Analysis of Short Implants and Lateralization of the Inferior Alveolar Nerve With 2-Stage Dental Implants by Finite Element Method

In-Block Lateralization as a New Technique for Mobilization of the Inferior Alveolar Nerve: A Technique Case Series

The edentulous atrophic posterior mandible is often a great challenge for implant rehabilitation. Although a number of treatment options have been proposed, including the use of short implants and surgical grafting techniques, in cases of severe bone atrophy, techniques for mobilization of the inferior alveolar nerve (IAN) have been shown to be efficient, with good results. Four female patients underwent IAN lateralization for prosthetic rehabilitation of the posterior mandible from 2013 to 2019, with 3 years to 5 years and 3 months of follow-up. This case series describes a new technique for mobilization of the IAN, named in-block lateralization, to facilitate access to the IAN and to reduce nerve manipulation. The implant is immediately installed (allowing nerve lateralization in unitary spaces), and the original mandibular anatomy is restored with autogenous bone from the original bed during the same surgical procedure. When well indicated and well performed, this new approach provides better and easier visualization of the IAN and safer manipulation aiming to achieve good results for implant stability and minimal risk of neurosensory disturbances, allowing rehabilitation even in unitary spaces.

Stress distribution with extra-short implants in an angled frictional system: A finite element analysis study

STATEMENT OF PROBLEM

Short and extra-short implants with Morse taper connections were developed to avoid grafting procedures. How the stresses around these implants differ with abutments of different angulations is unclear.

PURPOSE

The purpose of this finite element study was to analyze the stress distribution in different structures (abutment, implant, and bone) of an extra-short implant with a Morse taper connection to the abutment (Arcsys-FGM-Brazil) (5.0×5.0 mm and 4.3×5.0 mm) when different abutment degrees were used.

MATERIAL AND METHODS

Eight 3D models were designed according to each group under analysis: group 5DS (5.0×5.0-mm implants with straight abutment), group 5DA (5.0×5.0-mm implants with 20-degree angled abutments), group 4DS (4.3×5.0-mm implants with straight abutments), and group 4DA (4.3×5.0-mm implants with 20-degree angled abutments). Axial and oblique loads of 150 N were applied on the mandibular molar crowns.

RESULTS

The oblique loads and angled abutments had higher stress values in the whole model (implant, abutment, and bone) than the axial loads and straight abutments. Implants with a different diameter had almost the same stress distribution on the implant, abutment, and bone. The yield limit was exceeded in the cortical bone with oblique loads and was also exceeded in implant models when an angled abutment with oblique loads was used.

CONCLUSIONS

Extra-short implants with Morse taper connections to the abutment had higher stress concentrations with an angled abutment on oblique loads, and the peri-implant bone was the most damaged structure.

Incidence of Neurosensory Disturbance and Success Rates of Solid-Screw Implants Placed in Conjunction with Inferior Alveolar Nerve Transposition

Background:

Implant-supported prosthetic rehabilitation of a severely atrophic posterior mandibular alveolar ridge is a real challenge. Implant placement in such situations is very difficult and implies the risk of inferior alveolar nerve (IAN) damage.

Purpose:

The purpose of this study is to evaluate the incidence of neurosensory disturbance and the cumulative survival of dental implants placed after the IAN transposition (IANT) procedures followed by dental implants placement.

Materials and Methods:

Twenty International Team for Implantology implants were placed in eight patients following unilateral IANT. In two patients, nerve transposition was performed bilaterally, and hence, a total of 10 IAN transposition surgeries were performed. Neurosensory dysfunction was objectively evaluated by using light touch test (LT), pain test (PT), and 2-point discrimination test (2-DT). In addition, patients were asked to answer a short questionnaire to investigate the individual feeling of discomfort and advantages related to this surgical technique. The mean follow-up periods were 47.1 months (range 12–78 months).

Results:

Neurosensory disturbance (i.e., disturbance registered by the LT, PT, and 2-DT tests) was experienced in 2 of 10 cases. The cumulative implant survival was 100%. However, at the time of data analysis (12–79 months after surgery), all patients indicated that they would go through the surgery again.

Conclusion:

IANT can permit the placement of implants with adequate length and good initial stabilization as used in routine sites, with the same favorable prognosis. All patients felt that they had received benefits from their new prostheses in terms of improved comfort, chewing efficiency, and esthetics.

Complications associated with inferior alveolar nerve reposition technique for simultaneous implant-based rehabilitation of atrophic mandibles. A systematic literature review

INTRODUCTION

Surgical inferior alveolar nerve (IAN) reposition techniques offer an alternative approach to implant-based rehabilitation in patients with severe mandibular atrophy The aim of this systematic review, was to determine the complications associated with the technique and to determine which of two variants (lateralization or transposition) is less invasive.

MATERIALS AND METHODS

An electronic search was conducted in databases complimented by a manual search to identify clinical studies investigating complications derived from these surgical techniques. Only studies of adult humans, published in English during the last seven years were included. The initial search located 78 articles, of which seven were included in analysis on the basis of the following characteristics: four investigated inferior alveolar nerve lateralization (IANL), one inferior alveolar nerve transposition (IANT), and two investigated both reposition techniques.

RESULTS

This review included data from 289 patients who were recruited for lateralization (N=319) or transposition surgery (N=33) making a total of 352 reposition procedures. Five patients (1.73%) suffered persistent damage to the IAN at the end of the follow-up periods. The overall implant survival rate was 99.26% of a total of 817 implants. The most common complications were neurosensory problems, mandibular fracture, infection, implant loss, and insufficient anatomical reconstruction of the atrophic mandible; neurosensory complications (hypoesthesia, paraesthesia, and hyperesthesia caused by traumatic damage to the nerve) were the most prevalent.

CONCLUSIONS

Lateralization of the inferior alveolar nerve would appear to be less invasive as it produces lower percentages of persistent neurosensory disorders (1.56%) than transposition (12.12%). Nevertheless, both techniques offer a viable approach to implant placement in edentulous atrophic mandibles, obtaining predictable clinical and radiological results after 5 years implant loading.

Piezoelectric Surgery in the Inferior Alveolar Nerve Lateralization With Simultaneous Implant Placement: A Case Report

The aim of this case report was to describe the inferior alveolar nerve (IAN) lateralization technique using the piezoelectric device for the posterior rehabilitation of an atrophic mandible with implants. The patient presented the absence of elements 35 and 36 associated with a vertical defect impairing the adequate dental implant placement without IAN damage. A full-thickness mucoperiosteal flap was raised, and a bone window was made with a piezoelectric device centralized on the IAN canal position. After dissection, the IAN was moved buccally with a sterile elastic strip. Morse cone 4.0 × 1.5-mm implants were inserted while the IAN remained retracted. At the 4-month follow-up, the screw-retained prosthesis was installed guaranteeing the recovering masticatory function. In conclusion, the case report showed that the IAN lateralization performed with an adequate surgical technique can be successfully indicated for longer implant placement in edentulous atrophic posterior mandible with no permanent neural damage.

Biomechanical Behavior of Tooth-Implant Supported Prostheses With Different Implant Connections: A Nonlinear Finite Element Analysis

PURPOSE

Biomechanical behavior of tooth-implant-supported prostheses (TISPs) with external and internal implants was compared.

MATERIALS AND METHODS

Two 3-D models of TISP were designed by varying the implant: external (Model EH) and internal hexagons (Model IH). After loading, von Mises stresses were obtained in implants, abutments, and screws. Principal maximum (σmax) and minimum (σmin) stresses were analyzed in periodontal ligament (PL), alveolar bone, and periimplant bone.

RESULTS

Model IH showed lower stress peaks in axial loading in the implant and in the screw but higher in abutment. In oblique loading, Model IH had lower stresses in the implant, but higher in the abutment and in the screw. In the σmax analysis for axial and oblique loads, stress peaks in Model IH were lower in PL, alveolar bone, and periimplant bone. In the σmin analysis for axial load, stress peaks in Model IH were lower in PL, but higher in alveolar bone and in periimplant bone. In oblique load, Model IH showed lower stress peaks in PL and alveolar bone, but higher stress peaks in periimplant bone.

CONCLUSIONS

TISPs with IH implants do present lower risk of biomechanical failure.

Three-Dimensional Finite Element Analysis of Varying Diameter and Connection Type in Implants with High Crown-Implant Ratio

Abstract The aim of this study was to evaluate the effect of varying the diameter, connection type and loading on stress distribution in the cortical bone for implants with a high crown-implant ratio. Six 3D models were simulated with the InVesalius, Rhinoceros 3D 4.0 and SolidWorks 2011 software programs. Models were composed of bone from the posterior mandibular region; they included an implant of 8.5 mm length, diameter Ø 3.75 mm or Ø 5.00 mm and connection types such as external hexagon (EH), internal hexagon (IH) and Morse taper (MT). Models were processed using the Femap 11.2 and NeiNastran 11.0 programs and by using an axial force of 200 N and oblique force of 100 N. Results were recorded in terms of the maximum principal stress. Oblique loading showed high stress in the cortical bone compared to that shown by axial loading. The results showed that implants with a wide diameter showed more favorable stress distribution in the cortical bone region than regular diameter, regardless of the connection type. Morse taper implants showed better stress distribution compared to other connection types, especially in the oblique loading. Thus, oblique loading showed higher stress concentration in cortical bone tissue when compared with axial loading. Wide diameter implant was favorable for improved stress distribution in the cortical bone region, while Morse taper implants showed lower stress concentration than other connections.

Management of Limited Vertical Bone Height in the Posterior Mandible: Short Dental Implants Versus Nerve Lateralization With Standard Length Implants

Inferior alveolar nerve lateralization (IANL) and short dental implants (SDI) are 2 viable implant-based treatment approaches in the presence of atrophied posterior mandible. Despite the risks of dysfunction, infection, and pathologic fractures in IANL, it becomes possible to place standard implants. The purpose of this study was to compare SDI and IANL approaches from clinical and radiographic aspects. Fifteen subjects having unilateral atrophic mandibles were allocated to SDI and IANL treatment groups. Following surgical procedures, early postoperative complications, implant survival, and periimplant clinical and radiographic parameters including probing pocket depth, attachment level, keratinized tissue amount, vertical tissue recession, and marginal bone loss were recorded at baseline and 1-year after prosthetic rehabilitation. In both groups, no implant was lost. Except usual postoperative complications, 2 patients had transient paraesthesia after IANL. According to time-dependent evaluation, both groups showed significant increase in probing pocket depth and attachment level at 1-year follow-up compared with baseline (P < 0.05). Except a slight but significant increase in mesial surface of SDI group (P < 0.05), no remarkable time-dependent change was identified in vertical tissue recession. Keratinized tissue amount did not exhibit any inter- or intragroup difference during whole study period. Marginal bone loss did not show any difference between IANL and SDI groups at follow-up. SDI placement or standard length implant placement with IANL can be considered promising alternatives in the treatment of atrophic mandibular posterior regions. However, SDI may be preferred in terms of lower complication risk.

In Vitro Evaluation of the Primary Stability of Short and Conventional Implants

The objective of this study was to evaluate the primary stability of short and conventional dental implants with different platform types at different site densities in vitro. One hundred twenty implants were placed in polyurethane blocks that simulate different bone densities (bone types I and IV). The implants were divided into 10 groups, with 12 implants each according to the type of prosthetic connections (external hexagon, EH; morse taper, MT) and size of the implants (conventional: 4 × 10 mm; short: 5 × 5, 5.5 × 5, 5 × 6, and 5.5 × 6 mm). Insertion torque and resonance frequency analyses were performed to evaluate the primary stability. The Kruskal-Wallis test complemented by Dunn's test and the Mann-Whitney test were used for statistical analysis. These tests were applied at the confidence level of 95% (P < .05). The implants installed in blocks with density type IV exhibited reduced insertion torque compared with implants placed in blocks with density type I. Short implants with EH exhibited increased insertion torque compared with short implants with MT in blocks with bone density type I. In general, implants installed in blocks with density type I exhibited greater primary stability. The short implants with EH with a 5.5-mm diameter and the short implants with MT with a 5-mm diameter exhibited reduced primary stability. No differences between short and conventional implants were noted. Short implants have primary stability and insertion torque at least equivalent to conventional implants irrespective of the platform type and density of the site.

Dental Implant Length and Diameter: A Proposed Classification Scheme

PURPOSE

To propose a length-and-diameter-based classification scheme for dental implants to standardize terminology in the dental literature and communication between interested parties.

MATERIALS AND METHODS

This study was mainly based on searching two major resources: published scientific research papers and 14 of the most popular dental implant manufacturers. Indexed databases were searched from January 2004 up to and including February 2016 using the keywords "dental implant length" and "dental implant diameter." Retrieved titles and abstracts were screened, and related full-text articles were reviewed. Full-text articles that clearly stated the terms and measurements of implants used were included and considered for proposing this classification scheme.

RESULTS

The initial search for implant diameter and length yielded 1007 and 936 articles, respectively. A total of 85 studies (41 about diameter, 44 about length) were selected and reviewed. The remaining studies (966 about diameter, 892 about length) that did not abide by the eligibility criteria were excluded. The terms "long," "short," "standard," "wide," and "narrow" were the most commonly used terms in the literature. A classification scheme for implants by diameter and length was proposed.

CONCLUSIONS

Indexed publications contain a variety of terms used by authors to describe diameter and length of dental implants without conformity and standardization. The classification scheme proposed in this article could serve as a reference for interested parties.

Comparative Finite Element Analysis of Short Implants and Lateralization of the Inferior Alveolar Nerve With Different Prosthesis Heights

The lateralization of the inferior alveolar nerve (LIAN) and short implants are efficient options for rehabilitation of the posterior atrophic mandible. However, the loss of bone leads to prosthesis with greater height and lever effect that in turn can have different impact on treatments. Through the finite element method, the present study tests the hypothesis that conventional implants placed under LIAN and short implants have similar risk of bone loss regarding variable height of the crown and that crown-to-implant ratio is not a reliable resource to evaluate risk in these treatments. Computed tomography scans of mandibles were processed and implants and prosthetic components were reverse engineered for reconstruction of three-dimensional models to simulate 3 elements fixed partial dentures supported by 2 osseointegrated implants. The models of implants were based on MK III implants (Nobel Biocare, Zurich, Switzerland) with 4 mm in diameter by 7 mm in length representing short implants, and 15 mm in length representing implants used in LIAN. The implant/crown ratio for short implants was 1:1.5, 1:2, and 1:2.5 and LIAN models were modeled with exactly the same prosthesis, resulting in implant/crown ratios of 1:0.67, 1:0.89, and 1:1.12. The results partially rejected the hypothesis that LIAN and short implants have similar risk of bone loss, showing that although LIAN results were better in the models evaluated, the variations in height had proportionally similar impact on both treatments and accepted the hypothesis that crown-to-implant ratio was not a reliable resource to evaluate risk.

Nerve Retraction During Inferior Alveolar Nerve Repositioning Procedure: A New Simple Method and Review of the Literature

Nerve repositioning surgery is one of the treatments chosen for the patients with edentulous posterior atrophic mandible. Like any other treatments, this therapy has its advantages and disadvantages, indications and contraindications. The most important complication of this procedure is neurosensory disturbance. This problem may occur at different stages of the treatment. One common time when nerve damage happens is when the nerve is located outside the canal and drilling and insertion of the implant are performed. Accordingly, this report describes a simple and feasible method to retract and protect nerves outside the canal during the treatment of nerve transposition. This will reduce the risk of nerve damage.

Cortical Bone Augmentation Versus Nerve Lateralization for Treatment of Atrophic Posterior Mandible: A Retrospective Study and Review of Literature

PURPOSE

We sought to assess implant success/survival/failure rate following cortical autogenous tenting technique (CATT) versus inferior alveolar nerve transposition (IANT) in the posterior mandible.

MATERIALS AND METHODS

Patients who underwent these two procedures between 2007 and 2011 were analyzed. CATT was performed using lateral ramus block graft and implants were inserted simultaneously or after 4 to 6 months. In IANT, implants were placed simultaneously after nerve transposition with or without mental foramen involvement. Data regarding marginal bone level (MBL), pus discharge (PD), neurosensory dysfunction (NSD), implant mobility, and failure were collected. Success rate was measured based on Pisa Consensus. Independent sample t-test with a significance level of 0.05 was used to compare implant dimensions and MBL changes between the two techniques.

RESULTS

A total of 118 patients with a mean age of 54.85 years were included. The mean follow-up after CATT and IANT was 37.97 and 18.51 months, respectively. The overall survival and success rates of dental implants in the CATT group were 98.73% and 71.52%, respectively. The corresponding values for IANT subjects were 98.74% and 94.56%, respectively. Implant length and diameter in IANT group were significantly longer and wider than implants used after CATT (p value < .001). MBL changes in both techniques were less than 1 mm (p value = .79). Two cases of NSD, seven PD, and two implant failures were found in the CATT group. For IANT patients, seven permanent NSD, two PD, two implant failures, and one mandibular fracture were documented.

CONCLUSION

Both techniques had implant survival rates similar to implants placed in unaltered bone. A higher implant success rate, albeit with higher incidence of long-lasting nerve damage, was observed in the IANT group.

Evaluation of mandibular angle ostectomy using three-dimensional finite element analysis

PURPOSE

This study was designed to investigate the stress and the displacement distributions of the mandible after mandibular angle ostectomy (MAO) by means of three-dimensional finite element analysis.

METHODS

On the basis of a female patient with a prominent angle of the mandible, the finite element models were generated by helical computed tomography and related software and were analyzed under muscle forces and 3 kinds of biting conditions, including intercuspal position (ICP), incisal clenching (INC), and right unilateral molar clenching (RMOL). The mandibular stress and displacement distributions were analyzed by Abaqus software.

RESULTS

In the model of MAO, the increased stress and the decreased displacement was found in ICP, INC, and RMOL at the area of mandibular angle. The stress and the displacement increased in ICP and RMOL, whereas the others remained unchanged in INC at the area of mandibular condylar neck.

CONCLUSIONS

The results of this study have shown that MAO could alter biomechanical characteristics in the operated mandible, which suggested that a greater hit on face may lead to a higher incidence rate of condyle fracture and a lower incidence rate of angle fracture after MAO.