A Digitally Dynamic Power Supply Technique for 16-Channel 12 V-Tolerant Stimulator Realized in a 0.18- μm 1.8-V/3.3-V Low-Voltage CMOS Process

An Energy-Efficient Wireless Power Receiver With One-Step Adiabatic-Bipolar-Supply Generating for Implantable Electrical Stimulation Applications

This paper presents an energy-efficient wireless power receiver for implantable electrical stimulation applications, which can achieve one-step adiabatic bipolar-supply that is generated by a hybrid single-stage dual-output regulating (SSDOR) rectifiers. The structure using only four switches overcomes the disadvantages that the two output voltage values in the traditional dual-output rectifiers are close to each other. A constant-current (CC) controlled adiabatic dynamic voltage scaling (DVS) technique is proposed to minimize the voltage headroom of the stimulating drivers and improve the stimulation efficiency significantly. In addition, the receiver adopts only one general constant on-time (COT) low-frequency control to adjust the stimulation current, reducing both the power consumption and the complexity of the control circuits. The proposed receiver has been fabricated in a 0.18 μm BCD process with ±6 V voltage compliance and 2.5 mA maximum stimulating current. With a current range from ±1.5 mA to ±2.5 mA, the measured maximum average headroom voltage is only 80 mV and the peak total efficiency of the receiver is 85.6 %. The functionalities of the proposed receiver have been successfully verified through in vitro experiments.

Energy-Efficient Power Management Interface With Adaptive HV Multimode Stimulation for Power-Sensor Integrated Patch-Type Systems

An energy-efficient power management interface (PMI) with adaptive high-voltage (HV) stimulation capability is presented for patch-type healthcare devices where power management and sensor readout circuits are integrated. For efficient power supply, it proposes a multimode buck converter with an adaptive mode controller, delivering 95.6% peak power conversion efficiency and over 90% efficiency across a wide 4-440 mA output current range. For energy-efficient stimulation, a HV stimulation system is designed to perform mode-adaptive on/off control, where the charge pump (CP) is adopted for periodic power saving. The CP output is adaptively tuned to minimize the stimulator's power waste by utilizing a bio-impedance path in the sensor circuit. The stimulation core supports multimode functionality of current-/voltage-controlled stimulations with monopolar and bipolar modes, providing ten kinds of various stimulation waveform shape. For efficient system operation, battery interface circuits are included to monitor state-of-charge (SOC) conditions, and a device power adjustment scheme is proposed to provide SOC-based maximum 28% power reduced optimal operation of high-resolution and low-power. The power-sensor integrated circuits were fabricated in a 0.18-μm CMOS process, and the proposed schemes were experimentally verified. For system-level feasibility, a patch-type device prototype was manufactured, and both power and bio-signal interfaces were functionally demonstrated.

Energy efficiency of pulse shaping in electrical stimulation: the interdependence of biophysical effects and circuit design losses

Power efficiency in electrical stimulator circuits is crucial for developing large-scale multichannel applications like bidirectional brain-computer interfaces and neuroprosthetic devices. Many state-of-the-art papers have suggested that some non-rectangular pulse shapes are more energy-efficient for exciting neural excitation than the conventional rectangular shape. However, additional losses in the stimulator circuit, which arise from employing such pulses, were not considered. In this work, we analyze the total energy efficiency of a stimulation system featuring non-rectangular stimuli, taking into account the losses in the stimulator circuit. To this end, activation current thresholds for different pulse shapes and durations in cortical neurons are modeled, and the energy required to generate the pulses from a constant voltage supply is calculated. The proposed calculation reveals an energy increase of 14-51% for non-rectangular pulses compared to the conventional rectangular stimuli, instead of the decrease claimed in previous literature. This result indicates that a rectangular stimulation pulse is more power-efficient than the tested alternative shapes in large-scale multichannel electrical stimulation systems.

Design of Dual-Mode Stimulus Chip With Built-In High Voltage Generator for Biomedical Applications

In this work, a dual-mode stimulus chip with a built-in high voltage generator was proposed to offer a broad-range current or voltage stimulus patterns for biomedical applications. With an on-chip and built-in high voltage generator, this stimulus chip could generate the required high voltage supply without additional supply voltage. With a nearly 20 V operating voltage, the overstress and reliability issues of the stimulus circuits were thoroughly considered and carefully addressed in this work. This stimulus system only requires an area of 0.22 mm² per single channel and is fully on-chip implemented without any additional external components. The dual-mode stimulus chip was fabricated in a 0.25-μm 2.5V/5V/12V CMOS (complementary metal-oxide-semiconductor) process, which can generate the biphasic current or voltage stimulus pulses. The current level of stimulus is up to 5 mA, and the voltage level of stimulus can be up to 10 V. Moreover, this chip has been successfully applied to stimulate a guinea pig in an animal experiment. The proposed dual-mode stimulus system has been verified in electrical tests and also demonstrated its stimulation function in animal experiments.

An Energy-Efficient Implantable-Neural-Stimulator System with Wireless Charging and Dynamic Voltage Output

Neural stimulators have become more and more widely used as an effective tool in neural therapies. To address power supply and consumption issues in this application, an energy-efficient Implantable-Neural-Stimulator system composed of a pulse generator and a wireless charger is proposed and implemented in 0.8μm 40V Bipolar-CMOS-DMOS (BCD) process. By adopting a Single Ended Primary Inductor Converter (SEPIC) and optimizing the switching frequency and the gate width of its power MOSFET, the stimulating output voltage range can cover 0~12V with a maximum output ripple of 0.31%. The proposed charger can charge the implantable battery wirelessly by an inductively coupled resonance circuit. In addition, it can adjust the charging voltage to keep it constantly only a little higher than the battery voltage, which reduces the charging headroom voltage and greatly improves the charging efficiency. The measured maximum power efficiencies of these two modules reach as high as 78.04% and 70.67%, respectively.

Design and In Vivo Verification of a CMOS Bone-Guided Cochlear Implant Microsystem

OBJECTIVE

To develop and verify a CMOS bone-guided cochlear implant (BGCI) microsystem with electrodes placed on the bone surface of the cochlea and the outside of round window for treating high-frequency hearing loss.

METHODS

The BGCI microsystem consists of an external unit and an implanted unit. The external system-on-chip is designed to process acoustic signals through an acquisition circuit and an acoustic DSP processor to generate stimulation patterns and commands that are transmitted to the implanted unit through a 13.56 MHz wireless power and bidirectional data telemetry. In the wireless power telemetry, a voltage doubler/tripler (2X/3X) active rectifier is used to enhance the power conversion efficiency and generate 2 and 3 V output voltages. In the wireless data telemetry, phase-locked loop based binary phase-shift keying and load-shift keying modulators/demodulators are adopted for the downlink and uplink data through high-Q coils, respectively. The implanted chip with four-channel high-voltage-tolerant stimulator generates biphasic stimulation currents up to 800 μA.

RESULTS

Electrical tests on the fabricated BGCI microsystem have been performed to verify the chip functions. The in vivo animal tests in guinea pigs have shown the evoked third wave of electrically evoked auditory brainstem response waveforms. It is verified that auditory nerves can be successfully stimulated and acoustic hearing can be partially preserved.

CONCLUSION AND SIGNIFICANCE

Different from traditional cochlear implants, the proposed BGCI microsystem is less invasive, preserves partially acoustic hearing, and provides an effective alternative for treating high-frequency hearing loss.