Role of Electrical Conductivity in the Shielding Effectiveness of Composite Polyvinyl Alcohol/Multiwall Carbon Nanotube Nanofibers for Electromagnetic Interference Applications

The shielding effectiveness (SE) against the electromagnetic interference (EMI) of polyvinyl alcohol/multiwall carbon nanotubes (PVA/MWCNTs) composite nanofibers is characteristic of higher absorptivity of the radiation that enhances with the increasing concentration of MWCNTs content in these composites. However, by enriching the content of conductive fillers (MWCNTs), the conductivity of the composites is also stirred up. Concomitantly, the conductivity of these composites contributes toward the reflectivity of the EM radiation from them. Certain applications of the EMI shielding material require a lower level of reflectivity of the EM radiation. This study intends to see how SE of the PVA/MWCNTs composite nanofibers is affected vis-a-vis their conductivity for S-band radiation. Samples of nanofibers, with (5, 10, 15, and 20) wt % of MWCNTs loading in 10 wt % of PVA solution, were prepared through electrospinning and studied for their electrical conductivity and EMI SE. It is observed that by increasing the content of MWCNTs in PVA solution from 5 to 20 wt % the conductivity of the composites tends to increase from 21 to 866 times that of PVA, while the SE increases from 10 db to 25 db over the S-band range of frequencies.

Design and Study of a Wide-Band Printed Circuit Board Near-Field Probe

Magnetic near-field probes (NFP) represent a suitable tool to measure the magnetic field level from a small electromagnetic interference (EMI) source. This kind of antenna is useful as a magnetic field probe for pre-compliance EMC measurements or debugging tasks since the user can scan a printed circuit board (PCB) looking for locations with strong magnetic fields. When a strong H-field point is found, the designer should check the PCB layout and components placement in that area to detect if this could result in an EMI source. This contribution focuses on analyzing the performance of an easy to build and low-cost H-field NFP designed and manufactured using a standard PCB stack-up. Thereby, the frequency range and sensitivity of the NFP-PCB are analyzed through a Finite Element Method (FEM) simulation model that makes it possible to evaluate its sensibility and effective frequency range. The numerical results obtained with the FEM models are validated against measurements to verify the design and performance of our NFP. The FEM model reproduces the experimental procedure, which is used to evaluate the performance of the NFP in terms of sensitivity by means of the simulated near-field distribution. The NFP-PCB has almost a flat response from 180 MHz to 6 GHz, with an almost perfect concordance between numerical and experimental S21 results. The numerical results show an average transmission loss of −27.9 dB by considering the flat response bandwidth, whereas the experimental one is −29.7 dB. Finally, the designed NFP is compared to two high-quality commercial probes in order to analyze its performance.

Highly Bendable and Durable Transparent Electromagnetic Interference Shielding Film Prepared by Wet Sintering of Silver Nanowires

Electromagnetic (EM) wave emissions from wearable or flexible smart display devices can cause product malfunction and have a detrimental effect on human health. Therefore, EM shielding strategies are becoming increasingly necessary. Consequently, herein, we prepared a transparent acrylic polymer-coated/reduced graphene oxide/silver nanowire (Ag NW) (A/RGO/SANW) EM interference (EMI) shielding film via liquid-to-vapor pressure-assisted wet sintering. The film exhibited enhanced Ag NW network formation and antireflection (AR) effects. The wet-sintered Ag NW shielding film had a threshold radius of curvature (ROC) of 0.31 mm at a film thickness of 100 μm, demonstrating its high flexibility, whereas the conventional indium tin oxide (ITO) shielding film had a threshold ROC of ∼5 mm. The EMI shielding effectiveness (SE) of the A/RGO/SANW multilayer film was approximately twice that of the ITO film at a similar relative transmittance (84-85%). The optical relative reflectance of the Ag NW layer was reduced due to the AR effect, and the visible-light transmittance was considerably improved owing to the different refractive indices in the multilayer shielding film. Because the acrylic coating layer had a high contact angle, the multilayer film exhibited high temperature and humidity durability with little change in the SE over 500 h at 85 °C and 85% relative humidity. The multilayer film comprising wet-sintered Ag NW exhibited high flexibility and humidity durability, high shielding performance (more than 24 dB at a relative transmittance of 85% or more), and high mass productivity, making it highly applicable for use as a transparent shielding material for future flexible devices.

Poly(vinylidene fluoride)-based flexible and lightweight materials for attenuating microwave radiations

Two unique materials were developed, like graphene oxide (GO) sheets covalently grafted on to barium titanate (BT) nanoparticles and cobalt nanowires (Co-NWs), to attenuate the electromagnetic (EM) radiations in poly(vinylidene fluoride) (PVDF)-based composites. The rationale behind using either a ferroelectric or a ferromagnetic material in combination with intrinsically conducting nanoparticles (multiwall carbon nanotubes, CNTs), is to induce both electrical and magnetic dipoles in the system. Two key properties, namely, enhanced dielectric constant and magnetic permeability, were determined. PVDF/BT-GO composites exhibited higher dielectric constant compared to PVDF/BT and PVDF/GO composites. Co-NWs, which were synthesized by electrodeposition, exhibited saturation magnetization (Ms) of 40 emu/g and coercivity (Hc) of 300 G. Three phase hybrid composites were prepared by mixing CNTs with either BT-GO or Co-NWs in PVDF by solution blending. These nanoparticles showed high electrical conductivity and significant attenuation of EM radiations both in the X-band and in the Ku-band frequency. In addition, BT-GO/CNT and Co-NWs/CNT particles also enhanced the thermal conductivity of PVDF by ca. 8.7- and 9.3-fold in striking contrast to neat PVDF. This study open new avenues to design flexible and lightweight electromagnetic interference shielding materials by careful selection of functional nanoparticles.