Emittance Preservation in an Aberration-Free Active Plasma Lens

Experimental observation of the electron beam focusing effect induced by plasma currents with opposite directions

We report on the experimental observation of the focusing effect of a 50MeV accelerator electron beam in a gas-discharge plasma target. The plasma is generated by igniting an electric discharge in two collinear quartz tubes, with the currents up to 1.5kA flowing in opposite directions in either of the two tubes. In such plasma current configuration, the electron beam is defocused in the first discharge tube and focused with a stronger force in the second one. With symmetric plasma currents, asymmetric effects are, however, induced on the beam transport process and the beam radius is reduced by a factor of 2.6 compared to the case of plasma discharge off. Experimental results are supported by two-dimensional particle-in-cell simulations.

Formation and properties of spatially inhomogeneous plasma density gratings

Volume plasma density gratings receive increasing interest since, compared to solid-state optical media, they posses significantly higher damage thresholds. The gratings are produced by counterpropagating laser pulses in underdense plasma. When analyzing their optical properties, usually they are assumed to be homogeneous in space. The latter assumption, however, breaks down, especially when the gratings are produced by short high-power laser pump pulses. Then, generically the plasma grating posses an inhomogeneous envelope which results from the superposition of the pump pulses envelopes. The present paper discusses the effect of grating inhomogeneity on reflection and transmission of probe pulses. A Gaussian plasma density grating becomes an apodized grating which offers significant improvement over homogeneous gratings due to side-lobe suppression while maintaining reflectivity and a narrow bandwidth. On the other hand, the reflected probe pulses receive a chirp which depends on the spatial scale. For a Gaussian grating a cubic spectral phase appears. Numerical particle-in-cell simulations are supported by theoretical analysis based on coupled mode equations as well as an effective medium approach.

Compact all-optical precision-tunable narrowband hard Compton X-ray source

Readily available bright X-ray beams with narrow bandwidth and tunable energy promise to unlock novel developments in a wide range of applications. Among emerging alternatives to large-scale and costly present-day radiation sources which severely restrict the availability of such beams, compact laser-plasma-accelerator-driven inverse Compton scattering sources show great potential. However, these sources are currently limited to tens of percent bandwidths, unacceptably large for many applications. Here, we show conceptually that using active plasma lenses to tailor the electron bunch-photon interaction, tunable X-ray and gamma beams with percent-level bandwidths can be produced. The central X-ray energy is tunable by varying the focusing strength of the lens, without changing electron bunch properties, allowing for precision-tuning the X-ray beam energy. This method is a key development towards laser-plasma-accelerator-driven narrowband, precision tunable femtosecond photon sources, enabling a paradigm shift and proliferation of compact X-ray applications.

Reduced model of plasma evolution in hydrogen discharge capillary plasmas

A model describing the evolution of the average plasma temperature inside a discharge capillary device including Ohmic heating, heat loss to the capillary wall, and ionization and recombination effects is developed. Key to this approach is an analytic quasistatic description of the radial temperature variation which, under local thermal equilibrium conditions, allows the radial behavior of both the plasma temperature and the electron density to be specified directly from the average temperature evolution. In this way, the standard set of coupled partial differential equations for magnetohydrodynamic (MHD) simulations is replaced by a single ordinary differential equation, with a corresponding gain in simplicity and computational efficiency. The on-axis plasma temperature and electron density calculations are benchmarked against existing one-dimensional MHD simulations for hydrogen plasmas under a range of discharge conditions and initial gas pressures, and good agreement is demonstrated. The success of this simple model indicates that it can serve as a quick and easy tool for evaluating the plasma conditions in discharge capillary devices, particularly for computationally expensive applications such as simulating long-term plasma evolution, performing detailed input parameter scans, or for optimization using machine-learning techniques.

Combining laser interferometry and plasma spectroscopy for spatially resolved high-sensitivity plasma density measurements in discharge capillaries

Precise characterization and tailoring of the spatial and temporal evolution of plasma density within plasma sources are critical for realizing high-quality accelerated beams in plasma wakefield accelerators. The simultaneous use of two independent diagnostics allowed the temporally and spatially resolved detection of plasma density with unprecedented sensitivity and enabled the characterization of the plasma temperature in discharge capillaries for times later than 0.5 µs after the initiation of the discharge, at which point the plasma is at local thermodynamic equilibrium. A common-path two-color laser interferometer for obtaining the average plasma density with a sensitivity of 2 × 10¹⁵ cm^-2 was developed together with a plasma emission spectrometer for analyzing spectral line broadening profiles with a resolution of 5 × 10¹⁵ cm^-3. Both diagnostics show good agreement when applying the spectral line broadening analysis methodology of Gigosos and Cardeñoso in the temperature range of 0.5 eV-5.0 eV. For plasma with densities of 0.5-2.5 × 10¹⁷ cm^-3, temperatures of 1 eV-7 eV were indirectly measured by combining the diagnostic information. Measured longitudinally resolved plasma density profiles exhibit a clear temporal evolution from an initial flat-top to a Gaussian-like shape in the first microseconds as material is ejected out from the capillary. These measurements pave the way for highly detailed parameter tuning in plasma sources for particle accelerators and beam optics.

Modeling and diagnostics for plasma discharge capillaries

In this paper, we show how plasma discharge capillaries can be numerically modeled as resistors within an RLC-series discharge circuit, allowing for a simple description of these systems, while taking into account heat and radiation losses. An analytic radial model is also provided and compared to the numerical model for plasma discharge capillaries at thermal equilibrium, with corrections due to radiation losses. Finally, diagnostic techniques based on visible spectroscopy of plasma emission lines are discussed both for atomic and molecular gases, comparing experimental results with numerical simulations and theoretical calculations.

Plasma volume holograms for focusing and mode conversion of ultraintense laser pulses

Beating of a broad laser reference beam with a quite general focused object beam inside a plasma volume generates a dynamic plasma hologram. Both beams may be of moderate intensity. The volume hologram can be read out by an ultraintense main beam (of similar structure as the reference beam) producing an object beam replica. For the latter, intensity in the focus may become extremely large. As an application, the possibility of a read-out focused Gaussian laser pulse with intensity of several 10^{19}W/cm^{2} in focus is shown by three-dimensional numerical simulations. Besides the focusing possibility, the hologram may also act as a mode converter for high-intensity laser pulses. Generating a plasma hologram with a focused Laguerre-Gaussian object beam results in a staggered plasma density grating, allowing the production of high-intensity vortex beam replica.

FLASHForward: plasma wakefield accelerator science for high-average-power applications

The FLASHForward experimental facility is a high-performance test-bed for precision plasma wakefield research, aiming to accelerate high-quality electron beams to GeV-levels in a few centimetres of ionized gas. The plasma is created by ionizing gas in a gas cell either by a high-voltage discharge or a high-intensity laser pulse. The electrons to be accelerated will either be injected internally from the plasma background or externally from the FLASH superconducting RF front end. In both cases, the wakefield will be driven by electron beams provided by the FLASH gun and linac modules operating with a 10 Hz macro-pulse structure, generating 1.25 GeV, 1 nC electron bunches at up to 3 MHz micro-pulse repetition rates. At full capacity, this FLASH bunch-train structure corresponds to 30 kW of average power, orders of magnitude higher than drivers available to other state-of-the-art LWFA and PWFA experiments. This high-power functionality means FLASHForward is the only plasma wakefield facility in the world with the immediate capability to develop, explore and benchmark high-average-power plasma wakefield research essential for next-generation facilities. The operational parameters and technical highlights of the experiment are discussed, as well as the scientific goals and high-average-power outlook. This article is part of the Theo Murphy meeting issue 'Directions in particle beam-driven plasma wakefield acceleration'.

Plasma wakefield linear colliders-opportunities and challenges

A linear electron-positron collider operating at TeV-scale energies will provide high precision measurements and allow, for example, precision studies of the Higgs boson as well as searches for physics beyond the standard model. A future linear collider should produce collisions at high energy, with high luminosity and with a good wall plug to beam power transfer efficiency. The luminosity per power consumed is a key metric that can be used to compare linear collider concepts. The plasma wakefield accelerator has demonstrated high-gradient, high-efficiency acceleration of an electron beam and is therefore a promising technology for a future linear collider. We will go through the opportunities of using plasma wakefield acceleration technology for a collider, as well as a few of the collider-specific challenges that must be addressed in order for a high-energy, high luminosity-per-power plasma wakefield collider to become a reality. This article is part of the Theo Murphy meeting issue 'Directions in particle beam-driven plasma wakefield acceleration'.

Compact Multistage Plasma-Based Accelerator Design for Correlated Energy Spread Compensation

The extreme electromagnetic fields sustained by plasma-based accelerators could drastically reduce the size and cost of future accelerator facilities. However, they are also an inherent source of correlated energy spread in the produced beams, which severely limits the usability of these devices. We propose here to split the acceleration process into two plasma stages joined by a magnetic chicane in which the energy correlation induced in the first stage is inverted such that it can be naturally compensated in the second. Simulations of a particular 1.5-m-long setup show that 5.5 GeV beams with relative energy spreads of 1.2×10^{-3} (total) and 2.8×10^{-4} (slice) could be achieved while preserving a submicron emittance. This is at least one order of magnitude below the current state of the art and would enable applications such as compact free-electron lasers.