Organosilane-functionalization of nanostructured indium tin oxide films

A potent anticoagulant hybrid of snake venom derived FIX-binding protein and anti-factor IX RNA aptamer: Assessed by in-silico and electrochemical analyses

Anticoagulant therapies are crucial in the management of surgical complications as well as the prophylaxis of thrombosis. Many studies are being conducted on the Habu snake-venom anticoagulant, FIX-binding protein (FIX-Bp), for its greater potency and strong affinity to FIX clotting factor. On the other hand, the capacity to promptly reverse such acute anticoagulation is equally important. Combining a reversible anticoagulant with FIX-Bp may be advantageous in maintaining the balance between adequate anticoagulation and repealing when necessary. In this study, authors integrated FIX-Bp and RNA aptamer-based anticoagulants into a single target, FIX clotting factor, in order to achieve a robust anticoagulant effect. An in-silico and electrochemical approach were used to investigate the combination of FIX-Bp and RNA aptamers as a bivalent anticoagulant and to verify the competing or predominant binding sites of each anticoagulant. The in-silico analysis discovered that both the venom- and aptamer-anticoagulant had a strong affinity for the FIX protein at the Gla-domain and EGF-1 domain by holding 9 conventional hydrogen bonds with the binding energy of -34.859 kcal/mol. The electrochemical technique verified that both anticoagulants had different binding sites. The impedance load upon RNA aptamer binding to FIX protein was 14 %, whereas the addition of FIX-Bp caused a significant impedance rise of 37 %. This indicates that the addition of aptamers prior to FIX-Bp is a promising strategy for the conception of a hybrid anticoagulant.

Controlled Silanization of Transparent Conductive Oxides as a Precursor of Molecular Recognition Systems

The search for new molecular recognition systems has become the goal of modern electrochemistry. Creating a matrix in which properties can be controlled to obtain a desired analytical signal is an essential part of creating such tools. The aim of this work was to modify the surface of electrodes based on transparent conductive oxides with the use of selected alkoxysilanes (3-aminopropyltrimethoxysilane, trimethoxy(propyl)silane, and trimethoxy(octyl)silane). Electrochemical impedance spectroscopy and cyclic voltammetry techniques, as well as contact angle measurements, were used to determine the properties of the obtained layers. Here, we prove that not only was the structure of alkoxysilanes taken into account but also the conditions of the modification process-reaction conditions (time and temperature), double alkoxysilane modification, and mono- and binary component modification. Our results enabled the identification of the parameters that are important to ensure the effectiveness of the modification process. Moreover, we confirmed that the selection of the correct alkoxysilane allows the surface properties of the electrode material to be controlled and, consequently, the charge transfer process at the electrode/solution interface, hence enabling the creation of selective molecular recognition systems.

Good Choice of Electrode Material as the Key to Creating Electrochemical Sensors-Characteristics of Carbon Materials and Transparent Conductive Oxides (TCO)

The search for new electrode materials has become one of the goals of modern electrochemistry. Obtaining electrodes with optimal properties gives a product with a wide application potential, both in analytics and various industries. The aim of this study was to select, from among the presented electrode materials (carbon and oxide), the one whose parameters will be optimal in the context of using them to create sensors. Electrochemical impedance spectroscopy and cyclic voltammetry techniques were used to determine the electrochemical properties of the materials. On the other hand, properties such as hydrophilicity/hydrophobicity and their topological structure were determined using contact angle measurements and confocal microscopy, respectively. Based on the research carried out on a wide group of electrode materials, it was found that transparent conductive oxides of the FTO (fluorine doped tin oxide) type exhibit optimal electrochemical parameters and offer great modification possibilities. These electrodes are characterized by a wide range of work and high chemical stability. In addition, the presence of a transparent oxide layer allows for the preservation of valuable optoelectronic properties. An important feature is also the high sensitivity of these electrodes compared to other tested materials. The combination of these properties made FTO electrodes selected for further research.

Nanostructure ITO and Get More of It. Better Performance at Lower Cost

In this paper, we investigated how different growth conditions (i.e., temperature, growth time, and composition) allows for trading off cost (i.e., In content) and performance of nanostructured indium tin oxide (ITO) for biosensing applications. Next, we compared the behavior of these functionalized nanostructured surfaces obtained in different growth conditions between each other and with a standard thin film as a reference, observing improvements in effective detection area up to two orders of magnitude. This enhanced the biosensor’s sensitivity, with higher detection level, better accuracy and higher reproducibility. Results show that below 150 °C, the growth of ITO over the substrate forms a homogenous layer without any kind of nanostructuration. In contrast, at temperatures higher than 150 °C, a two-phase temperature-dependent growth was observed. We concluded that (i) nanowire length grows exponentially with temperature (activation energy 356 meV) and leads to optimal conditions in terms of both electroactive surface area and sensitivity at around 300 °C, (ii) longer times of growth than 30 min lead to larger active areas and (iii) the In content in a nanostructured film can be reduced by 10%, obtaining performances equivalent to those found in commercial flat-film ITO electrodes. In summary, this work shows how to produce appropriate materials with optimized cost and performances for different applications in biosensing.

Tuning the deposition parameters for optimizing the faradaic and non-faradaic electrochemical performance of nanowire array-shaped ITO electrodes prepared by electron beam evaporation

Nanostructured indium tin oxide (ITO) surfaces present an interesting yet unusual combination of properties (high electrical conductivity and optical transparency) at a high surface-to-volume ratio. Thus, previous studies presented nanostructured ITO electrodes as potentially suitable platforms for electrochemical biosensors, but still there is a lack of research on the optimization of preparation methods for such electrodes. We present a systematic study on the properties of nanostructured ITO electrodes prepared by physical deposition, where the substrate temperature was tuned for achieving the best combination of structural properties (namely electrical conductivity and optical transparency) and electrochemical performance. Analysis of faradaic cyclic voltammetry (CV) was performed to determine the electroactive surface area of the samples, and these results were benchmarked against those obtained by non-faradaic CV and Mott-Schottky (MS) analysis. The latter was useful to determine the dependence of some intrinsic features of the semiconductor on the substrate temperature during deposition. The results show that, out of a wide temperature range covering from 200 °C to 500 °C, there is a two-phase temperature-dependent growth, explained by the Stranski-Krastanov and self-catalytic vapor-liquid-solid (VLS) methods, and, on the other hand, that there is an optimal growth temperature at 300 °C that maximizes the electroactive surface area and sensitivity. This means that cost-effective electrodes can be prepared at low temperatures outperforming in terms of electroactive surface area, surface capacitance and sensitivity. As a proof-of-concept, nanostructured ITO electrodes were electrochemically derivatized with aryl diazonium salts (as a first step towards biochemical functionalization), and the performance of the optimized electrodes was tested in a real scenario.

Electrochemically driven host–guest interactions on patterned donor/acceptor self-assembled monolayers

Patterned ferrocene/anthraquinone self-assembled monolayers are selectively oxidised or reduced to locally control the formation of host–guest complexes on the surface.