Automated transepithelial electrical resistance measurements of the EpiDerm reconstructed human epidermis model

Reconstructed Human Epidermis: An Alternative Approach for In Vitro Bioequivalence Testing of Topical Products

The use of in vitro human skin permeation tests is of value when addressing the quality and equivalence of topical drug products in Europe and the US. Human skin is the membrane of choice for these studies. The use of human skin as a membrane is hindered by limited access, high variability of results, and limited applicability for drugs with low skin permeability. Reconstructed human epidermis (RhE) models are validated as skin surrogates for safety tests and have been explored for percutaneous absorption testing. Clotrimazole poorly permeates human skin and is widely available for topical treatments. In this study, clotrimazole creams were used to test the ability of RhE to be used as biological membrane for bioequivalence testing, based on the Draft Guideline on Quality and Equivalence of Topical Products (CHMP/QWP/708282/2018) using a discriminative and modified in vitro permeation test (IVPT). To fulfill the validation of a discriminatory method, Canesten^® 10 mg/g cream was compared with a test product with the same drug strength, along with two “negative controls” dosed at a 50% and 200% drug strength. Products were compared in finite dose conditions, regarding maximal flux (J_max) and the total amount of drug permeated (A_total). The results showed the discriminatory power of the method among the three drug strengths with no interference of the placebo formulation. The study design and validation complied with the requirements established in the guideline for a valid IVPT. This new test system allowed for the equivalence comparison between test and comparator product. Higher permeability of the RhE compared to human skin could be observed. This arose as a strength of the model for this modified IVPT bioequivalence testing, since comparing permeation profiles among products is envisaged instead of drawing absolute conclusions on skin permeation extent. These results may support the acceptance of RhE as biological membranes for modified IVPT in bioequivalence testing of topical products.

Enabling 3D hepatocyte spheroids for microphysiometry

Advances in the areas of tissue engineering and microfabrication techniques have enabled promising in vitro platforms, known as Organs-on-Chips, with the aim of mimicking complex in vivo conditions for more accurate toxicology studies. To analyze the physiological change induced by chemicals or toxic substances continuously, sensors can be used in order to measure the intracellular and extracellular environment of single cells, cell constructs, or tissue, and therefore the integration of monitoring techniques into 3D tissue culture platforms provides an essential step for the next generation Organ-on-Chip platforms. However, current in vitro platforms are not capable of combining the culture of 3D models with monitoring techniques. To address this, a novel spheroid encapsulation is designed for fluidic contact between 3D models in microwells and Intelligent Mobile Lab for In Vitro Diagnostics (IMOLA-IVD) BioChip sensors while preventing spheroid fusion. In this work, spheroid culturing protocols were developed for optimized spheroid growth and an evaluation of spheroid integrity on different porous layers was performed in order to provide a defined spheroid encapsulation on BioChip sensors.

A novel lab-on-a-chip platform for spheroid metabolism monitoring

Sensor-based cellular microphysiometry is a technique that allows non-invasive, label-free, real-time monitoring of living cells that can greatly improve the predictability of toxicology testing by removing the influence of biochemical labels. In this work, the Intelligent Mobile Lab for In Vitro Diagnostics (IMOLA-IVD) was utilized to perform cellular microphysiometry on 3D multicellular spheroids. Using a commercial 3D printer, 3 × 3 microwell arrays were fabricated to maintain nine previously cultured HepG2 spheroids on a single BioChip. Integrated layers above and under the spheroids allowed fluidic contact between spheroids in microwells and BioChip sensors while preventing wash out from medium perfusion. Spheroid culturing protocols were optimized to grow spheroids to a diameter of around 620 μm prior to transfer onto BioChips. An ON/OFF pump cycling protocol was developed to optimize spheroid culture within the designed microwells, intermittently perfuse spheroids with fresh culture medium, and measure the extracellular acidification rate (EAR) and oxygen uptake rate (OUR) with the BioChips of the IMOLA-IVD platform. In a proof-of-concept experiment, spheroids were perfused for 36 h with cell culture medium before being exposed to medium with 1% sodium dodecyl sulphate (SDS) to lyse cells as a positive control. These microphysiometry studies revealed a repeatable pattern of extracellular acidification throughout the experiment, indicating the ability to monitor real-time metabolic activity of spheroids embedded in the newly designed tissue encapsulation. After perfusion for 36 h with medium, SDS exposure resulted in an instant decrease in EAR and OUR signals from 37 mV/h (± 5) to 8 mV/h (± 8) and from 308 mV/h (± 21) to -2 mV/h (± 13), respectively. The presented spheroid monitoring system holds great potential as a method to automate screening and analysis of pharmaceutical agents using 3D multicellular spheroid models.