Towards Ultrasound Everywhere: A Portable 3D Digital Back-End Capable of Zone and Compound Imaging

A 40-nm 169mW Ultrasound Imaging Processor Supporting Advanced Modes for Hand-Held Devices

Hand-held ultrasound devices have been widely used in the field of healthcare and power-efficient, real-time imaging is essential. This work presents the world's first ultrasound imaging processor supporting advanced modes, including vector flow imaging and elastography imaging. Plane-wave beamforming is utilized to ensure that the pulse repetition frequency (PRF) is sufficiently high for the advanced mode. The storage size and power consumption are minimized through algorithm-architecture co-optimization. The proposed plane-wave beamforming reduces the storage size of the required delay values by 43.7%. By exchanging the processing order, the storage size is reduced by 78.1% for elastography imaging. Parallel beamforming and interleaved firing are employed to achieve real-time imaging for all the supported modes. Fabricated in 40-nm CMOS technology, the proposed processor integrates 4.7M logic gates in core area of 3.24mm. This work achieves a 20.3 higher beamforming rate with 5.3-to-29.1 lower power consumption than the state-of-the-art design. It also has 60% lower hardware complexity (in terms of gate count), in addition to the capability for supporting the advanced mode.

High-Level Synthesis Design of Scalable Ultrafast Ultrasound Beamformer With Single FPGA

Ultrafast ultrasound imaging is essential for advanced ultrasound imaging techniques such as ultrasound localization microscopy (ULM) and functional ultrasound (fUS). Current ultrafast ultrasound imaging is challenged by the ultrahigh data bandwidth associated with the radio frequency (RF) signal, and by the latency of the computationally expensive beamforming process. As such, continuous ultrafast data acquisition and beamforming remain elusive with existing software beamformers based on CPUs or GPUs. To address these challenges, the proposed work introduces a novel method of implementing an ultrafast ultrasound beamformer specifically for ultrafast plane wave imaging (PWI) on a field programmable gate array (FPGA) by using high-level synthesis. A parallelized implementation of the beamformer on a single FPGA was proposed by 1) utilizing a delay compression technique to reduce the delay profile size, which enables both run-time pre-calculated delay profile loading from external memory and delay reuse, 2) vectorizing channel data fetching which is enabled by delay reuse, and 3) using fixed summing networks to reduce consumption of logic resources. Our proposed method presents two unique advantages over current FPGA beamformers: 1) high scalability that allows fast adaptation to different FPGA resources and beamforming speed demands by using Xilinx High-Level Synthesis as the development tool, and 2) allow a compact form factor design by using a single FPGA to complete the beamforming instead of multiple FPGAs. Current Xilinx FPGAs provide the capabilities of connecting up to 1024 ultrasound channels with a single FPGA and the newest JESD204B interface analog front end (AFE). This channel count is much more than the channel count needed by current linear arrays, which normally have 128 or 256 channels. With the proposed method, a sustainable average beamforming rate of 4.83 G samples/second in terms of input raw RF sample was achieved. The resulting image quality of the proposed beamformer was compared with the software beamformer on the Verasonics Vantage system for both phantom imaging and in vivo imaging of a mouse brain. Multiple imaging schemes including B-mode, power Doppler and ULM were assessed to verify that the image quality was not compromised for speed.

An FPGA-Accelerated Parallel Digital Beamforming Core for Medical Ultrasound Sector Imaging

Plane-wave transmission followed by parallel receive beamforming is popular among high frame rate (HFR) ultrasound (US) imaging methods. However, due to technological limitations, HFR imaging is not widely successful in clinical US. The proposed work aims to design a field-programmable gate array (FPGA)-accelerated parallel beamforming core for medical US sector imaging systems. This architecture supports up to 128 channels and forms 28 beams per plane wave transmission in parallel. A block random access memories (BRAMs)-based, 28-read one-write (28R1W) multi-ported delay line architecture is actualized to realize the delay line. In addition, to optimize the FPGA memory, the required beam focusing delays are stored in an external static random access memory (SRAM) and are loaded into the internal delay line registers by a cycle stealing direct memory access (DMA). The FPGA prototype validation and verification are performed on the custom-designed Xilinx-Kintex-7 XC7C410T FPGA-based US imaging platform. The results showed that for a field of view (FOV) of 90° with 0.5° resolution, 640×480 imaging size, a ft/s of 714 is achieved. The performance of the proposed parallel beamformer architecture is compared with existing development works and concluded that the architecture is superior due to its occupancy of FPGA hardware resources and the processing speed.

Automatic Measurement of the Carotid Blood Flow for Wearable Sensors: A Pilot Study

The assessment of the velocity of blood flowing in the carotid, in modern clinical practice, represents an important exam performed both in emergency situations and as part of scheduled screenings. It is typically performed by an expert sonographer who operates a complex and costly clinical echograph. Unfortunately, in developing countries, in rural areas, and even in crowded modern cities, the access to this exam can be limited by the lack of suitable personnel and ultrasound equipment. The recent availability of low-cost, handheld devices has contributed to solving part of the problem, but a wide access to the exam is still hampered by the lack of expert sonographers. In this work, an automated procedure is presented with the hope that, in the near future, it can be integrated into a low-cost, handheld instrument that is also suitable for self-measurement, for example, as can be done today with the finger oximeter. The operator should only place the probe on the neck, transversally with respect to the common tract of the carotid. The system, in real-time, automatically locates the vessel lumen, places the sample volume, and performs an angle-corrected velocity measurement of the common carotid artery peak velocity. In this study, the method was implemented for testing on the ULA-OP 256 scanner. Experiments on flow phantoms and volunteers show a performance in sample volume placement similar to that achieved by expert operators, and an accuracy and repeatability of 3.2% and 4.5%, respectively.

Architecture for an Ultrasound Advanced Open Platform With an Arbitrary Number of Independent Channels

Ultrasound open platforms are programmable and flexible tools for the development and test of novel methods. In most cases, they embed the electronics for the independent control of (maximum) 256 probe elements. However, a higher number of channels is needed for the control of 2-D array probes. This paper presents a system architecture that, through the hardware and software synchronization of multiple ULA-OP 256 scanners, may implement advanced open platforms with an arbitrary number of channels. The proposed solution needs a single personal computer, maintains real-time features, and preserves portability. A prototype demonstrator, composed of two ULA-OP 256 scanners connected to 512 elements of a matrix array, was implemented and tested according to different channel configurations. Experiments performed under MATLAB control confirmed that by doubling the number of elements (from 256 to 512) the signal-to-noise and contrast ratios improve by 9 dB and 3 dB, respectively. Furthermore, as a full 512-channel scanner, the demonstrator can produce real-time B-mode images at 18 Hz, high enough for probe positioning during acquisitions. Also, the demonstrator permitted the implementation of a new high frame rate, bi-plane, triplex modality. All probe elements are excited to simultaneously produce two planar, perpendicular diverging waves. Each scanner independently processes the echoes received by the 256 connected elements to beamform 1300 frames per second. For each insonified plane, good quality morphological (B-mode), qualitative (color flow-), and quantitative (spectral-) Doppler images are finally shown in real-time by a dedicated interface.

Measurement of Quasi-Static 3-D Knee Joint Movement Based on the Registration From CT to US

The measurement of quasi-static 3-D knee joint movement is an important basis for studying the mechanism of knee joint injury. Most of the existing measurement methods make use of computed tomography (CT) and nuclear magnetic resonance (MR) imaging technology and hence have the disadvantages of invasiveness, ionizing radiation, low accuracy, and high cost. To overcome those drawbacks, this article innovatively proposes a 3-D motion measurement system for the knee joint based on the registration of CT images to ultrasound (US) images. More specifically, the lower limbs of a subject were first scanned once to acquire the CT images. A portable handheld device was designed to control a US probe for mechanically scanning the subject's lower limbs in a linear trajectory. During the movement of the subject's lower limbs, the US scanning was performed quasi-statically. The acquired US images were then registered to the CT images, and the 3-D motions of the lower limb bones could be recreated with the bones scanned in CT images. To guarantee the registration accuracy and efficiency, we used the H-shaped multiview slice assembly as the structural image content for the registration process. The experimental results show that our approach can accurately measure the 3-D motion of the knee joint and meet the needs of 3-D motion analysis of knee joint in practice.