) screw fixation. BMD was identified by measuring HU values in vertebral bodies and screw holding planes. Regression analyses identified independent risk factors for cranial and caudal screw loosening separately. Meanwhile, OLIF with ALSR fixation was numerically simulated; the elastic modulus of bony structures was adjusted to simulate different grades of BMD reduction. Stress distribution changes were judged by computing stress distribution in screws, bone-screw interfaces, and cancellous bones in the fixation segment. The results showed that HU reduction in vertebral bodies and screw holding planes were independent risk factors for screw loosening. The predictive performance of screw holding plane HU is better than the mean HU of vertebral bodies. Cranial screws suffer a higher risk of screw loosening, but HU was not significantly different between cranial and caudal sides. The poor BMD led to stress concentrations on both the screw and bone-screw interfaces. Biomechanical deterioration was more severe in the cranial screws than in the caudal screws. Additionally, lower stress can also be observed in fixation segments' cancellous bone. Therefore, a higher proportion of ALSR load transmission triggers stress concentration on the screw and bone-screw interfaces in patients with poor BMD. This, together with decreased bony strength in the screw holding position, contributes to screw loosening in osteoporotic patients biomechanically. The trajectory optimization of ALSR screws based on preoperative HU measurement and regular anti-osteoporosis therapy may effectively reduce the risk of screw loosening.

A novel scoliosis instrumentation using special superelastic nickel-titanium shape memory rods: a biomechanical analysis using a calibrated computer model and data from a clinical trial

STUDY DESIGN

Biomechanical analysis of scoliosis instrumentation using superelastic Nickel-titanium shape memory (SNT) rods.

OBJECTIVE

To compare SNT with conventional Titanium (Ti) and Cobalt-chrome (Co-Cr) rods. A clinical trial has documented comparable efficacy between two adolescent idiopathic scoliosis (AIS) cohorts instrumented using SNT versus conventional Ti rods. The shape memory and superelasticity of the SNT rod are thought to allow easy rod insertion, progressive curve correction, and correction from spinal tissue relaxation, but study is yet to be done to assess the effects of the shape memory and superelasticity.

METHODS

Instrumentations of AIS patients from the clinical trial were computationally simulated using SNT, Ti and Co-Cr rods (5.5 or 6 mm; 30°, 50° or 60° sagittal contouring angles; 0°, 25° or 50° coronal over-contouring angles). Curve correction, its improvement from stress relaxation in the spine, and loads in the instrumentation constructs were computed and compared.

RESULTS

The simulated main thoracic Cobb angles (MT) and thoracic kyphosis with the SNT rods were 4°-7° higher and 1°-2° lower than the Ti and Co-Cr rods, respectively. Bone-implant forces with Ti and Co-Cr rods were higher than the SNT rods by 84% and 130% at 18 °C and 35% and 65% at 37 °C, respectively (p < 0.001). Further corrections of the MT from the simulated stress relaxation in the spine were 4°-8° with the SNT rods versus 2°-5° with the Ti and Co-Cr rods (p < 0.001).

CONCLUSION

This study concurs with clinical observation that the SNT rods are easier to insert and can result in similar correction to the conventional rods. The SNT rods allow significantly lower bone-implant forces and have the ability to take advantage of post-instrumentation correction as the tissues relax.

Motion response of a polycrystalline diamond adaptive axis of rotation cervical total disc arthroplasty

BACKGROUND

Cervical fusion is associated with adjacent segment degeneration. Cervical disc arthroplasty is considered an alternative to reduce risk of adjacent segment disease. Kinematics after arthroplasty should closely replicate healthy in vivo kinematics to reduce adjacent segment stresses. The purpose of this study was to assess the kinematics of a polycrystalline diamond cervical disc prosthesis.

METHODS

Nine cadaveric C3-T1 spines were tested intact and after one (C5-C6) and two level (C5-C7) arthroplasty (Triadyme-C, Dymicron Inc., Orem, UT, USA). Kinematics were evaluated in flexion-extension, lateral bending, and axial rotation.

FINDINGS

Prosthesis placement at C5-C6 and C6-C7 was 0.5 mm anterior and 0.6 mm posterior to midline respectively. C5-C6 flexion-extension motion was 12.8° intact and 10.5° after arthroplasty. C6-C7 flexion-extension motion was 10.0 and 11.4° after arthroplasty. C5-C6 lateral bending reduced from 8.5 to 3.7° after arthroplasty and at C6-C7 from 7.5 to 5.1°. C5-C6 axial rotation decreased from 10.4 to 6.2° after arthroplasty and at C6-C7 from 7.8 to 5.3°. Segmental lordosis increased by 4.2°, and middle disc height by 1.4 mm after arthroplasty. Change in center of rotation from intact to arthroplasty averaged 0.9 mm posteriorly and 0.1 mm caudally at C5-C6, and 1.4 mm posteriorly and 0.3 mm cranially at C6-C7.

INTERPRETATION

The cervical disc arthroplasty evaluated restored flexion-extension motion to intact levels and moderately increased segmental stiffness. Disc height increased by up to 1.5 mm and segmental lordosis by 4.2°. The unique prosthesis design allowed the axis of rotation after arthroplasty to closely mimic the native location.