Coded Spectral Doppler Imaging: From Simulation to Real-Time Processing

Sensitivity Enhancement Using Chirp Transmission for an Ultrasound Arthroscopic Probe

Meniscal tear in the knee joint is a highly common injury that can require an ablation. However, the success rate of meniscectomy is highly impacted by difficulties in estimating the thin vascularization of the meniscus, which determines the healing capacities of the patient. Indeed, vascularization is estimated using arthroscopic cameras that lack of high sensitivity to blood flow. Here, we propose an ultrasound method for estimating the density of vascularization in the meniscus during surgery. This approach uses an arthroscopic probe driven by ultrafast sequences. To enhance the sensitivity of the method, we propose to use a chirp-coded excitation combined with a mismatched compression filter robust to the attenuation. This chirp approach was compared to a standard ultrafast emission and a Hadamard-coded emission using a flow phantom. The mismatched filter was also compared to a matched filter. Results show that, for a velocity of a few millimeters per second, the mismatched filter gives a 4.4-10.4-dB increase of the signal-to-noise ratio (SNR) compared to the Hadamard emission and a 3.1-6.6-dB increase compared to the matched filter. Such increases are obtained for a loss of axial resolution of 13% when comparing the point spread functions (PSFs) of the mismatched and matched filters. Hence, the mismatched filter allows increasing significantly the probe capacity to detect slow flows at the cost of a small loss in axial resolution. This preliminary study is the first step toward an ultrasensitive ultrasound arthroscopic probe able to assist the surgeon during meniscectomy.

Real-Time 3-D Spectral Doppler Analysis With a Sparse Spiral Array

2-D sparse arrays may push the development of low-cost 3-D systems, not needing to control thousands of elements by expensive application-specific integrated circuits (ASICs). However, there is still some concern about their suitability in applications, such as Doppler investigation, which inherently involve poor signal-to-noise ratios (SNRs). In this article, a novel real-time 3-D pulsed-wave (PW) Doppler system, based on a 256-element 2-D spiral array, is presented. Coded transmission (TX) and matched filtering were implemented to improve the system SNR. Standard sonograms as well as multigate spectral Doppler (MSD) profiles, along lines that can be arbitrarily located in different planes, are presented. The performance of the system was assessed quantitatively on experimental data obtained from a straight tube flow phantom. An SNR increase of 11.4 dB was measured by transmitting linear chirps instead of standard sinusoidal bursts. For a qualitative assessment of the system performance in more realistic conditions, an anthropomorphic phantom of the carotid arteries was used. Finally, real-time B-mode and MSD images were obtained from healthy volunteers.

Spectral Doppler Measurements With 2-D Sparse Arrays

The 2-D sparse arrays, in which a few hundreds of elements are distributed on the probe surface according to an optimization procedure, represent an alternative to full 2-D arrays, including thousands of elements usually organized in a grid. Sparse arrays have already been used in B-mode imaging tests, but their application to Doppler investigations has not been reported yet. Since the sparsity of the elements influences the acoustic field, a corresponding influence on the mean frequency (Fm), bandwidth (BW), and signal-to-noise ratio (SNR) of the Doppler spectra is expected. This article aims to assess, by simulations and experiments, to what extent the use of a sparse rather than a full gridded 2-D array has an impact on spectral Doppler measurements. Parabolic flows were investigated by a 3 MHz, 1024-element gridded array and by a sparse array; the latter was obtained by properly selecting a subgroup of 256 elements from the full array. Simulations show that the mean Doppler frequency does not change between the sparse and the full array while there are significant differences on the BW (average reduction of 17.2% for the sparse array, due to different apertures of the two probes) and on the signal power (Ps) (22 dB, due to the different number of active elements). These results are confirmed by flow phantom experiments, which also highlight that the most critical difference between sparse and full gridded array in Doppler measurements is in terms of SNR (-16.8 dB).

Ultrasound Open Platforms for Next-Generation Imaging Technique Development

Open platform (OP) ultrasound systems are aimed primarily at the research community. They have been at the forefront of the development of synthetic aperture, plane wave, shear wave elastography, and vector flow imaging. Such platforms are driven by a need for broad flexibility of parameters that are normally preset or fixed within clinical scanners. OP ultrasound scanners are defined to have three key features including customization of the transmit waveform, access to the prebeamformed receive data, and the ability to implement real-time imaging. In this paper, a formative discussion is given on the development of OPs from both the research community and the commercial sector. Both software- and hardware-based architectures are considered, and their specifications are compared in terms of resources and programmability. Software-based platforms capable of real-time beamforming generally make use of scalable graphics processing unit architectures, whereas a common feature of hardware-based platforms is the use of field-programmable gate array and digital signal processor devices to provide additional on-board processing capacity. OPs with extended number of channels (>256) are also discussed in relation to their role in supporting 3-D imaging technique development. With the increasing maturity of OP ultrasound scanners, the pace of advancement in ultrasound imaging algorithms is poised to be accelerated.

FoCUS: Fourier-Based Coded Ultrasound

Modern imaging systems typically use single-carrier short pulses for transducer excitation. Coded signals together with pulse compression are successfully used in radar and communication to increase the amount of transmitted energy. Previous research verified significant improvement in signal-to-noise ratio (SNR) and imaging depth for ultrasound imaging with coded signals. Since pulse compression needs to be applied at each transducer element, the implementation of coded excitation (CE) in array imaging is computationally complex. Applying pulse compression on the beamformer output reduces the computational load but degrades both the axial and lateral point spread function, compromising image quality. In this paper, we present an approach for efficient implementation of pulse compression by integrating it into frequency domain beamforming. This method leads to significant reduction in the amount of computations without affecting axial resolution. The lateral resolution is dictated by the factor of savings in computational load. We verify the performance of our method on a Verasonics imaging system and compare the resulting images to time-domain processing. The computational savings are evaluated for a minimal sampling rate of four times the central frequency. We show that from 4- to 33-fold reduction is achieved as a function of the resulting lateral resolution, with no degradation of axial resolution. For an imaging system operating at a higher sampling rate, e.g., 10 times the central frequency, the savings can be as high as 77-fold. The efficient implementation makes CE a feasible approach in array imaging with the potential to enhance SNR as well as improve imaging depth and frame rate.

A New Dynamic Complex Baseband Pulse Compression Method for Chirp-Coded Excitation in Medical Ultrasound Imaging

Chirp-coded excitation can increase the signal-to-noise ratio (SNR) without degrading the axial resolution. Effective pulse compression (PC) is important to maintain the axial resolution and can be achieved with radio frequency (RF) and complex baseband (CBB) data (i.e., and , respectively). can further reduce the computational complexity compared to ; however, suffers from a degraded SNR due to tissue attenuation. In this paper, we propose a new dynamic CBB PC method ( that can improve the SNR while compensating for tissue attenuation. The compression filter coefficients in the method are generated by dynamically changing the demodulation frequencies along with the depth. For PC, the obtained coefficients are independently applied to the in-phase and quadrature components of the CBB data. To evaluate the performance of the proposed method, simulation, phantom, and in vivo studies were conducted, and all three studies showed improved SNR, i.e., maximally 3.87, 7.41, and 5.75 dB, respectively. In addition, the measured peak range sidelobe level of the proposed method yielded lower values than the and , and it also derived a suitable target location, i.e., a <0.07-mm target location error, while maintaining the axial resolution. In an in vivo abdominal experiment, the method depicted brighter and clearer features in the hyperechoic region because highly correlated signals were produced by compensating for tissue attenuation. These results demonstrated that the proposed method can improve the SNR of chirp-coded excitation while preserving the axial resolution and the target location and reducing the computational complexity.