A Noise-Reduced Light-to-Frequency Converter for Sub-0.1% Perfusion Index Blood SpO[Formula: see text] Sensing

State-of-the-Art Light to Digital Converter Circuits Applicable in Non-Invasive Health Monitoring Devices to Combat COVID-19 and Other Respiratory Illnesses: A Review

In the past few years, a tremendous advancement in the outcome of biomedical circuits and systems has been reported. Unfortunately, at the time of the sudden outbreak of COVID-19, the electronic engineering researchers felt dearth on their side to combat the pandemic, as no such immediate cutting-edge solutions were ready to recognize the virus with some standard and smart electronic devices. Likely, in this paper, a detailed comparative and comprehensive study on circuit architectures of the biomedical devices is presented. Mostly, this study relates the industry standard circuit schemes applicable in non-invasive health monitoring to combat respiratory illnesses. The trending circuit architectural schemes casted-off to tapeout non-invasive health-care devices available in the past literature are meticulously and broadly discussed in this study. Further, the comprehensive comparison of the state of art of the device performance in terms of supply voltage, chip area, sensitivity, dynamic range, etc. is also shown in this paper. The inclusive design processes of the health monitoring devices from Lab to Industry is thoroughly discussed for the readers. The authors think, that this critical review summarising all the trending and most cited health-care devices in a single paper will alternately help the industrialists to adapt and modify the circuit architectures of the health monitoring devices more precisely and straightforwardly. Finally, the demand for health monitoring devices particularly responsible to detect respiratory illnesses, measuring blood pressure and heart-rate is growing widely in the market after the the incident of COVID-19 and other respiratory diseases.

A Low-Noise Analog Front End with Interstage Systematically Ambient Interference Cancellation for Pulse Oximeter

This paper presents a low-noise analog front end (AFE) with interstage systematically ambient interference cancellation for a pulse oximeter, which is suitable for clinical oxygen saturation (SPO2) detection with a low perfusion index. The fully differential implementation is adopted to have a better rejection performance of common mode interference and noise. Firstly, the proposed interstage systematically ambient interference cancellation is placed in the two gain stages to decrease low frequency noise in the bandwidth of interest (0.1–20 Hz), so that the larger signal-to-noise ratio (SNR) can be achieved to increase the detection accuracy of this system. Secondly, due to the additional gain stage compared with traditional implementation, the current-reuse OTA is employed to have better noise and power efficiency. Thirdly, the auto zero technique is utilized in the LED Driver to decrease the offset voltage and acquire a larger dynamic range (DR) in the low frequency bandwidth of interest. This PPG AFE chip is designed and fabricated in a 180 nm standard CMOS process. The receiver (RX) of this AFE consumes 220 μW from a 1.8 V supply, and the power consumption of the transmitter (TX) is 60 μW from a 3 V supply. The measurement results show that the input-referred noise current of 2.3 pA/sqrt(Hz) is achieved in RX and 110 dB peak DR is obtained in TX.

Flexible Light-to-Frequency Conversion Circuits Built with Si-Based Frequency-to-Digital Converters via Complementary Photosensitive Ring Oscillators with p-Type SWNT and n-Type a-IGZO Thin Film Transistors

In this study, as system-level photodetectors, light-to-frequency conversion circuits (LFCs) are realized by i) photosensitive ring oscillators (ROs) composed of amorphous indium-gallium-zinc-oxide/single-walled carbon nanotube (a-IGZO/SWNT) thin film transistors (TFTs) and ii) phase-locked-loop Si circuits built with frequency-to-digital converters (PFDC). The 3-stage ROs and logic gates based on a-IGZO/SWNT TFTs successfully demonstrate its performance on flexible substrates. Herein, along with the advantage of scalability, a-IGZO films are used as photosensitive n-type TFTs and SWNTs are employed as photo-insensitive p-type TFTs for better photosensitivity in circuit level. Through the controlling a post-annealing condition of a-IGZO film, responsivities and detectivities of a-IGZO TFTs are obtained as 36 AW^-1 and 0.3 × 10¹² Jones for red, 93 AW^-1 and 3.1 × 10¹² Jones for green, and 194 AW^-1 and 11.7 × 10¹² Jones for blue. Furthermore, as an advanced demonstration for practical application of LFCs, a unique circuit (i.e., PFDC) is designed to analyze the generated oscillation frequency (f_osc ) from the LFC device and convert it to a digital code. As a result, the designed PFDC can exactly count the generated f_osc from the flexible a-IGZO/SWNT ROs under light illumination with an outstanding sensitivity and assign input frequencies to respective digital code.