Performance Evaluation of CMUT-Based Ultrasonic Transformers for Galvanic Isolation

Gas discrimination by simultaneous sound velocity and attenuation measurements using uncoated capacitive micromachined ultrasonic transducers

Chemically functionalized or coated sensors are by far the most employed solution in gas sensing. However, their poor long term stability represents a concern in applications dealing with hazardous gases. Uncoated sensors are durable but their selectivity is poor or non-existent. In this study, multi-parametric discrimination is used as an alternative to selectivity for uncoated capacitive micromachined ultrasonic transducers (CMUTs). This paper shows how measuring simultaneously the attenuation coefficient and the time of flight under different nitrogen mixtures allows to identify hydrogen, carbon dioxide and methane from each other and determine their concentration along with identification of temperature and humidity drifts. Theoretical comparison and specific signal processing to deal with the issue of multiple reflections are also presented. Some potential applications are monitoring of refueling stations, vehicles and nuclear waste storage facilities.

Broad bandwidth air-coupled micromachined ultrasonic transducers for gas sensing

The present work aims to develop ultra-wide bandwidth air-coupled capacitive micromachined ultrasonic transducers (CMUTs) for binary gas mixture analysis. The detection principle is based on time-of-flight (ToF) measurements, in order to monitor gas ultrasound velocity variations. To perform such measurements, CMUTs were especially designed to work out of resonance mode, like a microphone. The chosen membrane size is 32 × 32 µm² and gap height is 250 nm. The resonance frequency and collapse voltage were found at 8 MHz and 58 V respectively. As mentioned, the CMUTs were exploited in quasi-static operating mode, in a very low frequency band, from 1 MHz to 1.5 MHz frequencies. The transducer impulse response was characterised, and a -6 dB relative fractional frequency bandwidth (FBW) higher than 100% was measured, enabling to use CMUT for the targeted application. Additionally, a measuring cell has been designed to hold the fabricated CMUT emitter and receiver prototypes facing each other. The volume inside the cell was kept lower than 3 mL and the surface of emitter/receiver was 1.6 × 8 mm². To validate the general principle of the proposed technique, two binary gas mixtures of CO₂/N₂ and H₂/N₂, with varying concentrations, have been tested. The results are very promising with a measured limit of detection (LOD) of 0.3% for CO₂ in N₂ and 0.15% for H₂ in N₂.

Closed-Form Expressions on CMUTs With Layered Anisotropic Microplates Under Residual Stress and Pressure

Capacitive micromachined ultrasonic transducers (CMUTs) are promising in the emerging fields of personalized ultrasonic diagnostics, therapy, and noninvasive 3-D biometric. However, previous theories describing their mechanical behavior rarely consider multilayer and anisotropic material properties, resulting in limited application and significant analysis errors. This article proposes closed-form expressions for the static deflection, collapse voltage, and resonant frequency of circular-microplate-based CMUTs, which consider both the aforementioned properties as well as the effects of residual stress and hydrostatic pressure. These expressions are established by combining the classical laminated thin plate (CLTP) theory, Galerkin method, a partial expansion approach for electrostatic force, and an energy equivalent method. A parametric study based on finite-element method simulations shows that considering the material anisotropy can significantly improve analysis accuracy (~25 times higher than the theories neglecting the material anisotropy). These expressions maintain accuracy across almost the whole working voltage range (up to 96% of collapse voltages) and a wide dimension range (diameter-to-thickness ratios of 20-80 with gap-to-thickness ratios of ≤2). Furthermore, their utility in practical applications is well verified using numerical results based on more realistic boundary conditions and experimental results of CMUT chips. Finally, we demonstrate that the high accuracy of these expressions at thickness-comparable deflection results from the extended applicable deflection range of the CLTP theory when it is used for electrostatically actuated microplates.

Evaluation of capacitive micromachined ultrasonic transducers for passive monitoring of microbubble-assisted ultrasound therapies

Passive cavitation detection can be performed to monitor microbubble activity during brain therapy. Microbubbles under ultrasound exposure generate a response characterized by multiple nonlinear emissions. Here, the wide bandwidth of capacitive micromachined ultrasonic transducers (CMUTs) was exploited to monitor the microbubble signature through a rat skull and a macaque skull. The intrinsic nonlinearity of the CMUTs was characterized in receive mode. Indeed, undesirable nonlinear components generated by the CMUTs must be minimized as they can mask the microbubble harmonic response. The microbubble signature at harmonic and ultra-harmonic components (0.5-6 MHz) was successfully extracted through a rat skull using moderate bias voltage.